Hitachi CP-S220W user manual Troubleshooting, OSD Message, Mssage display list, Message Contents

Page 19

TROUBLESHOOTING

OSD Message

A message like the bottom table sometimes displays it with this opportunity at the time of power source on.

Cope in accordance with the bottom table if message appears on the screen.

Table 1-8. Mssage display list.

Message

Contents

 

 

 

Left message is displayed when ramp use time is 1700 hours.

CANGE THE LAMP

The use time of the ramp draws near in the life.

A power source is turned off automatically when the use time

AFTER REPLACING LAMP,

of the ramp reaches a life.

RESET THE LAMP TIME.

Recommend the setup of the new ramp and a little early

*1)

 

switching.

 

Be sure to reset a ramp timer after the ramp switching.

 

 

CANGE THE LAMP

Left message is displayed when ramp use time passes 1779

hours.

AFTER REPLACING LAMP,

It is more ** time until the use time of the ramp reaches a life.

RESET THE LAMP TIME.

When ** time is more used, a power source is turned off

THE POWER WILL TURN OFF

automatically. Exchange a ramp in accordance with 1-17-page

AFTER ** hr.

"ReplacingtheLamp".

*1)

 

Be sure to reset a ramp timer after the ramp resetting.

CANGE THE LAMP

A power source will be turned off automatically soon because

AFTER REPLACING LAMP,

the use time of the ramp reached a life.

RESET THE LAMP TIME.

Turn off a power source soon and exchange a ramp in

THE POWER WILL

accordance with 1-17-page "ReplacingtheLamp".

TURN OFF

Be sure to exchange a ramp and reset a ramp timer after the

AFTER 0 hr.

switching.

 

 

NO INPUT IS DETECTED

There is no signal input

Verification is to give me the condition of the connection of

ON ***

input of a signal and the signal source.

 

 

 

 

The current horizontal or vertical frequency cannot be used by

SYNC IS OUT OF RANGE

this projector

ON ***

Verification is to give me the specification of this opportunity

 

and the signal source.

 

 

 

Internal overheating.

 

Wait approximately 20 min. and then turn the power on again.

CHECK THE AIR FLOW

* Make sure the ventilation openings are not blocked.

 

* Clean the air filter.

 

* Lower the ambient temperature to 35 degrees C or less.

 

 

*1) This display will disappear after 3min. but will reappear when the power is turned on again.

ENGLISH

1-19

Image 19
Contents Contents Contents of package FeaturesBefore USE Part Names Before USEReplacing Loading the BatteryVolume First LoadingInstallation Reference InstallationInstallation of the Projector and Screen Angle AdjustmentPower Connection InstallationCabling Plug & Play Example of system setupOperations Power On/OffPower On Power OffBasic Operation OperationsBasic Operation Description Normal menu Single menu Volume adjustment Reduce VolumeSet/Clear Mute mode Press the Mute Automatic adjustment at VIDEO/S-VIDEO inputSetup Menu Description Setup MenuSelect Execuet with the button Select video signal typeInput Menu Input MenuImage Menu Image MenuSelect menu display language Select with Options MenuOptions Menu Select menu background color Select withNo Signal Menu No Signal MenuLamp Life MaintenanceElectric shock High temperature Mechanical shock LampsResetting the Lamp Timer MaintenanceReplacing the Lamp Maintenance of the lens Air Filter MaintenanceOther Maintenance Inside maintenanceMssage display list TroubleshootingMessage Contents OSD MessageIndicator TroubleshootingIndicators Message Indicators Message list10. Symptom SymptomSymptom Possible cause Remedy Specifcations 11. SpecificationsAudio Dimension Diagram Warranty and AFTER-SERVICESpecifcations FCC Statement Warning Regulatory NoticesFor the Customers in Canada Technical Example of computer signalTechnical Initial set signals