Hitachi CP-X385W user manual Turning OFF the Power

Page 17

TURNING OFF THE POWER

STANDBY/ON BLANK

LASER

VIDEORGB

AUTO

MENUKEYSTONE

ENTER

POSITIONRESET

ASPECT FREEZE ESC

MAGNIFY MUTE

ON OFF

VOLUME

1	Press the STANDBY/ON button (control
	panel or remote control)

The message "Power off?" will appear on the screen for approximately 5 seconds.

STANDBY/ON

2	Press the STANDBY/ON button again
	(control panel or remote control)

Press the STANDBY/ON button again while the "Power off?" message is visible. The projector lamp goes off and starts cooling down. The POWER indicator blinks orange while the lamp cools down. (Pressing the STANDBY/ON button while the POWER indicator is blinking orange has no effect.)

The system goes into the STANDBY mode after cooling down and the POWER indicator stops blinking

STANDBY/ON

orange and then lights to solid orange.

Control panel	3	Check that the POWER indicator stops
		blinking and lights to solid orange.

Switch the power switch to [O] (OFF).

POWER-indikator

på/av-bryter

NOTE

•Except in emergencies, follow the above- mentioned procedure for turning power off.

4	Confirm that the POWER indicator has
	gone off and then attach the lens cap.

When the projector has completed powering down, the POWER indicator will go off.

16

Image 17

Contents Brukerhåndbok Vol.1 Grunnleggende Manuale Distruzioni Vol.1 Informazioni di baseContents Power cord Projector FeaturesCarrying Bag Remote Control US Type UK Type Europe Type Projector With Lens CapDevices you will be using to the projector Only use the power cord that came with the projectorUSB Port Handle Hook Power Switch AC Inlet To the Power CordPart Names Search button ButtonAngle Adjustment Setting UP the ProjectorTop View Side View Adjusting the Screen Size and Projection DistanceConnecting Your Devices Function Projector Port Connection Cables Ports and CablesConnecting to a Computer Connecting Your DevicesConnecting to a VCR Connecting to a DVD PlayerConnecting to a Display Monitor Operating the remote control Using the Remote ControlPutting batteries into the remote control unit Turning on the Power Selecting an Input Signal Turning OFF the Power Press the Volume button Adjusting the VolumePress Buttons to adjust Volume Temporarily Muting the SoundPress the Position button Adjusting the PositionUse Buttons to adjust Position Automatic Adjustment for RGB Input Using the Automatic Adjustment FeatureAutomatic Adjustment for Video Input Press the Auto buttonPress the Keystone button Correcting Keystone DistortionsAs illustrated on the right, a dialog will appear On the screen to aid you in correctingFreezing the Screen Using the Magnify FeatureTemporarily Blanking the Screen Signal SearchingSelecting the Aspect Ratio Select a menu using Buttons Then press Or Enter button Using the Menu FunctionsSelect an item using Buttons, then press Or Enter button Press Buttons to adjust the levelOperating the PC Screen Available Functions Remote Control OperationDo not use the projector with the lamp cover removed High Voltage High Temperature High PressureLamp Replacing the lamp LampCaring for the air filter AIR FilterReplacing the air filter Fixing the Handle HandleOther Care For Technical see the end of this manual Main Menu Multifunctional SettingsMain Menu Picture 2 Menu Picture 1 MenuPICTURE1 Menu PICTURE2 MenuInput Menu Input MenuAuto VideoScreen Menu Screen MenuBlank Start UPOption Menu VolumeOption Menu Auto OFFRelated Messages Power Lamp Temp Regarding the Indicator LampsVol.2-2 Phenomena That May Easily Be Mistaken for Machine DefectsVol.2-3 Vol.2-6Dimension Diagram SpecificationsSpecification Unit mmWarranty and AFTER-SERVICE Signal Terminal Specification Signal Connector PIN AssignmentRGB in 1/2 Sub 15-pin ShrinkResolution FH kHz FV Hz Rating Signal mode Display mode Example of Computer SignalInitial SET Signals ADB Mouse Connection to the Mouse ControlUSB Mouse PS/2 MouseConsist of header 7 bytes + command data 6 bytes Command dataRS-232C Communication ProtocolChanging the projector settings Set command Requesting projector status Get commandUsing the projector default settings Reset Command Increasing the projector setting value Increment command日本語 Command data chartBe EF BA D2 Be EF FD D3 Be EF Ntsc PAL Hitachi Sales Europe GmbH Hitachi Europe GmbHHitachi Business Systems Nordic Hitachi France