Hitachi CP-X880 Phenomena That May Easily Be Mistaken for Machine Defects, Vol.2-2, Vol.2-3

Page 11

WHAT TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED (continued)

Phenomena That May Easily Be Mistaken for Machine Defects

Before requesting repair, check in accordance with the following chart. If the situation cannot be corrected, then contact your dealer.

Phenomenon

Cases not involving a machine defect

Items to be confirmed

Reference

Page(s)

 

 

 

 

 

 

 

 

The main power source is not ON.

Turn on the main power.

Vol.1-3, 15

 

 

 

 

The electrical power cord is not plugged in.

Correctly connect the power cord.

 

 

 

 

 

 

Power does not

 

Be sure to press the “O” (power OFF) side

 

come ON

The main power source has been

of the main power switch, and leave this OFF

Vol.1-15

 

interrupted during operation, such as by

for approximately 20 minutes. After the unit

 

a power outage (blackout), etc.

has sufficiently cooled down, turn ON the

 

 

 

power source.

 

 

 

 

 

No sound or

The input changeover settings

Select the input signal, and

Vol.1-16

are mismatched.

correct the settings.

pictures are

 

 

 

 

 

 

 

outputted

No signal is being inputted.

Correctly connect the connection cord.

Vol.1-8-12

 

 

 

 

 

The electrical wiring to this unit

Correctly connect the connection cord.

Vol.1-8-12

 

is not correctly connected.

Pictures are

 

 

 

 

 

The volume setting has been set at (or

 

Vol.1-18

displayed, but no

Adjust the VOLUME setting to a higher level.

adjusted to) an extremely low level.

sounds are heard

 

 

 

 

 

The MUTE mode is the current setting.

Press the MUTE button to release

Vol.1-18

 

 

 

(change) the MUTE mode setting.

 

 

The electrical wiring to this unit

Correctly connect the connection cord.

Vol.1-8-12

Sounds are

is not correctly connected.

 

 

heard, but no

The brightness setting has been set at

Adjust the BRIGHT setting to a

Vol.2-2

pictures are

(or adjusted to) an extremely low level.

brighter level.

 

displayed

 

 

 

The lens cap has not been removed.

Remove the lens cap.

Vol.1-15

 

 

 

 

 

Colors have a faded-

 

Perform picture adjustments by changing the

Vol.2-3

out appearance

Color depth setting or color tone setting

COLOR BAL R, the COLOR BAL B, and/or the

Color tone is poor

 

TINT settings, etc.

 

 

 

 

 

 

The brightness setting and/or contrast

Perform picture adjustments by changing the

Vol.2-2

 

setting has not been properly adjusted.

BRIGHT and/or CONTRAST settings, etc.

 

Pictures appear

The WHISPER mode is the current

Change (by releasing) from the

Vol.2-7

dark

setting.

WHISPER mode.

 

 

Lamp is approaching the end of its

Exchange the old lamp with a new

Vol.1-27, 28

 

product lifetime.

lamp.

 

 

 

 

 

Pictures appear

Either the FOCUS setting or the H

Adjust the FOCUS and H PHASE settings.

Vol.1-16

blurry

PHASE is not properly adjusted.

Vol.2-3

 

 

 

 

 

Input signal changes

INPUT dial is set between the click

Turn the INPUT dial and set it at the

Vol.1-16

with no-operation.

points.

click point.

 

NOTE

Although bright spots or dark spots may appear on the screen, this is a unique characteristic of liquid crystal displays, and such do not constitute or imply a machine defect.

10

Page 10 Page 12
Image 11
Page 10 Page 12
Contents
Brukerhåndbok Vol.1 Grunnleggende CP-X880W/CP-X885WManuale Distruzioni Vol.1 Informazioni di base Contents Item selection Multifunctional SettingsMain Menu Main MenuPICTURE-2 Menu PICTURE-1 MenuPICTURE-2 Menu PICTURE-1 MenuInput Menu Multifunctional SettingsInput Menu Auto Menu Auto MenuScreen Menu Screen MenuOption Menu Wireless MenuOption Menu Related Messages Power Lamp Temp Regarding the Indicator LampsVol.2-7 Phenomena That May Easily Be Mistaken for Machine DefectsVol.2-2 Vol.2-3Unit mm SpecificationsDimension Diagram SpecificationWarranty and AFTER-SERVICE Sub 15-pin Shrink Signal Connector PIN AssignmentSignal Terminal Specification RGB in 1/2Resolution FH kHz FV Hz Rating Signal mode Display mode Example of Computer SignalInitial SET Signals PS/2 Mouse Connection to the Mouse ControlADB Mouse USB MouseProtocol Command dataConsist of header 7 bytes + command data 6 bytes RS-232C CommunicationRS-232C Communication C4 D3 Command data chartBe EF BA D2 Be EF AD D0 Be EF CB D0 Hitachi France Hitachi Europe GmbHHitachi Sales Europe GmbH Hitachi Business Systems NordicIN. P Picture in Picture US Type UK Type Europe Type Projector With Lens Cap Projector FeaturesPower cord Soft carrying case Remote controlDevices you will be using to the projector Only use the power cord that came with the projectorPart Names Remote Control Turn the elevator screw to fine tune Setting UP the ProjectorAdjusting the Projectors Elevator Feet Press and hold in the elevator ButtonsTop view Side view Adjusting the Screen Size and Projection DistanceScreen Connecting Your Devices Function Projector Port Connection Cables Ports and CablesConnecting to a Computer Connecting Your DevicesA a a BNC Input DVI InputConnecting to a Display Monitor Connecting to a DVD PlayerConnecting to a VCR Close the battery cover Using the Remote ControlPutting batteries into the remote control unit Remove the battery coverMeters with a 40-degree range Using the Remote ControlOperating the remote control Remote control in an area free from obstaclesTurning on the Power Selecting an Input Signal Turning on the PowerTurning OFF the Power Temporarily Muting the Sound Adjusting the VolumePress the Volume button Use the lever switch / to adjust the volumePress the Position button Adjusting the PositionUse the , , , buttons to adjust the position Press the Auto button Using the Automatic Adjustment FeatureAutomatic Adjustment for RGB Input Automatic Adjustment for Video InputOn the screen to aid you in correcting the distortion Correcting Keystone DistortionsPress the Keystone button As illustrated on the right, a dialog will appearFreezing the Screen Using the Magnify FeatureYou can activate the following functions just by Adjusting Screen with ONE-TOUCHWas begun When BNC RGB is selected Press the ONE Touch buttonPress the Blank button Selecting the Aspect RatioTemporarily Blanking the Screen Press the Aspect buttonPress the Menu button Using the Menu FunctionsUse the lever switch To adjust the level Operating the PC Screen Available Functions Remote Control OperationDo not use the projector with the lamp cover removed High Voltage High Temperature High PressureLamp Replacing the lamp LampCaring for the air filter AIR FilterReplacing the air filter AIR FilterCaring for the lens Caring for the cabinet and remote control transmitterOther Care Caring for the inside of the projector