Hitachi CP-x950E, CP-X950W specifications When you think something wrong, Indicator display

Page 29

Indicator display

The ON indicator, LAMP indicator and TEMP indicator will light or blink in the following cases.

 

Indicator status

Meaning

Remedy

 

 

 

 

 

Lights orange

Standby mode

—————————————

 

 

 

 

 

Blinks green

During warming up

—————————————

ON indicator

 

 

 

Lights green

During operation

—————————————

 

 

 

 

 

Blinks orange

During cooling down

—————————————

 

 

 

 

 

Lights red

Under the mode

Under the method

 

 

 

 

LAMP indicator

Lights red

Lamp cannot light

Cool projector by power off for 20 minutes.

 

 

 

 

TEMP indicator

Lights red

Temperature inside too high

Correctly reinstall so as not to block ventilation holes.

 

 

 

Blinks red

Cooling fan accidented

Call a maintenance person.

 

 

 

 

 

When the LAMP indicator lights, turn the power off. If the problem cannot be recovered, contact your dealer.

When you think something wrong

Check the following again before asking for service.

If the trouble cannot be recovered, consult your dealer.

Phenomena

Cause

Check point

Page

 

 

 

 

Power cannot be turned

•The Main power is not turned on.

•Turn the MAIN POWER switch on.

P12

on.

•The power cord is disconnected.

•Insert the power cord into an AC socket.

P8

 

 

 

 

 

No picture and sound

•The setting of the input source is not

•Set the correct input using the input select

P8, P9

 

correct.

button of the projector or the remote

P12, P16

 

 

control.

 

 

•Wiring to the projector is not correct.

•Connect the cable correctly.

P8, P27

 

 

 

 

Only picture is displayed

•Wiring to the projector is not correct.

•Connect the cable correctly.

P8, P27

with no sound

•The volume is set to minimum.

•Press the VOL button or press the MENU

P9

 

 

•The unit enters the mute mode.

button and adjust the volume.

P8, P9

 

•Press the MUTE button.

 

 

 

 

 

 

 

Only sound is heard

•Wiring to the projector is not correct.

•Connect the cable correctly.

P8, P27

without a picture

•The brightness is set fully to the dark side.

•Press the MENU button and select

P15

 

 

 

BRIGHT and press the button.

 

 

 

•Turn the lens cover lever down and lens

 

 

 

cover opens.

 

 

 

 

 

Color is weak and tint is

The color and tint have been adjusted

Adjust the color and tint correctly.

P15

incorrect

incorrectly.

 

 

 

 

 

 

Picture is dark

•The brightness and contrast has been

•Adjust the brightness and contrast

P15

 

adjusted incorrectly.

correctly.

 

 

•The lamp has not been adjusted.

•Replace the lamp with a new one.

P28

 

 

 

 

Picture is not clear

Focus or H.PHASE is not matched.

Adjust the focus or H.PHASE.

P12, P15

 

 

 

 

LAMP indicator lights red.

Trouble with the lamp.

Turn off the power and leave for 20 minutes ;

P29

 

 

then turn the power on again.

 

 

 

 

 

TEMP indicator lights red.

Inside the projector too hot.

•Do not block the venational holes.

P6, P29

 

 

•Clean the air filter.

 

 

 

•Use the projector under 35˚C

 

 

 

temperature.

 

 

 

 

 

Abrightdotmaybeseeninthepict re Thisis aphenomenonpec liartotheliq idcrystalandisnot aproblem

29

Image 29
Contents Contents FeaturesOutline Operating GuideFor the Customers in U.K Power cord Video signal cablesBefore use Video inputsDo not install this unit in an unstable Do not look directly at the lens when the lamp is litDo not use power supplies If any abnormality occursDo not stare directly into the laser Aperture Be careful in handling the power cordCleaning Handle the power cord carefullyClean inside the unit at least once two years When you are not going to use for a long timeVolume Do not place this unit where it gets hotCleaning the lens Cleaning the cabinetStandby / on Names and functions of each partMain unit Disk PAD Remote control transmitterLaser on Names and functions of each part ¡ Remove the battery Compartment coverInstallation of liquid crystal projector InstallationView from the top View from the side View from the front View from the sideTurn the Main Power switch of the projector on. I on Press the STANDBY/ON button, for 1 second Basic operationsPlug & Play Press the Menu buttons or the Menu on / OFF button Adjustments and functionsBrightness SET UPColor SizeImage InputReveal OPT. OptionBlank COM. Bits LanguageConnection to the RGB signal terminal Connection to the video signal terminalsExample of computer signal Connection to the RGB signal terminalInitial set signals Connection to the RGB signal terminalMouse emulation Connection to the control signal terminalControl signal terminal Connection to the control signal terminal Communication Control command codeControl data table Procedure of getting the Projector status Connecting various equipment Example of system setupCleaning the air filter Re-install the air filter Clean the air filter using a vacuum cleanerLamp Message tableIndicator display When you think something wrongDimension diagram

CP-X950W, CP-x950E specifications

The Hitachi CP-X950E and CP-X950W are versatile projectors designed for a wide array of applications, ranging from corporate environments to educational institutions. Offering a blend of high performance and user-friendly features, these projectors are noted for their outstanding image quality and advanced technologies.

One of the primary features of the CP-X950E and CP-X950W is their impressive brightness, with a high lumen output that ensures clear, vibrant images even in well-lit environments. This makes them suitable for both large and small venues, where visibility and clarity are paramount. The projectors also support WXGA resolution (1280 x 800), providing sharp and detailed images that enhance presentations and visual displays.

Another significant characteristic of these projectors is their use of 3LCD technology. This innovative technology ensures excellent color accuracy and brightness uniformity, resulting in natural-looking images with rich colors. The vivid color reproduction makes these projectors ideal for displaying presentations, videos, and detailed graphics.

The CP-X950E and CP-X950W also incorporate advanced connectivity options, including HDMI, VGA, and USB ports, allowing users to connect various devices such as laptops, tablets, and smartphones with ease. This flexibility is complemented by a built-in 10-watt speaker, offering quality audio without needing external sound systems, thus making them perfect for presentations and lectures.

For users concerned with ease of use, the projectors feature an intuitive interface and remote control, simplifying operation in any setting. They also boast a long lamp life, significantly reducing maintenance costs and ensuring reliable performance over time.

In terms of portability, the CP-X950E and CP-X950W are relatively lightweight and compact, making them easy to transport between different locations. Their robust design ensures reliability in various environments, making them a favored choice among educators and business professionals alike.

With a combination of high brightness, 3LCD technology, and user-friendly features, the Hitachi CP-X950E and CP-X950W projectors are well-suited for engaging presentations and effective visual communication. Their versatility and innovation position them as excellent tools in both educational institutions and corporate settings, enabling users to deliver impactful messages with confidence.