Hitachi CP-S420WA/CP-X430WA/CP-X430W, CP-S420/CP-X430 Symptom Possible cause Remedy, 11,15

Page 23

TROUBLESHOOTING (continued)

Symptom

Before requesting repair, check in accordance with the following chart. If the situation cannot be corrected, then contact your dealer.

Table 11. Symptom

Symptom

Possible cause

Remedy

 

Page

 

 

 

 

 

 

 

The main power switch is not

Turn on the main power switch.

 

 

turned on.

 

 

 

 

 

8,9

 

 

 

 

 

 

The power cord is

Plug the power cord into an AC

 

 

The power is not

disconnected.

power outlet.

 

 

 

 

 

 

 

 

turned on.

 

Turn off the projector with the main

 

 

The main power was

power switch (set the power switch

9

 

disconnected during operation

to [O]), and wait for about 20

 

 

by the power failure and so on.

minutes. When the equipment has

 

 

 

cooled enough, turn power on.

 

 

 

 

 

 

The input is not correctly set.

Use the projector or remote control

10

No video or audio.

 

 

 

 

 

No signal input.

Connect correctly.

 

 

7,8

 

 

 

 

 

 

 

 

 

 

The projector is not correctly

Connect correctly.

 

 

7,8

 

connected.

 

 

 

 

 

 

 

 

 

 

 

 

Video is present but

The volume is set to minimum.

Press VOLUME

on the remote

11,15

control or display the menu screen

no audio.

 

and adjust the volume.

 

 

 

 

 

 

 

 

 

 

 

 

 

Mute is turned on.

Press the MUTE

button.

 

11

 

 

 

 

 

 

 

The projector is not correctly

Connect correctly.

 

 

7,8

 

connected.

 

 

 

 

 

 

 

Audio is present but

 

 

 

The brightness adjustment knob

Select BRIGHT with the MENU

12

no video.

is rotated fully clockwise.

button and the press the

button.

 

 

 

 

 

 

 

The lens cap is still attached.

Remove the lens cap.

 

9

 

 

 

 

 

 

Colors are pale and

Color density and color

Adjust the video.

 

 

12

color matching is

matching are not correctly

 

 

 

 

 

 

 

 

 

 

 

 

 

Brightness and contrast are not

Adjust the video.

 

 

12

 

correctly adjusted.

 

 

 

 

 

 

 

 

 

 

 

 

 

Images are dark.

The lamp is nearing the end of

Replace with a new lamp.

 

17

its service life.

 

 

 

 

 

 

 

 

 

 

 

 

WHISPER mode is set.

Clear WHISPER mode.

 

15

 

 

 

 

 

 

Video is blurred.

Focus or H PHASE is out of

Adjust the focus or H PHASE.

9,12

adjustment.

 

 

 

 

 

 

 

 

 

 

 

ENGLISH-22

Downloaded from www.Manualslib.com manuals search engine

Image 23
Contents CP-S420WA/CP-X430WA/CP-X430W CP-S420/CP-X430Contents Before USE FeaturesContents of Package Component Video Before USEPart Names U T I O N Refer to P.9 OperationsLoading the Batteries Installation Reference InstallationInstallation of the Projector and Screen Angle AdjustmentCabling InstallationCabling Plug & Play Power ConnectionExample of System Setup Standby Power onPower OFF OperationsBasic Operation Description OperationsBasic Operation Menu Display Start/Stop Press the Menu button Select Mode of P.IN P. Display Press the PinP buttonNormal menu Single menu Setup Menu Setup MenuInput Menu Automatic Adjustment at RGB Input Select the Execute withAutomatic Adjustment at Video Input Select the Execute with Input MenuMirror Image MenuImage Menu Start UPSelect Menu Background Color Select with the / button Options MenuOptions Menu Reduce Increase No Signal MenuNo Signal Menu Description Lamp Life MaintenanceLamp Replacing the Lamp MaintenanceResetting the Lamp Timer Air Filter Other MaintenanceOSD Message TroubleshootingMessage Contents OSD MessageIndicator TroubleshootingIndicators Message Indicators Message11,15 SymptomSymptom Symptom Possible cause RemedySpecifications SpecificationsWarranty and AFTER-SERVICE Technical Dimension DiagramSignal Connector Pin Assignment Technical Example of computer signalInitial set signals PS/2 Mouse Connection to the Mouse ControlPS/2, ADB or Serial Mouse USB MouseSerial Mouse ADB MouseProtocol Communications settingCommand data RS-232C communicationIncreasing the projector setting value Increment command Requesting projector status Get commandChanging the projector settings Set command Using the projector default settings Reset CommandCRC Be EF BA D2 Be EF FD D3 Be EF Ntsc PAL Be EF CB D0 For the Customers in Canada Pour les utilisateurs au Canada Regulatory NoticesFCC Statement Warning Hitachi Europe AB Hitachi Europe, Digital Media GroupHitachi Europe S.r.1, Digital Media Group Hitachi Europe GmbH, Digital Media Group