Sanyo PLC-XTC50L owner manual Lamp Replacement, Top Control

Page 64

Maintenance and Care

Lamp Replacement

When the total lighting time of a Projection Lamp reaches the recommended total hours of use, the Lamp replacement icon appears on the screen and LAMP 1 / 2 REPLACE indicator lights yellow. Replace the lamp with a new one promptly. The timing when the LAMP 1 / 2 REPLACE indicator should light is depending on the lamp mode.

Top Control

LAMP 1/2 REPLACE indicators

Lamp replacement icon

✔Note:

•The Lamp replacement icon will not appear when the Display function is set to “Off” (p.54), or during “Freeze” (p.30).

CAUTION

Allow a projector to cool for at least 45 minutes before you open the Lamp cover. The inside of the projector can become very hot.

CAUTION

For continued safety, replace with a lamp of the same type lamp. Do not drop the lamp or touch the glass bulb! The glass can shatter and may cause injury.

CAUTION

When replacing the lamp because it has stopped illuminating, there is a possibility that the lamp maybe broken. If replacing the lamp of a projector which has been installed on the ceiling, you should always assume that the lamp is broken, and you should stand to the side of the lamp cover, not underneath it. Remove the lamp cover gently. Small pieces of glass may fall out when the lamp cover is opened. If pieces of glass get into your eyes or mouth, seek medical advice immediately.

Follow these steps to replace the lamp.

1	Check the number of lamp to be replaced on the Lamp
1	Status Display or the LAMP 1/2 REPLACE indicators
	and replace the lamp.
2	Turn off the projector and unplug the AC power cord.
	Let the projector cool for at least 45 minutes.
3	Remove the screw that secures the lamp cover with a
3	coin, and then open the lamp cover.
4	Lift the lamp out of the projector by using the handle.
5	Replace the lamp with a new one. Make sure that
5	the lamp is set properly. Put the lamp cover back and

secure it with the screw.

✔Note:

•After lamp replacement, make sure to check the Lamp mode (p.52).

Lamp cover

Screw

Lamp 1

Handle

Lamp 2

64

Image 64

Contents Model PLC-XTC50L Features and Design Table of Contents Safety Precaution To the OwnerSafety Instructions Air Circulation Top ControlInstalling the Projector in Proper Directions Positioning PrecautionsMoving the Projector Transporting the ProjectorAC Power Cord for the United Kingdom AC Power Cord for the United States and CanadaCompliance Front Part Names and FunctionsBack Side Terminal Audio 2 JackAudio 3 Jacks LMONO/R BNC Input Jacks0USB Connector Series B 1R/C JackTop Control Remote Control 4P-TIMER button 9RESET/ON/ALL-OFF switch5D..ZOOM button 6ZOOM ed buttonsRemote Control Battery Installation Wired Remote ControlRemote Control Code Installation Adjustable FeetRemoving the lens Lens InstallationAttaching the lens to the projector Connecting to a Computer Digital and Analog RGB Cables used for connection VGAConnecting for Audio Signal Monitor OUT and Audio OUT SpecificationsConnecting the AC Power Cord Projector side AC outlet sideWhat is PIN code? Basic OperationTurning On the Projector Enter a PIN codeTurning Off the Projector Remote Control How to Operate the On-Screen MenuOn-Screen Menu Menu Bar Zoom Adjustment Focus AdjustmentLens Shift Adjustment Operating with Projector ControlDirect Operation Sound AdjustmentMenu Operation Operating with Remote Control Shutter button Timer buttonKeystone button Pointer Function Laser Pointer FunctionSpotlight Wireless Mouse Operation Presentation Pointer buttonRemote Control Operation Remote Control button operationInput Selection InputInput Source Selection Input MenuRGB PC analog RGB Scart RGB PC digital Video ComponentVideo System Selection Video or S-videoComponent AV System Menu Video or S-videoComputer Adjustment Computer System SelectionSelecting Computer System Manually PC System MenuAuto PC Adjustment PC Adjust MenuTo store adjustment parameters Auto PC AdjManual PC Adjustment To clear the adjusted data To store the adjusted dataImage Level Selection Image Level SelectionImage Menu Image Adjustment Image AdjustmentImage Adjust Menu Sharpness GammaNoise reduction ProgressiveTo reset the adjusted data, select Reset and press Screen Adjustment Screen AdjustmentScreen Menu KeystoneScreen Size Adjustment Computer Signals Digital zoom + For zooming in and out the imagesDigital zoom Screen Size Adjustment Video, Component Signals Setting SettingSetting Menu Language LogoCapture Logo PIN code lockEnter a Logo PIN code Change the Logo PIN code lock settingChange the Logo PIN code Lamp control Lamp modeLamp life control Pointer Standby mode Power managementDisplay DisplayOn start Slant settingSlant Key lock Security Key lock and PIN code lock settingsKey lock Change the PIN code lock setting Change the PIN code lock settingPIN code lock Enter a PIN codeChange the PIN code Change the PIN codeTest pattern Factory default Factory defaultMaintenance and Care Filter InstructionsReplacing the Filter Cartridge Filter counter Scroll counterLamp 1/2 Replace Indicators Lamp Mode ChangeoverAuto Lamp Selection System Lamp Status DisplayLamp Replacement POA-LMP125 Service Parts No 342 Replacement Lamp Type NoModel No.. of your projector Then check the matters below Cleaning the Projection Lens Cleaning the Projector CabinetTroubleshooting ProblemNo power AppendixAuto PC adjustment function During the operation Setting does not remain afterTurning off power Power management function doesRemote Control does Wired remote control does notWireless Mouse function does Indicator blinks or lightsMenu Tree InputSystem InformationPC Adjust Screen SettingIndicators and Projector Condition Projector is operating normallyProjector is detecting abnormal condition ImmediatelyIf the Filter counter reached a time set in the timer Compatible Computer Specifications ON-SCREEN Resolution59.940 Technical Specifications Optional Parts PJ Link Notice Configurations of Terminals Terminal Analog RGB Mini D-sub 15 pin InputOutput Terminal D-sub 9 pinPIN Code Number Memo Logo PIN Code Lock NoDimensions KH7AL