Intel GA-945P-DS3/S3 user manual English

Page 63

8 Channel Audio Setup

STEP 1 :

After installation of the audio driver, you should find an Audio Manager icon in your system tray (you can also find the icon in Control Panel). Double- click the icon to open the Audio Control Panel.

STEP 2:

In the Audio Control Panel, click the Audio I/O tab. In the upper left list, click 8CH Speaker.

STEP 3:

After plugging in 8-channel speakers to the rear speaker jacks, a small window will pop up and ask you what type of equipment is connected. Choose a device depending on the type of speaker connected (8-channel audio consists of Front Speaker Out (Line Out), Rear Speaker Out, Cen- ter/Subwoofer Speaker Out, and Side Speaker Out) then click OK. The 8-channel audio setup is completed.

English

- 63 -

Appendix

Image 63

Contents GA-945P-DS3/S3 Motherboard Product Manual Classification CopyrightTable of Contents Install Drivers Item Checklist GA-945P-DS3/GA-945P-S3 Motherboard Layout Block Diagram Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantyCPU Feature SummaryMbit flash ROM Installation of the CPU Installation of the CPU and CPU CoolerInstallation of the CPU Cooler Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector Nbfan Chip Fan Power Connector 5 Cpufan / Sysfan / Pwrfan Cooler Fan Power ConnectorIDE1 IDE Connector FDD Floppy ConnectorPwrled SATAII0/1/2/3 Sata 3Gb/s ConnectorFpanel Front Panel Jumper Faudio Front Audio Connector Spdifio S/PDIF In/Out Connector Cdin CD in ConnectorCI Chassis Intrusion, Case Open USB1 / FUSB2 Front USB ConnectorClrcmos Clear Cmos English Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example GA-945P-DS3 Bios Ver. F2c „ PnP/PCI Configurations „ Standard Cmos Features„ Advanced Bios Features „ Power Management SetupIDE Channel 2, 3 Master/Slave Standard Cmos FeaturesTime IDE Channel 0 Master/SlaveMemory Floppy 3 Mode Support for Japan AreaDrive a Halt onPassword Check Advanced Bios FeaturesHard Disk Boot Priority First / Second / Third Boot DeviceNo-Execute Memory ProtectNote HDD S.M.A.R.T. CapabilityCPU Hyper-Threading Note Limit Cpuid Max. to 3NoteSmart LAN Integrated PeripheralsUSB Mouse Support Smart LAN LAN Cable Diagnostic FunctionUSB 2.0 Controller USB Keyboard SupportOnboard Parallel Port OnBoard LAN Boot ROMParallel Port Mode Onboard Serial PortECP Mode Use DMA Power Management SetupAC Back Function Power On By MousePower On By Keyboard KB Power on PasswordPCI1 IRQ Assignment PnP/PCI ConfigurationsPC Health Status CPU Smart FAN Control CPU Smart FAN ModeA.2 MB Intelligent TweakerM.I.TCPU Clock Ratio Note Robust Graphics BoosterPCI Express Frequency Mhz FSB1333 Core CPUCPU Host Clock Control CPU Host Frequency MhzLoad Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupInstall Chipset Drivers Install DriversDriver CD Information Software ApplicationsContact Us Hardware InformationEnglish Unique Software Utilities EasyTune 5 IntroductionUser Interface Overview System requirements Xpress Recovery2 IntroductionHow to use the Xpress Recovery2 Boot from CD/DVD F9 Xpress Recovery2Main Screen of Xpress Recovery2 PrecautionsLimitations Before Use Flash Bios Method IntroductionUpdating the Bios Method 1 Q-FlashTMCopy Bios completed Pass Please press any key to continue Methods and steps Method 2 @BIOSTM UtilityEnglish 4 2- / 4- / 6- / 8- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English English Sound Effect Configuration Troubleshooting English English English English Taiwan Headquarters Contact UsGigabyte Global Service System