Intel 2804040 user manual Block Diagram, Intel Pentium 4 with 775 pin Plga processor, Intel 945G

Page 11

2804040 User’s Manual

Introduction

1.4 <Block Diagram>

Intel Pentium 4 with 775 pin PLGA processor

Intel GMA950 Graphics

PCI-Express x16

8GB/s

6.4GB/s

Intel 945G

GMCH

2x 240-pin DDR2 400/533/667MHz up to 2GB

SMBus 2.0

4 x USB2.0 ports

IDE

2GB/s		DMI

300MB/s

ICH7R

4 x Serial ATA II ports

ALC 880 AC97 7.1CH Codec

2 x Serial ports

1 x Floppy port

8-bit GPIO

4 x Marvell E8053

Gigabit LAN

Mini-PCI slot

2 X IEEE1394

PCI bus

BIOS

Block Diagram

11

Image 11

Contents

2804040 User’s Manual DisclaimerTrademark Cable Kit Other AccessoriesPacking List HardwareIntroduction Hardware SetupIndex User’s ManualInd exUser’s Manual Ind ex System ConfigurationBios Setup Appendix a I/O Port Pin Assignment Appendix D Programming GPIOs………………………………………………59This Page is Left for Blank Product Overview IntroductionVGA Display Interface Product SpecificationMulti-I/O Port Expansive Interface Power and EnvironmentEthernet Interface Audio InterfaceComponent Placement Component PlacementIntel 945G Block DiagramBlock Diagram Intel Pentium 4 with 775 pin Plga processorMechanial Drawing Mechanical DrawingConnector Location Connector LocationUser’s Manual Hardware Setup Jumper Reference Cmos Operating/Clear SettingJumper Reference Jumper FunctionConnector Function Connector ReferenceInternal Connectors External ConnectorsCPU Installation CPU and Memory SetupCPU installation Memory Installation Memory installationMode Cmos SetupCmos Setup Jumper Jrtc Type Onboard 3-pin jumperEnhanced IDE Interface Enhanced IDE interfaceSerial ATA Installation Serial ATA installationFloppy Installation Floppy InstallationLAN Installation LAN installationAudio Installation Audio InstallationPin Description User’s Manual Introduction Connector CnaudioConnector Cdin Connector SpdifDisplay Installation Display InstallationInterface IEEE1394 USB2.0 IEEE1394 and USB InstallationIEEE1394 and USB Installation VCC Power and Fan Installation Power and Fan InstallationPIN assignment Gpio Interface Gpio interfaceSerial Port Serial PortPin Number Pin Assignment Switch and Indicator Switch and IndicatorExpansion Interface Expansion InterfaceUser’s Manual This Page is Left for Blank Parallel ATA Serial ATA System ConfigurationSata configuration Sata Mode On-Chip Serial ATA mode RAID 10 RAID 0+1 Sata RAID ConfigurationSata RAID Configuration RAID 5 striping with parityUser’s Manual System Configuration Select Actions to Create RAID Volume Repeat the to create second volume as RAID Level Audio Configuration Video Memory Setup Total Memory Frame Graphic Buffer Size User’s Manual Fixed + Dvmt Memory SizeSystem On-Chip Fixed Display Properties Setting Display Properties SettingDevices PEG Force PCI-Express interface settingPCI-Express Interface setting Bios SetupUser’s Manual Bios Setup This Page is Left for Blank Serial ATA Port Connector SATA1/2/3/4Appendix a I/O Port Pin Assignment IDE PortUser’s Manual P o r t Pin Assignment Floppy PortIrDA Port Pin VGA PortLAN Port Pin Description TRD0+ TRD0- TRD1+User’s ManualI/O P o r t Pin Assignment Ieee 1394 PortSMBus User’s Manual System Resources Appedix B System ResourcesB1.I/O Port Address Map User’s Manual P o r t Pin Assignment B2.Memory Address Map B3.System IRQ & DMA Resources Flash Method Appedix C Flash BiosBios Auto Flash Tool Programming GPIO’s Appendix D Programming GPIO’sUser’s Manual Con tact Information Contact Information