NEC MT820, MT1020 user manual I N T E N a N C E, Replacing The Lamp, Step To replace the lamp

Page 32

4

M A I N T E N A N C E

61

 

 

 

 

 

This section describes the simple maintenance procedures you should follow to replace the lamp, clean or replace the filter, and replace the batteries in the remote control.

Replacing The Lamp

After your lamp has been operating for 2000 hours or longer, the “status” light in the cabinet will go on. Even though the lamp may still be working, replace it at 2000 hours to maintain optimal projector performance.

CAUTION

 

• DO NOT TOUCH THE LAMP immediately after it has been used. It will

 

be extremely hot. Allow at least one hour for the lamp to cool before

 

handling.

 

• DO NOT REMOVE ANY SCREWS except the lamp cover set screw

 

and two lamp case screws. You could receive an electric shock.

 

• Turn off the main power to the projector and disconnect the power cord.

 

Allow at least one hour for the lamp to cool.

 

• The projector will turn off and go into stand by mode after 2100 hours of

 

service. If this happens, be sure to replace the lamp. If you continue to

 

use the lamp after 2000 hours of use, the lamp bulb may shatter, and

 

pieces of glass may be scattered in the lamp case. Do not touch them as

 

the pieces of glass may cause injury. If this happens, contact your NEC

 

dealer for lamp replacement.

Interlock

Step 1A

Step 1B

Step 2

To replace the lamp:

1.Remove the single screw that secures the lamp housing cover and remove the cover.

2.Remove the two screws securing the lamp case. (There is an interlock on this case to prevent the risk of electrical shock. Do not attempt to circum- vent this interlock.)

3.Remove the lamp by pulling out the complete assembly.

4.Install a new lamp case assembly and secure it in place with the two screws.

CAUTION: Do not use a lamp other than the NEC replacement lamp. Order this from your NEC dealer using your projector's model number.

5.Reattach the lamp cover and reinstall the single screw.

6.After you install a new lamp, select the lamp Usage icon and press and hold the "Power On" button on the remote control for ten seconds to reset the lamp time clock to zero.

NOTE: If resetting the lamp clock back to zero after 2100 hours of service, press the "Power Off" (not "Power On") button on the remote control for ten seconds .

NOTE: When you replace the lamp, it is also wise to replace the filter. The filter comes in the same package with your replacement lamp.

CAUTION: Do not put the LCD projector on end except to replace the air filter.

Step 3

Step 4

Step 5

 

MAINTENANCE

 

62

 

 

 

 

Page 31 Page 33
Image 32
Page 31 Page 33
Contents MultiSync MT Tmtm Precautions P O R T a N T I N F O R M a T I O NInstallation Power SupplyCleaning Lamp ReplacementDOC avis de conformation Importantes précautions de sécuritéRemplacement de la lampe NettoyageAlimentation Précautions pour éviter un incendie ou une électrocutionNEC MultiSync LCD Projector Products M I T E D W a R R a N T YB L E O F C O N T E N T S IntroductionFeatures you’ll enjoy include T R O D U C T I O NHow Do You Get Started? What’s In The Box?Front Features Rear Features Right Side Features Left Side FeaturesTop Features Terminal Panel Features RGB Input 1 Connector D-Sub 15 pin RGB Input 2 Connector Mini D-Sub 15 pinRGB Monitor Output Connector Mini D-Sub 15 pin RGB 1 Audio Input Mini JackRemote Control Features Remote Control Precautions Installation Setting Up Your MultiSync MT1020/MT820 LCD ProjectorUsing a Tabletop Or Cart Rear Screen Projection Ceiling InstallationReflecting The Image Wiring Diagram Document CameraVCR or LaserDisk Player IBM VGA or Compatibles Macintosh or CompatiblesConnecting Your PC Or Macintosh Computer Windows MacintoshConnecting An External Monitor Connecting Your Document CameraConnecting Your VCR Or Laser Disc Player Connecting Your Remote Mouse Receiver Remote Mouse Receiver as a mouse for your computer E R a T I O N Using The Menus Video Menu Descriptions & FunctionsSource Menu Image Adjustment Menu VolumeImage Mode BrightnessPicture Adjustment when Auto Picture is off Fine Picture when Auto Picture is offHorizontal Position Vertical PositionPower Menu Power ManagementLamp Usage Auto StartSettings Menu ResetCustom Memory Image LoopI N T E N a N C E Replacing The LampStep To replace the lamp StepCleaning Or Replacing The Filter Remote Control Battery InstallationEtape 1A Etape 1B Pour remplacer la lampe EtapeNettoyage ou remplacement du filtre Installation des piles de la télécommandeCondition Status TroubleshootingStatus Light Messages Common Problems & Solutions Problem Check These ItemsSpecification S OpticalElectrical MechanicalCabinet Dimensions Sub Pin Assignments PC 15-Pin mini D-Sub Macintosh 15-Pin D-SubTiming Chart PC Control Command Reference Command Codes Function Code Data Description1DH Cable Connection Communication Protocol To RxD of PC

MT1020, MT820 specifications

The NEC MT820 and MT1020 are high-performance projectors designed to meet the needs of various presentation environments. Renowned for their reliability and image quality, these projectors are ideal for educational institutions, corporate settings, and public venues.

One of the standout features of both models is their impressive brightness. The MT820 boasts a brightness of up to 2700 ANSI lumens, while the MT1020 offers an even higher brightness level of 3000 ANSI lumens. This makes them suitable for use in well-lit rooms where clear visibility is critical. The high brightness levels ensure that images and presentations remain vibrant and easy to read, even in challenging lighting conditions.

In terms of resolution, the MT820 and MT1020 support XGA (1024x768) native resolution, allowing for detailed and sharp visuals. Additionally, both projectors can handle various input sources, including VGA, HDMI, and composite video, providing excellent versatility for connecting to different devices such as laptops, DVD players, and multimedia players.

The NEC MT820 and MT1020 utilize DLP (Digital Light Processing) technology, which enhances their performance by providing better color accuracy and improved longevity when compared to other projection technologies. This means that users can expect high-quality images that remain consistent over time without the risk of color degradation.

Portability is another key characteristic of these projectors. Weighing in at around 4.5 kg (approximately 10 lbs), the MT820 and MT1020 are designed for ease of transport, making them suitable for on-the-go presentations. Their compact size facilitates quick setup and dismantle, making them ideal candidates for traveling professionals and educators who need to move from one location to another.

For ease of use, both models come equipped with a user-friendly interface, making system navigation intuitive for first-time users as well as seasoned professionals. The projectors also feature built-in speakers, providing decent audio output without the need for external sound systems, which is a great advantage in smaller presentation settings.

In summary, the NEC MT820 and MT1020 projectors stand out due to their excellent brightness levels, reliable DLP technology, versatile input options, portability, and user-friendly features. These characteristics make them suitable for diverse presentation environments, ensuring that audiences receive clear, high-quality visuals regardless of the setting. Whether used in a classroom or a business meeting, these projectors provide a reliable solution for all projection needs.
Top Page Image Contents