Hitachi PJ-LC9 user manual Loading batteries into the remote control

Page 19

Preparations

Loading batteries into the remote control

To use the remote control, please load the batteries. Whenever the remote control starts to malfunction, replace the batteries. If you will not use the remote control for an extended period, remove the batteries from the remote control and store them in a safe place.

1. Remove the battery cover. Slide back and remove the battery cover in the direction of the arrow.

2. Take old batteries out and/or put new batteries in. When putting in batteries, align and insert the two AA batteries according to their plus and minus terminals as indicated in the remote control.

3. Close the battery cover. Replace the battery cover in the direction of the arrow and snap it back into place.

WARNING ►Always handle the batteries with care and use them only as directed. Improper use may result in battery explosion, cracking or leakage, which could result in fire, injury and/or pollution of the surrounding environment.

Be sure to use only the batteries specified. Do not use batteries of different types at the same time. Do not mix a new battery with used one.

Make sure the plus and minus terminals are correctly aligned when loading a battery.

Keep a battery away from children and pets.

Do not recharge, short circuit, solder or disassemble a battery.

Do not allow a battery in a fire or water. Keep batteries in a dark, cool and dry place.

Do not give the battery a physical impact.

If you observe a leakage of a battery, wipe out the liquid and then replace

a battery. If the liquid adheres to your body or clothes, rinse well with water immediately.

• Obey the local laws on disposing a battery.

ENGLISH

17

Image 19
Contents Bedienungsanleitung Benutzerhandbuch ProjectorUser’s Manual Operating Guide Manuel dutilisation Guide dutilisationDeutsch Bedienungsanleitung Zusätzlicher Français Manuel dutilisation SupplémentaireEspañol Manual de usuario Adicional Trademark acknowledgment Thank you for purchasing this projectorPreparations Power on/offTurning on the power Turning off the power Before useWarranty and after-service Specifications Multifunctional settingsMaintenance TroubleshootingAbout this manual Projector featuresAbout contents of package Projector Part namesControl buttons Remote controlMagnify Strap ring Fastening the lens coverProjector Bottom side StrapTabs About the filter cover bottom-up useArrangement When put on a table When suspended from the ceiling120 For 169 screensFor 43 screens Screen size Projection distance Screen height InchElevator feet Elevator button Adjusting the projector’s elevatorExamples of connection with a VCR/DVD player Connecting your devicesExamples of connection with a computer Vesa Example of computer signalAbout Plug-and-Play capability Vesa TextPower switch AC inlet Connecting power supplyLoading batteries into the remote control Using the remote control Button Power switch Turning on the powerSTANDBY/ON Turning off the power Temporarily muting the sound Adjusting the volumeSearching an input signal Selecting an input signalFor a 43 signal For a 169 signalSelecting an aspect ratio Adjusting the focus Adjusting the zoom magnifying powerUsing the automatic adjustment feature Correcting the keystone distortions Adjusting the positionFreezing the screen Using the partial magnify featureTemporarily blanking the screen To display a menu Using the menu functionTo choose the target menu To choose the target item Setup MenuEnter To close the menu To resetTo operate To return to the previous menuMode AspectZoom KeystoneMirror ResetSharpness WhisperGamma #1 Default  #1 Custom  #2 Default#3 Custom  #3 Default  #2 Custom Picture menuCustom  LOW High  MiddleColor Temp SAVE4 SAVE3  SAVE2  SAVE1 TV  Film  Turn OFFProgressive LOAD1  LOAD2  LOAD3  LOAD4Image menu For a 169 signalFor a 43 signal For an RGB signalSize PhaseOver Scan PositionFor a video signal or s-video signal Auto Adjust ExecuteTurn on  Turn OFF Input menuColor Space Auto  Ntsc  PAL  SecamNormal  Hinvert  Vinvert  H&VINVERT Setup menuVolume Normal  WhisperBright  Dark Screen menuMenu Position OSD BrightStart UP Sync is OUT of Range MyScreen LockMessage No Input is DetectedAuto OFF Reset  CancelOption menu RGB  S-VIDEO  VideoFAN Speed ServiceAuto Adjust Enable  DisableGhost Factory ResetFilter Message Lamp Type number = DT00707 Case of replacement by yourselfCenter point of claws Tabs Filter cover for bottom-up use Air filterType number = NJ22642 Usual filter coverUsual filter cover Push markInside of the projector Caring for the cabinet and remote controlCaring for the lens Related messages There is no input signalInternal portion temperature is rising Horizontal or vertical wavelength of the input signalRegarding the indicator lamps Has become heated Indicator Cooling fan is not operatingIt is time to clean the air filter There is a possibility that the interior portionIf the situation cannot be corrected Phenomena that may easily be taken as machine defectsColor Space setting is not suitable Volume is adjusted to an extremely low levelBrightness is adjusted to an extremely low level Color settings are not correctly adjustedVideo input SpecificationRGB input Communication portUnit mm Dimension diagramHitachi Europe S.r.l Hitachi Home & Life Solutions, Inc. Middle East OfficeDigital Media Div Hitachi Europe GmbH Munich Office
Related manuals
Manual 62 pages 31.2 Kb

PJ-LC9 specifications

The Hitachi PJ-LC9 is a compact and versatile projector, renowned for its cutting-edge features and outstanding performance. Ideal for business presentations, educational settings, and home theater use, it blends functionality with user-friendly design. With its impressive specifications, the PJ-LC9 caters to the demands of professionals and casual users alike.

One of the key features of the PJ-LC9 is its native resolution of 1024 x 768 pixels (XGA), which ensures crisp and clear images. This resolution is particularly beneficial for presentations containing detailed graphs, charts, and high-quality images. The projector’s brightness of 2500 ANSI lumens makes it suitable for use in a variety of lighting conditions, allowing it to shine in both dim and well-lit environments.

The PJ-LC9 employs advanced LCD technology, which enhances color accuracy and contrast, providing vibrant and lifelike visuals. This technology aids in delivering sharp and vivid images, which is crucial for capturing and maintaining the audience's attention during presentations or watching media content.

Another standout characteristic of the PJ-LC9 is its lightweight design, weighing just 2.5 kg, which makes it highly portable. Its compact form factor allows users to effortlessly transport it between locations, making it an excellent choice for traveling professionals and educators who need to present on-the-go.

Connectivity options are another advantage of the Hitachi PJ-LC9. It comes equipped with multiple input ports, including HDMI, VGA, and USB, enabling users to connect various devices such as laptops, desktops, and media players without hassle. The inclusion of RS-232C serial connection also makes it compatible with computer control for automation and control purposes.

Additionally, the projector features a built-in 1W speaker, providing adequate sound output for small spaces, although external speakers may still be preferable for larger venues. The PJ-LC9 also supports a range of aspect ratios, including 4:3 and 16:9, allowing for flexibility depending on the content being presented.

In terms of maintenance, the PJ-LC9 utilizes a long-lasting lamp that can deliver up to 3000 hours of operation in standard mode, extending to around 5000 hours in eco mode. This longevity ensures reduced maintenance costs and downtime for users.

In summary, the Hitachi PJ-LC9 is a reliable, feature-rich projector that excels in performance and versatility. Its combination of high resolution, brightness, portability, and connectivity options make it a popular choice for professionals and educators seeking an efficient and effective projection solution.