Hitachi CP-RX70 user manual Option Menu, Auto Search, Auto on, Auto OFF

Page 36

OPTION Menu

OPTION Menu

From the OPTION menu, items shown in the table below can be performed.

Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item, except for the items LAMP TIME and FILTER TIME. Then perform it according to the following table.

/'07=%1/276'4?

5'.'%6

2+%674'

#7615'#4%*674010

+/#)'

#76110674010

+0276

#7611((OKP

5'672

.#/26+/'J

5%4''0

(+.6'46+/'J

126+10

/;$76610

 

'#5;/'07

5'48+%'

 

 

5'%74+6;

 

Item

Description

Using the ▲/▼ buttons turns on/off the automatic signal search function.

TURN ON TURN OFF

 

When the TURN ON is selected, detecting no signal automatically cycles

 

through input ports in the following order. The search is started from the

AUTO SEARCH

current port. Then when an input is found, the projector will stop searching

 

and display the image.

 

 

COMPUTER IN1 COMPUTER IN2

 

 

VIDEO S-VIDEO

 

 

 

 

Using the ▲/▼ buttons turns on/off the AUTO ON function.

 

TURN ON TURN OFF

 

 

When set to the TURN ON, the lamp in projector will be automatically

 

turned on without the usual procedure (13), only when the projector is

AUTO ON

supplied with the power after the power was cut while the lamp was on.

 

• This function does not work as long as the power has been supplied to

 

the projector while the lamp is off.

 

 

• After turning the lamp on by the AUTO ON function, if neither input nor

 

operation is detected for about 30 minutes, the projector is turned off, even

 

though the AUTO OFF function (36) is disabled.

 

Using the ▲/▼ buttons adjusts the time to count down to

 

automatically turn the projector off.

 

 

Long (max. 99 minutes) ó Short (min. 0 minute = DISABLE)

 

AUTO OFF

AUTO OFF

 

ENABLE

DISABLE

 



0

AUTO OFF

When the time is set to 0, the projector is not turned off automatically.

When the time is set to 1 to 99, and when the passed time with no-

 

signal or an unsuitable signal reaches at the set time, the projector

 

lamp will be turned off.

 

 

If one of the projector's buttons or the remote control buttons

 

is pressed or one of the commands (except get commands) is

 

transmitted to the control port during the corresponding time,

 

projector will not be turned off.

 

 

Please refer to the section “Turning off the power” (13).

(continued on next page)

36

Image 36
Contents About this manual Thank you for purchasing this projectorTrademark acknowledgment Content Contents of package Fastening the lens coverReplacing the filter cover for bottom-up use Part names ProjectorHOT BottomRemote control Back Remote controlControl panel 3 4 5Setting up ArrangementOn a horizontal surface Suspended from the ceilingSetting up Connecting your devices VCR/DVD playerConnecting your devices About Plug-and-Play capabilityConnecting power supply Using the security slotSecurity slot Remote control Putting batteriesAbout the remote control signal Changing the frequency of remote control signalPower on/off Turning on the powerTurning off the power Adjusting the volume Selecting an input signal31, the volume adjustment is disable OperatingSearching an input signal Selecting an input signal For a PC signal  For no signalAdjusting the projectors elevator Adjusting the zoom and focusFocus ring Using the automatic adjustment feature Adjusting the positionUsing the magnify feature Correcting the keystone distortionsFreezing the screen Temporarily blanking the screenUsing the menu function Easy MenuAdvanced Menu Picture Mode DescriptionAspect KeystoneEasy Menu Picture Menu GammaUsing the / buttons switches the color temperature mode Selecting a mode whose name includesPicture Menu Custom and then pressing the button orMY Memory LOAD1, LOAD2, LOAD3, LOAD4SAVE1, SAVE2, SAVE3, SAVE4 Using the / buttons switches the mode for aspect ratio 43 ó 169 ó Small For no signalImage Menu Over ScanPhase Auto AdjustImage Menu SizeInput Menu ProgressiveVideo NR Color SpaceInput Menu Video FormatFrame Lock Resolution Setup Menu VolumeAudio Screen Menu BlankScreen Menu Start UPCapturing error has occurred. Please try again MyScreenMyScreen registration is finished Message Source NameOption Menu Auto SearchAuto on Auto OFFOption Menu Lamp TimeMY Button Service FAN Speed Select a color element of ghost using ButtonsGhost Disappear ghostService Filter MessageKEY Lock Remote FreqFactory Reset InformationIt shows the information about the current input Frame Lock message on the dialog means the frame lockUsing Security Features Inputting the PasswordChanging the Password SecurityUsing the MyScreen Password Function Description If you have forgotten your PasswordTurning on the MyScreen Password Setting the PasswordUsing the PIN Lock Function Turning the Password offSecurity Registering the PIN CodeTurning Off the PIN Lock Function If you have forgotten your PIN CodeMaintenance Case of replacement by yourselfLamp Type number DT00781 Replacing the lampLamp warning LampCleaning the air filter Air filterType number MU03602 Filter coverPage Troubleshooting There is no input signalInternal temperature is rising Related messagesRegarding the indicator lamps Resetting all settings Regarding the indicator lampsShutting the projector down Electrical power cord is not plugged Signal cables are not correctly connectedSignal source does not correctly work Input changeover settings are mismatchedColor settings are not correctly adjusted Color Space setting is not suitableNot properly adjusted Play monitorSpecifications SpecificationAir filter MU03602

CP-RX70 specifications

The Hitachi CP-RX70 is a versatile and powerful LCD projector designed for both educational and business environments. This model stands out with its compact size and lightweight design, making it highly portable while still offering reliable performance. With a resolution of 1024 x 768 pixels (XGA) and a brightness of 2700 ANSI lumens, the CP-RX70 ensures that presentations are clear, vibrant, and visible even in well-lit rooms.

One of the key features of the CP-RX70 is its advanced color technology. Hitachi utilizes a threeLCD system that enhances color reproduction, delivering rich and accurate colors for various content presentations. This makes it particularly suitable for displaying detailed images, charts, and videos, ensuring that every visual component is depicted with clarity and vibrancy.

The projector also boasts a contrast ratio of 600:1, providing deeper blacks and brighter whites that enhance the overall image quality. This level of contrast is essential for presentations that require nuanced visuals, making them more engaging and impactful for the audience.

In terms of connectivity, the Hitachi CP-RX70 offers multiple input options, including HDMI, VGA, and composite video, allowing users to easily connect various devices, such as laptops, DVD players, and document cameras. This flexibility in connectivity ensures that users can switch between devices with minimal hassle, enhancing the overall user experience during meetings or classes.

Hitachi has also integrated several convenient features to improve usability. The projector includes a built-in speaker, which adds to the overall functionality, negating the need for external audio for most presentations. Furthermore, the CP-RX70 comes with a remote control, providing users with a seamless way to operate the projector from a distance.

Another notable characteristic of this model is its energy-efficient design. The CP-RX70 has an eco mode that reduces power consumption and extends the life of the lamp, which can last up to 5,000 hours. This not only lowers operating costs but also contributes to environmental sustainability.

Overall, the Hitachi CP-RX70 is designed to meet the demands of modern presentations, combining portability, rich image quality, and user-friendly features to create a practical solution for educators and professionals alike.