Lenovo RD120 manual German Ordinance for Work gloss statement, Electronic emission notices

Page 110

unsorted municipal waste, but use the collection framework available to customers for the return, recycling, and treatment of batteries and accumulators. Customer participation is important to minimize any potential effects of batteries and accumulators on the environment and human health due to the potential presence of hazardous substances. For proper collection and treatment, go to http://www.lenovo.com/lenovo/environment.

For California:

Perchlorate material - special handling may apply. See http://www.dtsc.ca.gov/ hazardouswaste/perchlorate/.

The foregoing notice is provided in accordance with California Code of Regulations Title 22, Division 4.5 Chapter 33. Best Management Practices for Perchlorate Materials. This product/part may include a lithium manganese dioxide battery which contains a perchlorate substance.

German Ordinance for Work gloss statement

The product is not suitable for use with visual display work place devices according to clause 2 of the German Ordinance for Work with Visual Display Units.

Das Produkt ist nicht für den Einsatz an Bildschirmarbeitsplätzen im Sinne § 2 der Bildschirmarbeitsverordnung geeignet.

Electronic emission notices

The following section includes statements related to electronic emissions.

Federal Communications Commission (FCC) statement

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. Lenovo is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Industry Canada Class A emission compliance statement

This Class A digital apparatus complies with Canadian ICES-003.

96ThinkServer RD120 Types 6444, 6445, 6446, and 6447: User Guide

Image 110
Contents User Guide Page User Guide Page Contents Configuring the server Safety Page To Connect To Disconnect Page Safety Statement Safety Page ThinkServer RD120 server Related documentation Features and specifications What your server offers Baseboard management controllerLarge data-storage and hot-swap capability EasyManage softwareIntegrated network support Memory mirroring Easy LED DiagnosticsRedundant cooling and power capabilities Online-spare memoryTCP/IP offload engine TOE support Reliability, availability, and serviceability featuresSystems-management capabilities Front view Server controls, LEDs, and powerThinkServer EasyStartup Tape drive bay Rear view 10 USB 3 connector 20 Power supply Server power features Turning on the serverThinkServer RD120 server Page Installing optional devices Server componentsCover VRM System-board optional-device connectors PCI riser-card adapter connectors Power-backplane-board connectorsSystem-board internal cable connectors System-board external connectors System-board switches and jumpers Switch Number Default value Description System-board LEDs LEDRiser-card assembly LEDs Diagnostics panel LEDCPU RAID Installation guidelines Working inside the server with the power on System reliability guidelinesHandling static-sensitive devices Removing the coverRemoving the riser-card assembly 1 Access holes 2 Release tabs Installing the riser-card assembly Removing the microprocessor air baffleFinger holes Installing the microprocessor air baffle Removing the Dimm air baffle Installing the Dimm air baffle Installing an adapter PCI riser card 1 Access holes 2 Release tabs 1 Access holes 2 Guide 3 Release tabs 4 Guide Removing an adapter To remove an adapter, complete the following steps1 Access holes 2 Release tabs Replacing the RAID SAS controller RAID controller Installing a hard disk drive Inch drivesInch drives Removing a hard disk drive Installing an optional tape drive Installing a Sata tape drive in a 3.5-inch model serverInstalling optional devices 1 Sata tape cable connector 2 Sata tape cable Installing a Sata tape drive in a 2.5-inch model server Installing a microprocessor Installing optional devices Microprocessor-socket dust cover Installing optional devices Notches Installing optional devices Installing a memory module Pair Dimm connectorsDimm Memory mirroring Online-spare memory Configuration that you use, install the largest DIMMs first Installing a hot-swap power supply Removing a memory moduleTo install an ac power supply, complete the following steps Power cord connectors Removing a hot-swap power supply Installing a fanRemoving a fan Removing the fan-bracket assembly Fan bracket Installing the fan-bracket assembly Replacing the CD-RW/DVD drive Completing the installation Front view Installing the coverConnecting the cables Updating the server configuration Rear viewInstalling optional devices Page Using the Configuration/Setup Utility program Starting the Configuration/Setup Utility program Configuration/Setup Utility menu choicesAdvanced Setup Administrator PasswordPower-on Password Memory SettingsCPU Options RSA II SettingsStatic IP Settings PCI Bus ControlReboot System on NMI BMC Post Watchdog TimeoutBMC Serial Port Access Mode BMC Network ConfigurationRestore Settings PasswordsSave Settings Load Default SettingsAdministrator password Boot block recovery jumper J42 Using the RAID Configuration Utility program Starting the RAID Configuration Utility programViewing the configuration RAID Configuration Utility menu choicesConfiguring the controller Using the baseboard management controllerUsing the baseboard management controller utility programs Configuring the Gigabit Ethernet controllersPage Appendix. Notices Trademarks Important notes Waste electrical and electronic equipment Weee notices Recycling statements for Japan Battery return program For the European UnionFederal Communications Commission FCC statement German Ordinance for Work gloss statementElectronic emission notices Industry Canada Class a emission compliance statementTaiwanese Class a warning statement Avis de conformité à la réglementation d’Industrie CanadaEuropean Union EMC Directive conformance statement Page Index Installing VRM Index Video connector rear Voltage regulator module, installing Page Part Number 46U0861