NEC VT660K, VT560, VT460K manual Maintenance, Replacing the Lamp, To replace the lamp

Page 30

MAINTENANCE

This section describes the simple maintenance procedures you should

3. Insert a new lamp housing until the lamp housing is plugged into the

follow to replace the lamp and clean the filter.

socket.

Replacing the Lamp

After your lamp has been operating for 2000 hours (up to 3000 hours in Eco mode) or longer, the LAMP indicator in the cabinet will blink red and the message will appear. Even though the lamp may still be work- ing, replace it at 2000 (up to 3000 hours in Eco mode) hours to maintain optimal projector performance.

CAUTION

•DO NOT TOUCH THE LAMP immediately after it has been used. It will be extremely hot. Turn the projector off, wait 60 seconds, turn off the main power switch and then disconnect the power cable. Allow at least one hour for the lamp to cool before han- dling.

•DO NOT REMOVE ANY SCREWS except the lamp cover screw and two lamp case screws. You could receive an electric shock.

•The projector will turn off and go into stand by mode after 2100 (up to 3100 hours in Eco mode) hours of service. If this hap- pens, be sure to replace the lamp. If you continue to use the lamp after 2000 hours (up to 3000 hours in Eco mode) of use, the lamp bulb may shatter, and pieces of glass may be scat- tered in the lamp case. Do not touch them as the pieces of glass may cause injury. If this happens, contact your NEC dealer for lamp replacement.

CAUTION

Do not use a lamp other than the NEC replacement lamp (VT60LP). Order this from your NEC dealer.

Secure it in place with the two screws.

Be sure to tighten the screws.

4.Reattach the lamp cover.

Tighten the lamp cover screw. Be sure to tighten the screw.

To replace the lamp:

1.Loosen the lamp cover screw until the screwdriver goes into a free- wheeling condition and remove the lamp cover. The lamp cover screw is not removable.

Catch

2.Loosen the two screws securing the lamp housing until the screw- driver goes into a freewheeling condition. The two screws are not removable.

Remove the lamp housing by holding it.

NOTE: There is an interlock on this case to prevent the risk of electrical shock. Do not attempt to circumvent this interlock.

Catch

Interlock

5.After you install a new lamp, select the menu → [Default] → [Clear Lamp Hour Meter] to reset the lamp usage hours.

NOTE: When the lamp exceeds 2100 hours (up to 3100 hours in Eco mode) of service, the projector cannot turn on and the menu is not displayed. If this happens, press the Help button on the remote control for a minimum of 10 seconds while in standby mode. When the lamp time clock is reset to zero, the LAMP indicator goes out.

E-30

Page 29 Page 31
Image 30
Page 29 Page 31
Contents VT660K/VT460K VT560 Safety Cautions Fire and Shock Precautions Lamp ReplacementWhats in the Box? Table of Contents Features youll enjoy IntroductionIntroduction to the Projector Part Names of the Projector Attaching the supplied carrying handleTop Features Terminal Panel Features Part Names of the Remote Control Battery Installation Remote Control PrecautionsInstallation and Connections Setting Up the Screen and the ProjectorSelecting a Location Throw Distance and Screen Size Distance ChartDo not attempt to install the projector yourself Reflecting the ImageConnecting Your PC or Macintosh Computer Making ConnectionsConnecting an External Monitor To connect Scart output RGBConnecting Your DVD Player RGBConnecting Your VCR or Laser Disc Player Connecting the Supplied Power CableProjecting AN Image Basic Operation Turning on the ProjectorSelecting a Source Adjusting the Picture Size and PositionAdjust the Tilt Foot Selecting the computer or video sourceManual Keystone Correction Correcting the Vertical Keystone DistortionAuto Keystone Correction FocusTurning Up or Down Volume Adjusting the Image Using Auto AdjustTo turn off the projector Convenient Features Using the Remote Mouse FunctionEnlarging and Moving a Picture Turning off the Image and SoundFreezing a Picture Getting the InformationUsing ON-SCREEN Menu Using the MenusBasic Menu Operation List of Menu Items Indicates the Control Panel Key Lock is enabled Menu ElementsMenu Descriptions & Functions PictureImage Setup AdvancedSelecting Signal Format Signal Select To disable the Security functionEnabling High Speed Fan Mode High Speed Fan Mode Page2 Enabling Power Management Power ManagementDefault InformationMaintenance Replacing the LampTo replace the lamp Cleaning the Cabinet and the Lens CleaningCleaning or Replacing the Filter To replace the filter spongeStatus Indicator TroubleshootingPower Indicator Lamp IndicatorCommon Problems & Solutions Check These Items Does not turn onSpecifications Model Number VT660K/VT460K/VT560 OpticalMini D-Sub 15 Pin Connector Cabinet DimensionsPin Assignments of D-Sub RGB Input Connector Pin No RGB Signal Analog YCbCr SignalCompatible Input Signal List SXGA+PC Control Codes Cable Connection Communication ProtocolTerm of warranty TravelCare a service for international travelersServices offered with TravelCare TravelCare GuideService are offered Asia and Middle EastApplication Sheet for TravelCare Service Program Condition of your TravelCare Service Program

VT460K, VT560, VT660K specifications

The NEC VT460K, VT560, and VT660K are part of a renowned line of projectors that stand out for their reliability, performance, and versatility, designed primarily for educational and business environments. Each model offers unique features tailored to meet the diverse needs of users while maintaining high standards of image quality and ease of use.

Starting with the NEC VT460K, this model is characterized by its exceptional portability and lightweight design, making it an ideal choice for on-the-go presentations. It boasts a brightness of 5000 lumens and a native resolution of XGA (1024x768), ensuring clear and vibrant images even in brightly lit rooms. Its lamp life is impressive, with Eco mode extending usage to a remarkable 10,000 hours, minimizing maintenance costs. The VT460K also features a variety of connectivity options, including HDMI and VGA ports, allowing for seamless integration with various devices.

The VT560 offers a step up in terms of resolution and brightness. With a native resolution of WXGA (1280x800) and 5500 lumens of brightness, it is designed for slightly larger venues where image clarity is paramount. The addition of advanced image processing technologies enhances color accuracy and contrast, providing an immersive viewing experience. The VT560 also emphasizes user-friendly features, such as a straightforward menu system and an intuitive remote control, making it accessible for all users, regardless of technical expertise.

Lastly, the VT660K takes performance to the next level with full HD resolution of 1920x1080 and an output of 6000 lumens. This model is particularly suited for high-definition content and large-screen applications, making it ideal for conferences and seminars. The VT660K is equipped with advanced lens shift and zoom capabilities, providing flexibility in installation and setup. Furthermore, it incorporates enhanced networking features, allowing for wireless presentations and remote management, catering to modern business needs.

All three models prioritize energy efficiency and environmental sustainability, with features like eco-friendly modes and low energy consumption. Their robust build quality ensures longevity and consistent performance, confirming NEC’s commitment to producing reliable projection solutions. Whether for classrooms, meeting rooms, or larger auditoriums, the VT460K, VT560, and VT660K deliver outstanding performance and versatility tailored to various presentation needs.
Top Page Image Contents