Sanyo PLC-XT15 To change the code of Projector, To change the code of the Remote Control Unit

Page 37

SETTING

Power management

This function turns Projection Lamp off when this projector detects signal interruption and is not used for a certain period in order to reduce power consumption and maintain the Lamp-life. (This projector is shipped with this function ON.)

Power Management function operates to turn Projection Lamp off when the input signal is interrupted and any button is not pressed over 5 minutes. This function operates as follows;

1.When any input signal is interrupted, “No signal” and the counting down display appears (for 5 minutes).

2.After counting down for 5 minutes, Projection Lamp and READY Indicator are turned off. (Cooling Fans keep running.)

3.READY Indicator starts to flash after cooling down Projection Lamp about for 90 seconds (Power Management mode).

In this Power Management mode, Projection Lamp is automatically turned on when the input signal is connected or projector is operated with any button on Top Control or on Remote Control Unit again.

On start

When this function is “On,” projector is automatically turned on just by connecting AC Power cord to a wall outlet.

Note ; Be sure to turn projector off properly (refer to the section “TURNING OFF PROJECTOR” on P19). If projector is turned off in the wrong steps, On Start function does not operate properly.

Time left until Lamp off.

Press SELECT button at this icon to display other items.

Lamp mode

When selecting the "" (Eco), the projector reduce the brightness and set into the low power consumption mode.

Remote control

This projector has eight different remote control codes; the factory- set normal code (Code 1) and the other seven codes (Code 2 to Code 8). This switching function prevents remote control operation mixture (jam) when operating several projectors or video equipment together.

For example operating projector in “Code 7,” both projector and Remote Control Unit must be switched to “Code 7.”

To change the code of Projector;

On

On

Code 1

Remote control

On

On

Press SELECT button at this icon to display previous items.

Move the pointer to the item and then press POINT LEFT/RIGHT button(s).

When pressing SELECT button at Remote control, Remote control code Menu appears.

To change the Remote control code of the projector used in ON- SCREEN MENU is selectable from Code 1 to Code 8.

To change the code of the Remote Control Unit;

To change the remote control code of the Remote Control Unit, set the DIP switches 1-3 inside the battery compartment box of the Remote Control Unit. (Refer to P14.)

Lamp counter reset

This function is used to reset Lamp Replace Counter. When replacing Projection Lamp, reset Lamp Replace Counter by using this function. Refer to page 38 for operation.

Code 1

37

Image 37
Contents Model PLC-XT10 PLC-XT15 To the Owner Voor de klanten in Nederland Safety InstructionsFederal Communication Commission Notice CompliancesTable of Contents Compact Design Features and DesignName of Each Part of Projector PreparationHOT AIR Exhausted Connecting AC Power Cord SETTING-UP ProjectorFor Continental Europe For the U.K Room Light Preparation Positioning ProjectorMoving Projector Preparation Adjustable FeetUSB Connector Series B Connecting ProjectorTerminals of Projector Monitor OutputConnecting Projector Connecting to ComputerTerminals ProjectorAudio Video Connecting to Video EquipmentInside the Battery Compartment BOX Operation of Remote ControlBefore Operation Laser Pointer FunctionTimer Button Point Volume + ButtonsZoom Button Select ButtonLamp Replace Indicator TOP Controls and IndicatorsOperating ON-SCREEN Menu HOW to Operate ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Guide Window Before Operation Menu BARSound Menu Turning on / OFF Projector Basic OperationTurning on Projector Turning OFF ProjectorZoom Adjustment Adjusting ScreenFocus Adjustment Lens Shift AdjustmentSound Adjustment Selecting Input Source Computer InputRGB Auto Selecting Computer SystemPC System Menu Resolution Computer Input Compatible Computer SpecificationsXGA Auto PC Adjustment PC AdjustmentPC Adjust Menu Auto PC AdjComputer Input Manual PC Adjustment Display area H Display areaFull screen Image Level Select Direct Picture Image AdjustmentsImage Level Select Menu Image 1~4Image Adjust Menu Computer Input Image Level AdjustmentScreen Menu Picture Screen AdjustmentVideo Video InputVideo Selecting Video System Component Video Signal FormatPAL / Secam / Ntsc / NTSC4.43 / PAL-M / PAL-N AV System Menu Video or S-VIDEOCinema Video Input Image Level Adjustment Provides image at a normal video aspect ratio of 4 Setting Menu SettingSetting Menu To change the code of Projector To change the code of the Remote Control UnitAppendix Lamp ReplacementLamp Replace Appendix Lamp Replace Counter Lamp Handling PrecautionsInstallation Operating Wireless MouseOperating Wireless Mouse AIR Filter Care and Cleaning MaintenanceCleaning Projection Lens RecommendationTroubleshooting Wireless Mouse Remote Control UnitDoes not work Function does notTechnical Specifications Control Port Connector Appendix Configurations of TerminalsUSB Connector Series B Computer INPUT-1 and Monitor OUT Terminals AnalogOptional Parts Page Part No 301 9765 1AA6P1P3587-- MC3A