Sanyo PLC-XT10, PLC-XT15 owner manual Compliances, Federal Communication Commission Notice

Page 4

COMPLIANCES

Federal Communication Commission Notice

Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures :

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.

Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment.

Model Numbers

: PLC-XT10, PLC-XT15

Trade Name

: Sanyo

Responsible party

: SANYO FISHER COMPANY

Address

: 21605 Plummer Street, Chatsworth, California 91311

Telephone No.

: (818)998-7322

AC POWER CORD REQUIREMENT

The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.

AC Power Cord for the United States and Canada :

AC Power Cord used in the United States and Canada is listed by the Underwriters Laboratories (UL) and certified by the Canadian Standard Association (CSA).

AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be

unable to insert the plug into the outlet, contact your electrician.

GROUND

 

AC Power Cord for the United Kingdom :

This cord is already fitted with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of the plug. Should the fuse need to be replaced, an ASTA approved BS 1362 fuse must be used of the same rating, marked thus ASA . If the fuse cover is detachable, never use the plug with the cover omitted. If a replacement fuse cover is required, ensure it is of the same colour as that visible on the pin face of the plug (i.e. red or orange). Fuse covers are available from the Parts Department indicated in your User Instructions.

If the plug supplied is not suitable for your socket outlet, it should be cut off and destroyed. The end of the flexible cord should be suitably prepared and the correct plug fitted. (See Over)

WARNING : A PLUG WITH BARED FLEXIBLE CORD IS HAZARDOUS IF ENGAGED IN A LIVE SOCKET OUTLET.

The Wires in this mains lead are coloured in accordance with the following code:

Green-and-yellow ············Earth

Blue ·································Neutral

Brown ······························Live

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:

The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or coloured green or green-and-yellow.

The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

WARNING : THIS APPARATUS MUST BE EARTHED.

THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.

4

Image 4
Contents Model PLC-XT10 PLC-XT15 To the Owner Safety Instructions Voor de klanten in NederlandCompliances Federal Communication Commission NoticeTable of Contents Features and Design Compact DesignName of Each Part of Projector PreparationHOT AIR Exhausted Connecting AC Power Cord SETTING-UP ProjectorFor Continental Europe For the U.K Preparation Positioning Projector Room LightPreparation Adjustable Feet Moving ProjectorConnecting Projector USB Connector Series BTerminals of Projector Monitor OutputConnecting to Computer Connecting ProjectorTerminals ProjectorConnecting to Video Equipment Audio VideoOperation of Remote Control Inside the Battery Compartment BOXBefore Operation Laser Pointer FunctionPoint Volume + Buttons Timer ButtonZoom Button Select ButtonTOP Controls and Indicators Lamp Replace IndicatorOperating ON-SCREEN Menu HOW to Operate ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Guide Window Before Operation Menu BARSound Menu Basic Operation Turning on / OFF ProjectorTurning on Projector Turning OFF ProjectorAdjusting Screen Zoom AdjustmentFocus Adjustment Lens Shift AdjustmentSound Adjustment Selecting Input Source Computer InputRGB Auto Selecting Computer SystemPC System Menu Resolution Computer Input Compatible Computer SpecificationsXGA PC Adjustment Auto PC AdjustmentPC Adjust Menu Auto PC AdjComputer Input Manual PC Adjustment Display area H Display areaFull screen Picture Image Adjustments Image Level Select DirectImage Level Select Menu Image 1~4Computer Input Image Level Adjustment Image Adjust MenuPicture Screen Adjustment Screen MenuVideo Video InputVideo Component Video Signal Format Selecting Video SystemPAL / Secam / Ntsc / NTSC4.43 / PAL-M / PAL-N AV System Menu Video or S-VIDEOCinema Video Input Image Level Adjustment Provides image at a normal video aspect ratio of 4 Setting Menu SettingSetting Menu To change the code of the Remote Control Unit To change the code of ProjectorAppendix Lamp ReplacementLamp Replace Lamp Handling Precautions Appendix Lamp Replace CounterInstallation Operating Wireless MouseOperating Wireless Mouse Maintenance AIR Filter Care and CleaningCleaning Projection Lens RecommendationTroubleshooting Remote Control Unit Wireless MouseDoes not work Function does notTechnical Specifications Appendix Configurations of Terminals Control Port ConnectorUSB Connector Series B Computer INPUT-1 and Monitor OUT Terminals AnalogOptional Parts Page Part No 301 9765 1AA6P1P3587-- MC3A