Intel Celeron M Half Size CPU Card With VGA/LAN Video OFF Option, Video OFF Method, Modem USE IRQ

Page 63

Chapter 4 Award BIOS Setup

VIDEO OFF OPTION:

When enabled, this feature allows the VGA adapter to operate in a power saving mode.

Always On	Monitor will remain on during power saving modes.
Suspend --> Off	Monitor blanked when the systems enters the Suspend
	mode.
Susp,Stby --> Off	Monitor blanked when the system enters either Suspend or
	Standby modes.
All Modes --> Off	Monitor blanked when the system enters any power saving
	mode.

VIDEO OFF METHOD:

This determines the manner in which the monitor is blanked.

V/H SYNC+Blank	This selection will cause the system to turn off the vertical
	and horizontal synchronization ports and write blanks to the
	video buffer.

Blank Screen	This option only writes blanks to the video buffer.
DPMS	Select this option if your monitor supports the Display
	Power Management Signalling (DPMS) standard of the
	Video Electronics Standards to select video power
	management values.

MODEM USE IRQ:

This item enable you to name the interrupt request (IRQ) line assigned to the modem (if any) on your system. Activity of the selected IRQ always awakens the system.

SUSPEND MODE:

When enabled and after the set time of system inactivity, all devices except the CPU will be shut off.

SOFT-OFF BY PWR-BTTN:

Pressing the power button for more than 4 seconds forces the system to enter the Soft-Off state when the system has “hung”. The choices are Delay 4 Sec and Instant-Off.

WAKE-UP BY PCI CARD:

An input signal from PME on the PCI card awakens the system from a soft off state.

Page: 4-18

PCI-471LF USER′S MANUAL

Image 63

Contents USER’S Manual PCI-471LF Celeron M FCC Notice Table of Contents Software Utilities Appendix a Expansion BUS Introduction About this Manual Hardware ConfigurationCPU System SpecificationDisplay Safety Precautions Hardware Jumper & Connector Quick Reference Table Component Locations PCI-471LF Connector, Jumper and Component locationsJumpers and Caps HOW to SET the JumpersJumper Settings Jumper DiagramsRS-232 RS-422 RS-485 COM Port ConnectorCOM1 RI & Voltage Selection COM2 RI & Voltage Selection RS232/422/485 COM2 Selection Jumper Settings Function Pin closed IllustrationsKeyboard or PS/2 Mouse Connector Keyboard or PS/2 Mouse SelectionKeyboard PS/2 Mouse Jpaenl 9,11 Reset Connector External Keyboard ConnectorReset Connector Hard Disk Drive LED ConnectorJpanel 10,12 ATX Power Button ATX Power ButtonExternal Speaker Connector Power LED ConnectorKeylock Connector Irda ConnectorCPU FAN Connector Clear Cmos Data Selection System FAN ConnectorVGA Connector PIN Assignment Hard Disk Drive ConnectorFloppy Disk Drive Connector Printer Connector LAN Connector Universal Serial BUS ConnectorVSB Connector ATX Power ConnectorPCI Slot 3.3V Voltage Selection Inverter ConnectorManufacturing Default is set as open RESET/NMI/CLEAR Watchdog Selection32. AT/ATX Power Selection CNT3 Lvds ConnectorLvds Panel Voltage Selection Software Utilities Introduction VGA Driver UtilityFilename Purpose Assume that CD ROM drive is D To update VGA Bios for LCD Flat Panel Display Flash Bios UpdateInstallation of VGA Driver System Bios UpdatePage3-4 Introduction LAN Driver UtilityInstallation of Utility for Windows 98SE/ME/2000/XP Intel Chipset Software Installation UtilityInstallation of Utility for Windows 98SE/ 2000/XP USB2.0 Software Installation UtilityConfiguration Sequence Watchdog Timer ConfigurationPage3-9 Award Bios Setup Introduction Setup program initial screen Entering SetupCmos Setup screen Standard Cmos FeaturesIDE Primary Master / Slave IDE Secondary Master / Slave Base Memory Drive a and Drive BVideo Halt onAward Hard Disk Type Table Hard Disk AttributesCPU L1 & L2 Cache Advanced Bios FeaturesBios Features Setup Screen Quick Power on SELF-TESTTypematic Rate Setting FIRST/SECOND/ Boot DeviceBoot UP Floppy Seek Boot UP Numlock StatusAdvanced Chipset Features Chipset Features Setup ScreenOS Select for Dram 64MB Delayed Transaction Dram Data Integrity ModeSystem Bios Cacheable Video Bios CacheableIntegrated Peripherals Integrated Peripherals Setup ScreenPrimary Master/Slave Udma Secondary Master/Slave Udma VIA Onchip IDE DeviceOnChip Primary PCI IDE Primary Master/Slave PIO Secondary Master/Slave PIOOnboard Device Super IO Device Onboard Parallel Port Parallel Port ModeEPP Mode Select ECP Mode Use DMAAcpi Suspend Type Power Management SetupPower Management Setup Screen Power ManagementModem USE IRQ Suspend ModeVideo OFF Option Video OFF MethodPM Events Resume by AlarmPNP/PCI Configuration PNP/PCI Configuration Setup ScreenReset Configuration Data Resource Controlled by IRQ ResourcesIRQ-n Assigned to Current System FAN Speed Current Warning TemperatureCurrent CPU Temperature PC Health StatusAuto Detect PCI CLK Frequency Control Setup ScreenFrequency Control VcoreLoad Optimized Defaults Load FAIL-SAFE DefaultsPassword Setting To SET a PasswordTo Disable the Password Save & Exit Setup Exit Without Saving Expansion BUS PCI BUS PIN Assignment Epci Connector PIN Assignment Compact Flash Card Connector PIN AssignmentTechnical Summary Block Diagram IRQ Assignment Interrupt MAPCode Assignment RTC & Cmos RAM MAPTimer & DMA Channels MAP Timer Channel Map AssignmentDMA Channel Map Assignment Memory MAP Memory MapMap