Epson DR-EPS19 quick start Relays, Other Presets

Page 4

SmartPanel Projector Driver Application Note

Epson EMP-7800

Hidden functions are accessed by pressing the indicated key while the holding the On key down.

Hidden functions names are based on the Epson remote and controls on top of the projector. Adjust, Enter and ESC controls navigate through onscreen menus. A/V Mute is a toggling Audio and Video mute.

The hidden functions available for the Epson with this Driver are as follows:

MENU

BRIGHT +

TRACKING +

ADJUST LEFT

BRIGHT –

TRACKING –

ADJUST RIGHT

E-ZOOM +

A/V MUTE

ADJUST UP

E-ZOOM

HELP

ADJUST DOWN

SYNC +

RESIZE

ENTER

SYNC –

 

ESC

 

 

D. Relays

 

 

 

 

 

RELAYS

500mA MAX. CURRENT

 

PWR

PWR

PWR

 

SELECTION

 

ON

ON

OFF

(EXT. SWITCHER CTRL)

 

MAINT.

MOM.

MOM.

4

3

2

1

The following table specifies the factory preset settings for the low-current relays found on the rear of the SmartPanel. The Configuration Utility can be used to customize these settings your installation.

 

 

1A

1B

 

2A

2B

 

3A

3B

 

 

4A

4B

 

5A

5B

 

6A

6B

 

7A

7B

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Relay 1

ON Maintained

Relay 2

ON Momentary

Relay 3

OFF Momentary

Selection

Momentary; not Binary

E. Other Presets

The following table specifies other default factory settings for this Driver that affect is control of the Projector.

Power Status Feedback Method

RS-232

Polling (see note 1)

Control Wiring Option

RS-232

Only (see note 2)

All control for the Epson with this Driver is via RS-232. However, SP Controls strongly recommends wiring the IR emitter. See Section III. Projector Firmware Note below for more information.

The following table specifies settings for the Panel’s configurable timers. For more information on the inactivity shutdown feature and the lockout timer see the SmartPanel Configuration and Installation Manual.

Lockout Timer

42 seconds (see note 3)

Inactivity Shutdown

Disabled

© 2004 SP Controls Inc. 601 Minnesota Suite 115, San Francisco, CA 94107

help@spcontrols.com

Image 4
Contents II. Wiring Specifications Driver FeaturesQuick Start Reference Sheet SmartPanel Projector Driver Application Note III. Additional Projector InformationHelp@spcontrols.com Volume and Power Control Projector Driver Application NoteProjector Control Hidden Function MappingOther Presets RelaysII. Control Wiring Control RS-232CIII. Projector Firmware Note IV. Troubleshooting Technical NotesVI. Revision History Projector is not responding to Panel control