Sanyo PLC-XW56 owner manual Compliance, Federal Communications Commission Notice

Page 7

Compliance

Federal Communications Commission Notice

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.

Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment.

Model Number

: PLC-XW56

Trade Name

: Sanyo

Responsible party

: SANYO FISHER COMPANY

Address

: 21605 Plummer Street, Chatsworth, California 91311

Telephone No.

: (818)998-7322

AC Power Cord Requirement

The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.

AC Power Cord for the United States and Canada:

AC Power Cord used in the United States and Canada is listed by the Underwriters Laboratories (UL) and certified by the Canadian Standard Association (CSA).

AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the plug will fit into the power outlet. Do not try to defeat this safety feature. Should

you be unable to insert the plug into the outlet, contact your electrician.GROUND

AC Power Cord for the United Kingdom:

This cord is already fitted with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of the plug. Should the fuse need to be replaced, an ASTA approved BS 1362 fuse must be used of the same rating, marked thus ASA . If the fuse cover is detachable, never use the plug with the cover omitted. If a replacement fuse cover is required, ensure it is of the same colour as that visible on the pin face of the plug (i.e. red or orange). Fuse covers are available from the Parts Department indicated in your User Instructions. If the plug supplied is not suitable for your socket outlet, it should be cut off and destroyed.

The end of the flexible cord should be suitably prepared and the correct plug fitted.

WARNING : A PLUG WITH BARED FLEXIBLE CORD IS HAZARDOUS IF ENGAGED IN A LIVE SOCKET OUTLET..

The Wires in this mains lead are coloured in accordance with the following code: Green-and-yellow . . . Earth

Blue . . . . . . . . Neutral Brown . . . . . . . . Live

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:

The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or coloured green or green-and-yellow.

The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.

The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

WARNING: THIS APPARATUS MUST BE EARTHED..

THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE..

Image 7
Contents Multimedia Projector Model PLC-XW56 Features and Design Table of Contents Risk of Electric Shock Do not Open To the OwnerSafety Instructions Air Circulation Installing the Projector in Proper PositionMoving the Projector Federal Communications Commission Notice ComplianceBottom Part Names and FunctionsFront Back② Computer in /S-VIDEO in /COMPONENT Rear TerminalTop Control Remote Control Operating Range Remote Control Battery Installation Note InstallationAdjustable Foot Positioning the ProjectorProjector side AC outlet side Connecting the AC Power CordCables used for connection Connecting to a ComputerConnecting to Video Equipment Connecting to Component Video Equipment PIN Code Input Dialog Box Selected Input Source and Lamp ModeBasic Operation Turning On the ProjectorTurning Off the Projector On-Screen Menu How to Operate the On-Screen MenuRemote Control Top ControlMenu Bar Keystone Correction Zoom and Focus AdjustmentRemote Control Operation Sound AdjustmentNo Show button Timer buttonAuto PC button Zoom buttonsSource Select Menu Computer InputInput Source Selection Direct OperationSelecting Computer System Manually Computer System SelectionPC System Menu Menu Operation Auto PC Adj Auto PC AdjustmentTo store adjustment parameters PC Adjust MenuManual PC Adjustment To store adjusted data ResetMode free To clear adjusted dataImage Level Selection Image Level Adjustment Wide Screen Size AdjustmentNormal TrueDigital zoom + For zooming in and out the imagesDigital zoom Input Source Selection Video Video InputDirect Operation Top Control Input Source Selection S-Video, Component, RGB Scart 21-pinAV System Menu Component Video System SelectionAuto AV System Menu Video or S-VideoImage 1~4 CinemaTint ColorProgressive Noise reductionProvide the image at a normal video aspect ratio Setting SettingDisplay Logo Logo and Logo PIN code lock settingsLogo select Logo PIN code lock CaptureTo Enter the Logo PIN code Ceiling Rear  Note CeilingRear Input searchPower management On start On start Remote controlLamp control Key lock Security Key lock and PIN code lock settingsPIN code lock Change the PIN code Change the PIN code lock settingFan Factory defaultLamp counter  Note Then check the matters below Maintenance and CleaningAttaching the Lens Cover Cleaning the Air FiltersCleaning the Projector Cabinet Cleaning the Projection LensReset the lamp replacement counter Lamp ReplacementLamp Replacement Counter Lamp Handling PrecautionsAppendix TroubleshootingAppendix Menu Tree Image AdjustAppendix Video Input Indicators Indicators and Projector ConditionON-SCREEN Resolution Compatible Computer SpecificationsMechanical Information Technical SpecificationsOptional Parts Terminal Analog RGB Mini D-sub 15 pin Configurations of TerminalsTerminal Mini DIN 8-PIN PIN Code Number Memo Lamp Replacement LabelDimensions
Related manuals
Manual 66 pages 38.4 Kb