Intel 430TX user manual Cd-Rom

Page 46

A6>

Do not install the driver on a system equipped with these CD-

 

ROM drives. There are no plans to support these drives with

 

the PIIX Bus Master river.

Q7>

The driver does not support the following fixed disk drives:

 

Conner CFA850A

 

Maxtor 71626A

 

Maxtor 71260AT

A7>

Do not install the driver on a system equipped with these fixed

disk drives. There are no plans to support these drives with the PIIX Bus aster driver.

Q8>

Windows 95 fails to report the actual size of the drive.

 

-OR-

 

Data loss or system hang has occurred after installing the

 

PIIX Bus Master driver.

A8>

If your disk drive is > 528MB, you should check and compare

 

the capacity of the drive before and after installing PIIX Bus

 

Master IDE driver.

 

If the system fails to operate reliably, de-install the driver.

It is recommended to de-install the system in Safe mode: Press the "F8" function key when you see "Starting Windows 95"; Select "Safe mode"; and de-install the Intel driver after the

system has re-booted.

Q9>

How can I play MS-DOS based CD-ROM games?

-OR-

 

I could not access my CD-ROM drive in MS-DOS real mode.

A9>

Your CD-ROM drive is not available in MS-DOS mode because

 

CD-ROM

real-mode driver is not loaded.

There is a

 

conflict between Intel PIIX Bus Master IDE driver and a DOS

 

real-mode ATAPI CD-ROM device driver.

 

 

This conflict occurs when both the real-mode driver and the

 

PIIX Bus

Master IDE driver attempt to access the resources of

the PIIX controller.

46

Image 46
Contents USER’S Manual Update Inforamtion Content Chapter Eide Hardware Installation for TX2 Preface Simple features Page Chapter Map of ATX586 Mother Board AMD MMXNON-ACTIVE JP8/91-2 Short CPUJP15 2MB Flash Bios only Short 256K PB SramInstall System Dram Memory Install IDE, Enhanced I/O and Front Panel Connectors GND PIN-3 Irtx PIN-4 VCC COM2 IRQ DRQ GameCOM1 COM3CN1 COM1 CN2 JP8JP9 CN3Page Chapter Bios Features Setup Chipset Features Setup PNP/PCI Configuration Post Read Cmos data into Bios stack area If Eisa NVM checksum is good, execute Eisa initialization Write all Cmos values currently in the Bios stack area back If there is any changes in the hardware configuration Quick Installation Guide Page Introduction Contents of this DocumentSystem Requirements SETUP.INS Contents of the Distribution PackageSETUP.EXE BMIDE95.EXESETUP.LIB SETUP.DLLInstalling the Software Verifying Installation of the Driver Page DE-INSTALLING the Software SB, ABPage Troubleshooting Common ProblemsPage Release Notes \WINDOWS\SYSTEM\IOSUBSYS8A. IDE Devices Supported by the Driver 8B. Applications Supported by the Driver 8C. Large IDE Fixed Disk Drive 528MB Support by the Driver CDU55E NEC* CDR261 8D. RELEASE-SPECIFIC Troubleshooting InformationNEC* CDR251 CDU76E NEC* CDR271NEC* CDR273 NEC* CDR272IDE One or more of the IDE/ATAPI drives on the system fail to CD-ROM DOS=HIGH,UMB 8E. Revision History InformationVersion 2.64 Release Version 3.00 ReleaseCFS425A CFS850A 8F. Release Testing InformationCFA540A IBMNEC CRD-S54P CDU55E CDU76E CDU77E CDU311-GI Teac CD44E CD56EPage From the Bios of new main board to old main board Hardware Installation For TX2 SHORT, 2-4 Open Map of TX2 Mother Board JP8 4-5 Short for CyrixShort for 5v Flash Bios normal. Default Open Normal Power mode. Default Total Install IDE, Enhanced I/O and Front Panel Connectors USB+, PIN-4 GND JP3 LPT3 3BC-3BFJP1 JP4Pin Definition for Cable Connection

430TX specifications

The Intel 430TX chipset, introduced in the mid-1990s, was a significant advancement in computer technology, primarily designed to support Intel's Pentium processors. This chipset catered to the growing demand for improved multimedia performance, better system stability, and expanded features to accommodate developing applications.

One of the main features of the Intel 430TX was its support for Dual Independent Bus architecture. This allowed for simultaneous data transfers between the CPU and the memory, significantly improving system performance. The chipset supported up to 512 MB of EDO (Extended Data Out) RAM and featured a memory bus that could handle speeds of up to 66 MHz, making it suitable for a variety of applications ranging from home computing to business use.

Another significant characteristic of the 430TX was its integration of a PCI (Peripheral Component Interconnect) bus, which allowed for higher bandwidth compared to the older ISA (Industry Standard Architecture) connections. The chipset provided up to five PCI slots, facilitating the addition of modern peripherals like graphics cards, sound cards, and network interfaces without compromising system performance. This flexibility was vital as multimedia applications became increasingly common during that era.

The Intel 430TX also incorporated support for the newer ATA/33 standard for hard drives, allowing for faster data transfer rates compared to previous standards. This enhancement contributed to improved overall system responsiveness. Moreover, the chipset partially supported USB (Universal Serial Bus) devices, paving the way for the increasingly popular external peripherals that were emerging at the time.

In terms of power management, the 430TX featured advanced management capabilities, allowing the system to achieve better energy efficiency through features such as ACPI (Advanced Configuration and Power Interface) support. This was particularly important as users began to prioritize environmental concerns alongside performance.

Overall, the Intel 430TX chipset represented a balance of performance, compatibility, and innovative feature integration. Its legacy is evident in the foundational technologies it helped propel, influencing the design and features of future chipsets. Today, revisiting the Intel 430TX illustrates the rapid technological evolution that has occurred since its introduction, underscoring its importance in the development of modern computer systems. The 430TX was pivotal in bridging the gap between early PC architectures and the advanced systems we utilize today.