Hitachi CPX385W Using the Remote Control, Putting batteries into the remote control unit

Page 14
approximately 3 meters
approximately 3 meters

USING THE REMOTE CONTROL

Putting batteries into the remote control unit

CAUTION Precautions to observe in regards to the batteries

Always handle the batteries with care and use them only as directed. Improper use may result in battery cracking or leakage, which could result in fire, injury and/or pollution of the surrounding environment.

Keep the battery away from children and pets.

Be sure to use only the batteries specified for use with the remote control. Do not mix new batteries with used ones.

When inserting batteries, verify that the plus and minus terminals are aligned correctly (as indicated in the remote control).

When you dispose the battery, you should obey the law in the relative area or country.

1

Remove the battery

 

2

Insert the batteries

cover

 

Align and insert the two AA

 

Push the knob while lifting

 

 

batteries (that came with the

 

up the battery cover in the

 

 

projector) according to their plus

 

direction of the arrow.

 

 

and minus terminals (as indicated

 

 

 

 

 

 

 

in the remote control).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3 Closecover the battery

Replace the battery cover in the direction of the arrow and snap it back into place.

Operating the remote control

The remote control works with both the

projector's front and rear remote sensors.

• The range of the remote sensor on the front and back is 3 meters with a 60-degree range (30 degrees to the left and right of the remote sensor).

• Since the remote control uses infrared light to send

 

30

degrees

 

30

degrees

signals to the projector (Class 1 LED), be sure to

 

 

30

 

30

 

use the remote control in an area free from

degrees

degrees

 

 

 

 

 

 

obstacles that could block the remote control's output signal to the projector.

Only use the accompanying remote control. Using other remote controls (even of similiar models) to control the CP-X385W may result in unexpected operation.

ATTENTION Precautions to observe when using the remote control

Do not drop or otherwise expose the remote control to physical impact.

Do not get the remote control wet or place it on wet objects. Doing so may result in malfunction.

Remove the batteries from the remote control and store them in a safe place if you won't be using the remote control for an extended period.

Replace the batteries whenever the remote control starts to malfunction.

When strong light, such as direct sunlight or light from an extremely close range (such as from an inverter fluorescent lamp), hits the projector's remote sensor, the remote control may cease to function. Adjust the direction of the projector to keep light from directly hitting the projector's remote sensor.

13

Image 14
Contents Manuale Distruzioni Vol.1 Informazioni di base Brukerhåndbok Vol.1 GrunnleggendeContents Transmitter Projector FeaturesPower cord Only use the power cord that came with the projector Devices you will be using to the projectorUSB Port Handle Hook Power Switch AC Inlet To the Power CordPart Names Button Search buttonSetting UP the Projector Angle AdjustmentAdjusting the Screen Size and Projection Distance If 43 aspect ratioConnecting Your Devices Ports and Cables Function Projector Port Connection CablesConnecting Your Devices Connecting to a ComputerConnecting to a DVD Player Connecting to a VCRConnecting to a Display Monitor Operating the remote control Using the Remote ControlPutting batteries into the remote control unit Turning on the Power Selecting an Input Signal Turning OFF the Power Press Buttons to adjust Volume Adjusting the VolumePress the Volume button Temporarily Muting the SoundPress the Position button Adjusting the PositionUse Buttons to adjust Position Automatic Adjustment for Video Input Using the Automatic Adjustment FeatureAutomatic Adjustment for RGB Input Press the Auto buttonAs illustrated on the right, a dialog will appear Correcting Keystone DistortionsPress the Keystone button On the screen to aid you in correctingUsing the Magnify Feature Freezing the ScreenTemporarily Blanking the Screen Signal SearchingSelecting the Aspect Ratio Select an item using Buttons, then press Or Enter button Using the Menu FunctionsSelect a menu using Buttons Then press Or Enter button Press Buttons to adjust the levelAvailable Functions Remote Control Operation Operating the PC ScreenDo not use the projector with the lamp cover removed High Voltage High Temperature High PressureLamp Lamp Replacing the lampAIR Filter Caring for the air filterReplacing the air filter Fixing the Handle HandleOther Care Bedienungsanleitung Teil 2 Fortsetzung For Technical see the end of this manual Main Menu Multifunctional SettingsMain Menu PICTURE1 Menu Picture 1 MenuPicture 2 Menu PICTURE2 MenuAuto Input MenuInput Menu VideoBlank Screen MenuScreen Menu Start UPOption Menu VolumeOption Menu Auto OFFRelated Messages Regarding the Indicator Lamps Power Lamp TempVol.2-3 Phenomena That May Easily Be Mistaken for Machine DefectsVol.2-2 Vol.2-6Specification SpecificationsDimension Diagram Unit mmWarranty and AFTER-SERVICE Page Italy