NEC IB-USB, A3844 user manual Troubleshooting, Usb

Page 22

NEC204 Eng.Fr.manual 10/26/98 10:21 AM Page 22

Troubleshooting

SYMPTOMS

POSSIBLE PROBLEM

SOLUTION

 

 

 

 

NOTE

 

 

 

 

 

 

 

USB devices

No power to unit.

Make sure all connecting plugs

The green

power indicator

plugged

 

 

 

 

 

between

the IntelliBase

and

on the IntelliBase will light

into the

 

 

 

 

 

computer

are

fully

seated.

when power is applied.

 

IntelliBase

 

 

 

 

 

Make sure the wall power outlet

 

 

 

do not

 

 

 

 

 

or power strip has power.

 

 

 

work.

 

 

 

 

 

Make sure the power switch on

 

 

 

 

 

 

 

 

 

the power strip is turned on.

 

 

 

 

 

 

 

 

 

 

 

USB

cable

is

not

Make sure both ends of

The green USB indicator will

 

properly connected.

the USB cable are fully

light when the USB line is

 

 

 

 

 

 

seated in the computer and

active.

 

 

 

 

 

 

 

 

IntelliBase.

 

 

 

 

 

 

 

 

 

 

 

USB device is plugged

USB devices connected to

Do not plug a USB device

 

into the

wrong

USB

the

IntelliBase must

be

into the rear of the

 

port.

 

 

 

 

plugged

into

the

output

IntelliBase.

This USB

port

 

 

 

 

 

 

ports.

These

ports

are

must be used to connect the

 

 

 

 

 

 

found on the right side of

host computer.

 

 

 

 

 

 

 

the IntelliBase.

 

 

 

 

 

 

 

There is a problem with

Verify that USB devices will

For this check, disconnect the

 

the host

computer or

work

 

when

connected

IntelliBase from the computer

 

software.

 

 

 

directly

 

to

the

 

host

and plug the USB devise

 

 

 

 

 

 

computer.

 

 

 

 

(mouse,

keybord,

etc.)

 

 

 

 

 

 

 

 

 

 

 

 

 

directly into the computer.

 

 

 

 

 

 

 

 

 

 

There

is

a

problem

Using the same USB output

 

 

 

 

with the specific USB

port,

try

substituting a

 

 

 

 

device.

 

 

 

different USB device.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NOTE: If the IntelliBasemust be returned for repair, the unit must be disconnected from the monitor and packed in its original packaging.

18

Image 22
Contents MultiSync IntelliBase USB Hub Index Table des matièresSafety Precautions and Maintenance Connecting the Power Cord FCC Wants You to KnowContents Quick Start MultiSync Monitor Model Names Original Monitor BaseMultiSync Monitor Model Names Locate Adapter Plate a that Is supplied with Base Locking Tabs Using a Phillips Locate the two Screws that Are supplied With Original Mounting NEC204 Eng.Fr.manual 10/26/98 1020 AM Adapter plate Detail a NEC204 Eng.Fr.manual 10/26/98 1020 AM NEC204 Eng.Fr.manual 10/26/98 1020 AM NEC204 Eng.Fr.manual 10/26/98 1020 AM NEC204 Eng.Fr.manual 10/26/98 1020 AM Controls Specifications System Hardware RequirementsTroubleshooting USB978 ReferencesFastFacts Information 800 Limited Warranty Consignes de sécurité et entretien Raccordement du cordon Prise murale c.aContenu VisDémarrage rapide Noms des modèles de moniteurs MultiSync La FigureLa plaque Étape 3 RepérerLa B AdaptatriceBase Pattes Blocage La C La E MultiSync XE21, XP21, E1100, E1100+, P1150 et P1250+Montage D’ORIGINE NEC204 Eng.Fr.manual 10/26/98 1021 AM ’IntelliBasemc Étape 8 Repérer les deux Vis qui sontFournies avec Et fixerVUE Arrière NEC204 Eng.Fr.manual 10/26/98 1022 AM NEC204 Eng.Fr.manual 10/26/98 1022 AM NEC204 Eng.Fr.manual 10/26/98 1022 AM NEC204 Eng.Fr.manual 10/26/98 1022 AM Commandes Caractéristiques Dépannage RemarqueRéférences Déclaration du fabricantGarantie limitée Avis DE Propriété Exclusive ET Dénégation DE Responsabilité Proprietary Notice and Liability Disclaimer