Sanyo PLC-WXU700 owner manual Appendix Indicators and Projector Condition

Page 75

Appendix

Indicators and Projector Condition

Check the indicators for projector condition.

Indicators

Projector Condition

 

WARNING

LAMP

POWER

REPLACE

 

 

red/green

red

yellow

 

 

 

 

 

 

 

 

 

 

 

 

 

The projector is off. (The AC power cord is unplugged.)

 

 

 

 

 

 

 

The projector is in stand-by mode. Press the ON/STAND-BY button

 

 

to turn on the projector.

 

 

 

 

 

 

 

The projector is operating normally.

 

 

 

 

 

 

 

 

The projector is preparing for stand-by or the projection lamp is

 

 

being cooled down. The projector cannot be turned on until cooling

 

 

 

is completed and the POWER indicator stops blinking.

 

 

 

 

 

 

 

The projector is in the Power management mode.

 

 

 

 

 

 

 

 

The temperature inside the projector is abnormally high. The

 

 

 

projector cannot be turned on. When the projector is cooled down

 

 

enough and the temperature returns to normal, the POWER

 

 

 

indicator stops blinking and the projector can be turned on. (The

 

 

 

WARNING indicator keeps blinking.)

The projector has been cooled down enough and the temperature

returns to normal. When turning on the projector, the WARNING indicator stops blinking. Check and clean the filters.

The projector detects an abnormal condition and cannot be turned on. Unplug the AC power cord and plug it again to turn on the projector. If the projector is turned off again, unplug the AC power

cord and contact the dealer or the service center for service and checkup. Do not leave the projector on. It may cause an electric shock or a fire hazard.

• • • green

• • • red

• • • off

• • • blinks green

• • • blinks red

 

When the projection lamp reaches its end of life, the LAMP REPLACE indicator lights yellow. When this indicator lights yellow, replace the projection lamp with a new one promptly.

75

Image 75
Contents Memory Viewer Network SupportedFeatures and Design Table of Contents To the Owner Safety PrecautionSafety Instructions Moving the Projector Safety Instructions Air CirculationBottom Front Downward Upward Usual Positioning PrecautionsAC Power Cord for the United States and Canada AC Power Cord for the United KingdomCompliance Bottom Part Names and Functions② USB Connector Series B ⑦ LAN Connection Terminal ⑧ USB Connector Series aPart Names and Functions ⑩ Lamp Replace indicator ② Point Volume +/- buttons④ Auto SETUP/CANCEL button ⑤ Power indicator ⑥ Warning indicatorNote Part Names and Functions Remote ControlRemote Control Code Remote Control Operating RangePointer Part Names and Functions Laser Pointer FunctionPointer Function SpotlightClick button Part Names and Functions Wireless Mouse OperationAdjustable Feet ButtonPositioning the Projector InstallationCables used for connection Installation Connecting to a ComputerInstallation Connecting to Video Equipment Installation Connecting to Component Video Equipment For the U..S..A.. and Canada Installation Connecting the AC Power CordProjector side AC outlet side For Continental Europe For the U..KSelected Input Source and Lamp Control Input signal guidance windowBasic Operation Turning On the ProjectorPIN Code Input Dialog Box Basic OperationBasic Operation Turning Off the Projector On-Screen Menu Basic Operation How to Operate the On-Screen MenuRemote Control Top ControlBasic Operation Menu Bar Basic Operation Zoom and Focus Adjustment Auto Setup FunctionKeystone Correction Mute Basic Operation Sound AdjustmentVolume Volume Dialog BoxBasic Operation Remote Control Operation Screen button Timer buttonNo Show button Image buttonInput Menu Computer InputComputer Input Input Source Selection Computer 2 RGB Input MenuInput button Computer Computer 2  PC System Menu pp.34-35 Auto ModeComputer Input Computer System Selection PC System MenuAuto PC adj Computer Input Auto PC adjustmentPC adjust Menu To store adjustment parametersComputer Input Manual PC adjustment Store ResetMode free Computer InputImage Select Menu Computer Input Image Mode SelectionImage Adjust Menu Computer Input Image AdjustmentTrue Screen Size AdjustmentScreen Menu NormalDigital zoom CustomPosition H/V For zooming in and out the images Digital zoom +Video button Video InputInput Source Selection Video, S-video VideoComputer button ComponentRGB Scart Hdmi buttonComponent Video Input Video System SelectionVideo or S-video AV System Menu Video or S-videoVideo Input Image Mode Selection Dynamic Image Select MenuCinema Blackboard or Colorboard Video Input Image AdjustmentColor TintNoise reduction Off Disabled Lower reduction Higher reduction ProgressiveVideo Input Store MenuNatural wide Video Input Screen Size AdjustmentZoom WideLanguage SettingSetting Setting MenuAuto Keystone Auto setupAuto setup Input searchDisplay Power off? p.23Keystone BackgroundDefault Logo PIN code lock CaptureLogo PIN code lock CaptureLogo PIN code change Change the Logo PIN code lock settingEnter a Logo PIN code Change the Logo PIN codeHdmi setup Large , Middle or Small , Arrow , Finger or Dot and press Standby modeOperation of the Sub picture Switching of the Input SourcePicture in Picture Selecting the Main picture or Sub picturePower management Closed caption On startTo change the code for the projector Remote controlTo change the code for the remote control Lamp controlPIN code lock Key lockSecurity Key lock and PIN code lock Key lockPIN code change Change the PIN code lock settingEnter a PIN code Change the PIN code Enter a PIN codeLamp counter Fan Control SettingFan Fan controlFilter counter Factory defaultFactory default Filter counterInput Source Information Display InformationProjector is shut down and the Warning Maintenance and CleaningIndicator is blinking red Projector is shut down and the Warning indicator lights redMaintenance and Cleaning Cleaning the Filters Resetting the Filter CounterFilter counter Reset? Maintenance and Cleaning Attaching the Lens Cap Cleaning the Projection LensCleaning the Projector Cabinet Lamp Replace indicator Maintenance and Cleaning Lamp ReplacementService Parts No. 333 Reset the lamp counterLamp counter Reset? Maintenance and Cleaning Resetting the Lamp CounterAppendix TroubleshootingAppendix Image is distorted or runs off Remote Control does not workIndicator blinks or lights Wireless Mouse function does not workAppendix Appendix Menu Tree System AutoSetting Image Adjust ScreenInformation Indicators Appendix Indicators and Projector ConditionON-SCREEN Resolution Appendix Compatible Computer SpecificationsSXGA1 Appendix List of Picture in Picture Appendix Technical Specifications Optional Parts Appendix PJ Link Notice Appendix Configurations of Terminals USB Connector Series BHdmi 19 Pin Type a USB Thumb Drive Case Appendix PIN Code Number MemoPIN Code Lock No Logo PIN Code Lock NoAppendix Dimensions KY7AC

PLC-WXU700 specifications

The Sanyo PLC-WXU700 is a versatile and powerful projector designed to meet the demands of educational and corporate environments. As a high-performance device, it offers a blend of advanced features and technologies, making it suitable for various presentations, meetings, and classroom settings.

One of the main features of the PLC-WXU700 is its exceptional brightness, boasting an impressive 7000 lumens output. This enables the projector to deliver clear and vibrant images, even in well-lit rooms. Whether you are showcasing detailed presentations, video content, or intricate graphics, the high brightness ensures that your visuals remain sharp and easily viewable for all audiences.

The projector also supports WXGA resolution (1280 x 800 pixels), providing a clear and detailed image that enhances the viewing experience. The 16:10 aspect ratio is particularly beneficial for displaying widescreen content, making it a suitable choice for multimedia presentations. The PLC-WXU700 comes equipped with a high contrast ratio that helps in producing rich and vibrant colors, ensuring that images and videos appear lifelike and engaging.

Another significant aspect of the Sanyo PLC-WXU700 is its advanced lens technology, including a powerful zoom feature. The 1.6x optical zoom allows users to adjust the image size without sacrificing quality, making it easier to fit large images into various screen sizes or distances. This flexibility is invaluable in different room configurations, enabling seamless presentation setups.

Connectivity is another area where the PLC-WXU700 excels. It is equipped with multiple input options, including HDMI, VGA, and composite video connections. This variety allows users to connect various devices, such as laptops, DVD players, and document cameras, ensuring compatibility with a wide range of hardware.

The projector's durability and reliability are enhanced with features like a long-lasting lamp life, rated at up to 4000 hours in normal mode. This extends the time between lamp replacements, reducing maintenance costs and downtime. Additionally, its lightweight and compact design make it easy to transport between locations, ideal for professionals on the go.

In terms of user-friendliness, the PLC-WXU700 incorporates intuitive controls and an easy-to-navigate menu system, allowing users to quickly adjust settings and configurations according to their needs. This design focus ensures that both novice and experienced users can operate the projector with ease.

Overall, the Sanyo PLC-WXU700 stands out as a robust and reliable projector, with high brightness, excellent resolution, versatile connectivity, and user-friendly features. It is an ideal solution for anyone seeking top-notch presentation technology for educational and professional use.