NEC VT460K, VT660K, VT560 manual Projecting AN Image Basic Operation, Turning on the Projector

Page 17

PROJECTING AN IMAGE (BASIC OPERATION)

This section describes how to turn on the projector and to project a 2. Press the ENTER button to execute the selection. picture onto the screen.

Turning on the Projector

NOTE:

•The projector has two power switches: main power switch and POWER (ON/ STAND BY) button (POWER ON and OFF on the remote control).

•When plugging in or unplugging the supplied power cable, make sure that the main power switch is pushed to the off (O) position. Failure to do so may cause damage to the projector.

To turn on the main power to the projector, press the Main Power switch to the on position ( I ).

Before you turn on your projector, ensure that the computer or video source is turned on and that your lens cap is removed.

Only after you press the POWER (ON/STAND BY) button on the pro- jector cabinet or POWER ON button on the remote control for a mini- mum of 2 seconds will the power indicator turn to green and the projec- tor become ready to use.

After this has been done, you can proceed to the menu operation.

If you want, you can select the menu language later. See "Language" on page E-27.

NOTE: Immediately after turning on the projector, screen flicker may occur. This is not a fault. Wait 3 to 5 minutes until the lamp lighting is stabilized.

When the Lamp mode is set to Eco, the Lamp indicator will light green. If one of the following things happens, the projector will not turn on.

*If the internal temperature of the projector is too high, the projector detects abnormal high temperature. In this condition the projector will not turn on to protect the internal system. If this happens, wait for the projector's internal components to cool down.

*When the lamp reaches its end of usable life, the projector will not turn on. If this happens, replace the lamp.

*If the lamp fails to light, and if the STATUS indicator flashes on and off in a cycle of six times, wait a full minute and then turn on the power.

Note on Startup screen (Menu Language Select screen)

When you first turn on the projector, you will get the Startup screen. This screen gives you the opportunity to select one of the 21 menu languages. To select a menu language, follow these steps:

1.Use the SELECT G or H button to select one of the 21 languages for the menu.

E-17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents VT660K/VT460K VT560 Safety Cautions Whats in the Box? Fire and Shock PrecautionsLamp Replacement Table of Contents Introduction to the Projector Features youll enjoyIntroduction Attaching the supplied carrying handle Part Names of the ProjectorTop Features Terminal Panel Features Part Names of the Remote Control Remote Control Precautions Battery InstallationSelecting a Location Installation and ConnectionsSetting Up the Screen and the Projector Do not attempt to install the projector yourself Distance ChartThrow Distance and Screen Size Reflecting the ImageMaking Connections Connecting Your PC or Macintosh ComputerTo connect Scart output RGB Connecting an External MonitorRGB Connecting Your DVD PlayerConnecting the Supplied Power Cable Connecting Your VCR or Laser Disc PlayerTurning on the Projector Projecting AN Image Basic OperationAdjust the Tilt Foot Adjusting the Picture Size and PositionSelecting a Source Selecting the computer or video sourceAuto Keystone Correction Correcting the Vertical Keystone DistortionManual Keystone Correction FocusTo turn off the projector Turning Up or Down VolumeAdjusting the Image Using Auto Adjust Using the Remote Mouse Function Convenient FeaturesFreezing a Picture Turning off the Image and SoundEnlarging and Moving a Picture Getting the InformationBasic Menu Operation Using ON-SCREEN MenuUsing the Menus List of Menu Items Menu Elements Indicates the Control Panel Key Lock is enabledImage Menu Descriptions & FunctionsPicture Advanced SetupEnabling High Speed Fan Mode High Speed Fan Mode To disable the Security functionSelecting Signal Format Signal Select Page2 Enabling Power Management Power ManagementInformation DefaultTo replace the lamp MaintenanceReplacing the Lamp Cleaning or Replacing the Filter CleaningCleaning the Cabinet and the Lens To replace the filter spongePower Indicator TroubleshootingStatus Indicator Lamp IndicatorDoes not turn on Common Problems & Solutions Check These ItemsModel Number VT660K/VT460K/VT560 Optical SpecificationsPin Assignments of D-Sub RGB Input Connector Cabinet DimensionsMini D-Sub 15 Pin Connector Pin No RGB Signal Analog YCbCr SignalSXGA+ Compatible Input Signal ListCable Connection Communication Protocol PC Control CodesServices offered with TravelCare TravelCare a service for international travelersTerm of warranty TravelCare GuideAsia and Middle East Service are offeredApplication Sheet for TravelCare Service Program Condition of your TravelCare Service Program

VT460K, VT560, VT660K specifications

The NEC VT460K, VT560, and VT660K are part of a renowned line of projectors that stand out for their reliability, performance, and versatility, designed primarily for educational and business environments. Each model offers unique features tailored to meet the diverse needs of users while maintaining high standards of image quality and ease of use.

Starting with the NEC VT460K, this model is characterized by its exceptional portability and lightweight design, making it an ideal choice for on-the-go presentations. It boasts a brightness of 5000 lumens and a native resolution of XGA (1024x768), ensuring clear and vibrant images even in brightly lit rooms. Its lamp life is impressive, with Eco mode extending usage to a remarkable 10,000 hours, minimizing maintenance costs. The VT460K also features a variety of connectivity options, including HDMI and VGA ports, allowing for seamless integration with various devices.

The VT560 offers a step up in terms of resolution and brightness. With a native resolution of WXGA (1280x800) and 5500 lumens of brightness, it is designed for slightly larger venues where image clarity is paramount. The addition of advanced image processing technologies enhances color accuracy and contrast, providing an immersive viewing experience. The VT560 also emphasizes user-friendly features, such as a straightforward menu system and an intuitive remote control, making it accessible for all users, regardless of technical expertise.

Lastly, the VT660K takes performance to the next level with full HD resolution of 1920x1080 and an output of 6000 lumens. This model is particularly suited for high-definition content and large-screen applications, making it ideal for conferences and seminars. The VT660K is equipped with advanced lens shift and zoom capabilities, providing flexibility in installation and setup. Furthermore, it incorporates enhanced networking features, allowing for wireless presentations and remote management, catering to modern business needs.

All three models prioritize energy efficiency and environmental sustainability, with features like eco-friendly modes and low energy consumption. Their robust build quality ensures longevity and consistent performance, confirming NEC’s commitment to producing reliable projection solutions. Whether for classrooms, meeting rooms, or larger auditoriums, the VT460K, VT560, and VT660K deliver outstanding performance and versatility tailored to various presentation needs.
Top Page Image Contents