Intel GA-8I915PL-G user manual Password Check, CPU Hyper-Threading, Limit Cpuid Max. to

Page 35

Password Check

Setup

The system will boot but will not access to Setup page if the correct

 

password is not entered at the prompt. (Default value)

System

The system will not boot and will not access to Setup page if the correct

 

password is not entered at the prompt.

If you want to cancel the setting of password, please just press ENTER to make [SETUP] empty.

CPU Hyper-Threading

Enabled

Enables CPU Hyper Threading Feature. Please note that this feature is only working

 

for operating system with multi processors mode supported. (Default value)

Disabled

Disables CPU Hyper Threading.

Limit CPUID Max. to 3

Enabled

Limit CPUID Maximum value to 3 when use older OS like NT4.

Disabled

Disables CPUID Limit for windows XP. (Default value)

No-Execute Memory Protect(Note)

Enabled

Enables No-Execute Memory Protect function.

Disabled

Disables No-Execute Memory Protect function. (Default value)

CPU Enhanced Halt (C1E) (Note)

Enabled

Enables CPU Enhanced Halt (C1E) function.

Disabled

Disables CPU Enhanced Halt (C1E) function. (Default value)

CPU Thermal Monitor 2 (TM2) (Note)

Enabled

Enable CPU Thermal Monitor 2 (TM2) function.

Disabled

Disable CPU Thermal Monitor 2 (TM2) function. (Default value)

English

(Note) This item will show up when you install a processor which supports this function.

- 35 -

BIOS Setup

Image 35
Contents GA-8I915PL-G Motherboard Product Manual Classification CopyrightTable of Contents Install Drivers GA-8I915PL-G GA-8I915PL-G Motherboard LayoutBios Page Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantyCPU Feature SummaryUse of licensed Award Bios Installation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of Memory Dual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector FDD Floppy Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATA0/SATA1/SATA2/SATA3 Serial ATA Connector IDE1 IDE ConnectorFpanel Front Panel Jumper Pwrled Faudio Front Audio ConnectorSpdifio Spdif In/Out Cdin CD14 IR USB1 / FUSB2 Front USB ConnectorClrcmos Clear Cmos CI Chassis Intrusion, Case OpenBATBattery English Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. D2 Standard Cmos Features Drive a / Drive B IDE Channel 0 Master, SlaveIDE Channel 2/3 Master, Slave Base Memory Floppy 3 Mode Support for Japan AreaHalt on MemoryFirst / Second / Third Boot Device Advanced Bios FeaturesHard Disk Boot Priority No-Execute Memory ProtectNote Password CheckCPU Hyper-Threading Limit Cpuid Max. toSata Port 1/3 Set to Integrated PeripheralsSata Port 0/2 Set to USB Keyboard Support Onboard LAN Boot ROMUSB Controller USB 2.0 ControllerECP Mode Use DMA Uart Mode SelectUR2 Duplex Mode Parallel Port ModePower On By Mouse Power Management SetupResume by Alarm AC Back Function Power On By KeyboardKB Power on Password PCI 1 IRQ Assignment PnP/PCI ConfigurationsPC Health Status CPU Clock Ratio CPU Smart FAN ModeMB Intelligent TweakerM.I.T CPU Smart FAN ControlCPU Host Frequency Mhz Robust Graphics BoosterA.2 CPU Host Clock ControlFSB OverVoltage Control Memory Frequency MhzDimm OverVoltage Control PCI-E OverVoltage ControlLoad Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupInstall Chipset Drivers Install DriversDriver CD Information Software ApplicationsContact Us Hardware InformationEnglish Unique Software Utilities User Interface Overview EasyTune 5 IntroductionHow to use the Xpress Recovery Xpress Recovery IntroductionWhat is Xpress Recovery ? F9 For Xpress Recovery Exit and Restart Remove Backup Image  Remove backup image. Are you sure? Y/NBefore You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Task menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to 4 to flash the backup BIOS, too Part Two FlashTMutility bar Exploring the Q-FlashTMutility screenCongratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM UtilityEnglish 4 2- / 4- / 6- / 8- ChannelAudio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English Step Jack-Sensing and UAJ Introduction English Troubleshooting English English English English English Taiwan Headquarters Contact UsChina Shanghai