Sanyo PLC-WXU700 owner manual Maintenance and Cleaning Lamp Replacement, Service Parts No. 333

Page 67

Maintenance and Cleaning

Lamp Replacement

When the projection lamp of the projector reaches its end of life, the Lamp replacement icon appears on the screen and LAMP REPLACE indicator lights yellow. Replace the lamp with a new one promptly. The timing when the LAMP REPLACE indicator should light is depending on the lamp mode.

WARNING:

TURN OFF THE UV LAMP BEFORE

OPENING THE LAMP COVER

Note:

The Lamp replacement icon will not appear when the Display function is set to Off (p.49), during "Freeze" (p.28), or "No show" (p.29).

Top Control

LAMP REPLACE indicator

Lamp replacement icon

CAUTION

Allow a projector to cool for at least 45 minutes before you open the Lamp Cover. The inside of the projector can become very hot.

CAUTION

For continued safety, replace with a lamp of the same type. Do not drop a lamp or touch a glass bulb! The glass can shatter and may cause injury.

Follow these steps to replace the lamp.

1

Turn off the projector and unplug the AC power cord.

Let the projector cool for at least 45 minutes.

2

Remove the screw and open the lamp cover.

3

Loosen the two (2) screws that secure the lamp. Lift

the lamp out of the projector by using the handle.

4

Replace the lamp with a new one and secure the two

 

(2) screws. Make sure that the lamp is set properly.

 

Close the lamp cover and secure the screw.

5

Connect the AC power cord to the projector and turn

on the projector.

6

Reset the lamp counter..

See “Resetting the Lamp Counter” on the next page.

Press here and pull upward. Lamp Cover

Screw

Screw

Handle

Screw

Lamp

ORDER REPLACEMENT LAMP

Replacement lamp can be ordered through your dealer. When ordering a projection lamp, give the following information to the dealer.

Model No.. of your projector

: PLC-WXU700

Replacement Lamp Type No.

: POA-LMP111

 

 

(Service Parts No.. 610 333 9740)

67

Image 67
Contents Memory Viewer Network SupportedFeatures and Design Table of Contents To the Owner Safety PrecautionSafety Instructions Moving the Projector Safety Instructions Air CirculationBottom Front Downward Upward Usual Positioning PrecautionsAC Power Cord for the United Kingdom AC Power Cord for the United States and CanadaCompliance Bottom Part Names and Functions⑦ LAN Connection Terminal ⑧ USB Connector Series a ② USB Connector Series BPart Names and Functions ⑩ Lamp Replace indicator ② Point Volume +/- buttons④ Auto SETUP/CANCEL button ⑤ Power indicator ⑥ Warning indicatorNote Part Names and Functions Remote ControlRemote Control Code Remote Control Operating RangePointer Part Names and Functions Laser Pointer FunctionPointer Function SpotlightClick button Part Names and Functions Wireless Mouse OperationAdjustable Feet ButtonPositioning the Projector InstallationCables used for connection Installation Connecting to a ComputerInstallation Connecting to Video Equipment Installation Connecting to Component Video Equipment For the U..S..A.. and Canada Installation Connecting the AC Power CordProjector side AC outlet side For Continental Europe For the U..KSelected Input Source and Lamp Control Input signal guidance windowBasic Operation Turning On the ProjectorPIN Code Input Dialog Box Basic OperationBasic Operation Turning Off the Projector On-Screen Menu Basic Operation How to Operate the On-Screen MenuRemote Control Top ControlBasic Operation Menu Bar Auto Setup Function Basic Operation Zoom and Focus AdjustmentKeystone Correction Mute Basic Operation Sound AdjustmentVolume Volume Dialog BoxBasic Operation Remote Control Operation Screen button Timer buttonNo Show button Image buttonInput Menu Computer InputInput Menu Computer Input Input Source Selection Computer 2 RGBInput button Computer Computer 2  PC System Menu pp.34-35 Auto ModeComputer Input Computer System Selection PC System MenuAuto PC adj Computer Input Auto PC adjustmentPC adjust Menu To store adjustment parametersComputer Input Manual PC adjustment Store ResetMode free Computer InputImage Select Menu Computer Input Image Mode SelectionImage Adjust Menu Computer Input Image AdjustmentTrue Screen Size AdjustmentScreen Menu NormalDigital zoom CustomPosition H/V For zooming in and out the images Digital zoom +Video button Video InputInput Source Selection Video, S-video VideoComputer button ComponentRGB Scart Hdmi buttonComponent Video Input Video System SelectionVideo or S-video AV System Menu Video or S-videoDynamic Image Select Menu Video Input Image Mode SelectionCinema Blackboard or Colorboard Video Input Image AdjustmentColor TintNoise reduction Off Disabled Lower reduction Higher reduction ProgressiveVideo Input Store MenuNatural wide Video Input Screen Size AdjustmentZoom WideLanguage SettingSetting Setting MenuAuto Keystone Auto setupAuto setup Input searchDisplay Power off? p.23Keystone BackgroundDefault Logo PIN code lock CaptureLogo PIN code lock CaptureLogo PIN code change Change the Logo PIN code lock settingEnter a Logo PIN code Change the Logo PIN codeHdmi setup Large , Middle or Small , Arrow , Finger or Dot and press Standby modeOperation of the Sub picture Switching of the Input SourcePicture in Picture Selecting the Main picture or Sub picturePower management Closed caption On startTo change the code for the projector Remote controlTo change the code for the remote control Lamp controlPIN code lock Key lockSecurity Key lock and PIN code lock Key lockPIN code change Change the PIN code lock settingEnter a PIN code Change the PIN code Enter a PIN codeLamp counter Fan Control SettingFan Fan controlFilter counter Factory defaultFactory default Filter counterInput Source Information Display InformationProjector is shut down and the Warning Maintenance and CleaningIndicator is blinking red Projector is shut down and the Warning indicator lights redResetting the Filter Counter Maintenance and Cleaning Cleaning the FiltersFilter counter Reset? Cleaning the Projection Lens Maintenance and Cleaning Attaching the Lens CapCleaning the Projector Cabinet Lamp Replace indicator Maintenance and Cleaning Lamp ReplacementService Parts No. 333 Reset the lamp counterLamp counter Reset? Maintenance and Cleaning Resetting the Lamp CounterAppendix TroubleshootingAppendix Image is distorted or runs off Remote Control does not workIndicator blinks or lights Wireless Mouse function does not workAppendix Appendix Menu Tree Image Adjust Screen System AutoSettingInformation Indicators Appendix Indicators and Projector ConditionON-SCREEN Resolution Appendix Compatible Computer SpecificationsSXGA1 Appendix List of Picture in Picture Appendix Technical Specifications Optional Parts Appendix PJ Link Notice USB Connector Series B Appendix Configurations of TerminalsHdmi 19 Pin Type a USB Thumb Drive Case Appendix PIN Code Number MemoPIN Code Lock No Logo PIN Code Lock NoAppendix Dimensions KY7AC

PLC-WXU700 specifications

The Sanyo PLC-WXU700 is a versatile and powerful projector designed to meet the demands of educational and corporate environments. As a high-performance device, it offers a blend of advanced features and technologies, making it suitable for various presentations, meetings, and classroom settings.

One of the main features of the PLC-WXU700 is its exceptional brightness, boasting an impressive 7000 lumens output. This enables the projector to deliver clear and vibrant images, even in well-lit rooms. Whether you are showcasing detailed presentations, video content, or intricate graphics, the high brightness ensures that your visuals remain sharp and easily viewable for all audiences.

The projector also supports WXGA resolution (1280 x 800 pixels), providing a clear and detailed image that enhances the viewing experience. The 16:10 aspect ratio is particularly beneficial for displaying widescreen content, making it a suitable choice for multimedia presentations. The PLC-WXU700 comes equipped with a high contrast ratio that helps in producing rich and vibrant colors, ensuring that images and videos appear lifelike and engaging.

Another significant aspect of the Sanyo PLC-WXU700 is its advanced lens technology, including a powerful zoom feature. The 1.6x optical zoom allows users to adjust the image size without sacrificing quality, making it easier to fit large images into various screen sizes or distances. This flexibility is invaluable in different room configurations, enabling seamless presentation setups.

Connectivity is another area where the PLC-WXU700 excels. It is equipped with multiple input options, including HDMI, VGA, and composite video connections. This variety allows users to connect various devices, such as laptops, DVD players, and document cameras, ensuring compatibility with a wide range of hardware.

The projector's durability and reliability are enhanced with features like a long-lasting lamp life, rated at up to 4000 hours in normal mode. This extends the time between lamp replacements, reducing maintenance costs and downtime. Additionally, its lightweight and compact design make it easy to transport between locations, ideal for professionals on the go.

In terms of user-friendliness, the PLC-WXU700 incorporates intuitive controls and an easy-to-navigate menu system, allowing users to quickly adjust settings and configurations according to their needs. This design focus ensures that both novice and experienced users can operate the projector with ease.

Overall, the Sanyo PLC-WXU700 stands out as a robust and reliable projector, with high brightness, excellent resolution, versatile connectivity, and user-friendly features. It is an ideal solution for anyone seeking top-notch presentation technology for educational and professional use.