NEC LCD4215 Setup, Determine the installation location, Install the remote control batteries

Page 13

Setup

English

1. Determine the installation location

CAUTION: Installing your LCD display must be done by a qualified technician. Contact your dealer for more information.

CAUTION: MOVING OR INSTALLING THE LCD MONITOR MUST BE DONE BY TWO OR MORE PEOPLE. Failure to follow this caution may result in injury if the LCD monitor falls.

CAUTION: Do not mount or operate the display upside down, face up, or face down.

CAUTION: This LCD has a temperature sensor and cooling fan. If the LCD becomes too hot, the cooling fan will turn on automatically. If the LCD becomes overheated while the cooling fan is running, a ÒCautionÓ warning will appear. If the ÒCautionÓ warning appears, discontinue use and allow the unit to cool. Using the cooling fan will reduce the likelihood of early circuit failure and may help reduce image degradation and ÒImage PersistanceÓ.

If the LCD is used in an enclosed area or if the LCD panel is covered with a protective screen, please check the inside temperature of the monitor by using the ÒHEAT STATUSÓ control in the OSD (see page 23). If the temperature is higher than the normal operating temperature, please turn the cooling fan to ON within the SCREEN SAVER menu within the OSD (see page 23).

IMPORTANT: Lay the protective sheet, which was wrapped around the LCD monitor when it was packaged, beneath the LCD monitor so as not to scratch the panel.

2. Install the remote control batteries

The remote control is powered by two 1.5V AAA batteries. To install or replace batteries:

A.Press and slide to open the cover.

B.Align the batteries according to the (+) and (Ð) indications inside the case.

C.Replace the cover.

CAUTION: Incorrect usage of batteries can result in leaks or bursting.

NEC recommends the following battery use:

¥Place ÒAAAÓ size batteries matching the (+) and (-) signs on each battery to the (+) and (-) signs of the battery compartment.

¥Do not mix battery brands.

¥Do not combine new and old batteries. This can shorten battery life or cause liquid leakage of batteries.

¥Remove dead batteries immediately to prevent battery acid from leaking into the battery compartment.

¥Do not touch exposed battery acid, it may injure skin.

NOTE: If you do not intend to use the Remote Control for a long period of time, remove the batteries.

3. Connect external equipment (See pages 13-17)

¥To protect the external equipment; turn off the main power before making connections.

¥Refer to your equipment user manual for further information.

4. Connect the supplied power cord

¥The equipment should be installed close to an easily accessible power outlet.

¥Fully insert the prongs into the power outlet socket. A loose connection may cause image degradation.

NOTE: Please refer to the ÒSafety Precautions and MaintenanceÓ section of this manual for proper selection of AC power cord.

English-11

Image 13
Contents MultiSync LCD3215 MultiSync LCD4215 Advanced Option IndexRegistration Information Important InformationDeclaration Declaration of the ManufacturerFCC Information Canadian Department of Communications Compliance StatementDeclaration of Conformity English-2Safety Precautions, Maintenance & Recommended Use Contents Installation Attach Mounting Accessories Attaching Mounting AccessoriesInstalling and removing optional table top stand Ventilation RequirementsControl Panel Parts Name and FunctionsTerminal Panel Wireless Remote Control Handling the remote control Operating Range for the Remote ControlEnglish-10 Determine the installation location SetupInstall the remote control batteries Connect the supplied power cordAdjust the sound Switch on the power of all the attached external equipmentAdjust the screen See pages 21 Adjust the image SeeConnections Wiring DiagramBefore making connections English-13Connect the LCD Monitor to a Personal Computer Connecting a Personal ComputerEnglish-14 Connect the LCD Monitor to a Computer with a Digital Output Connecting with Digital Interface EquipmentEnglish-15 Connect the LCD Monitor to a DVD Player Connecting a DVD Player with component outEnglish-16 DVI-D BNCConnect the LCD Monitor to a Stereo Amplifier Connecting to a Stereo AmplifierEnglish-17 RCABasic Operation Power on and OFF ModesEnglish-18 Using Power Management Power IndicatorPicture Mode Information OSD Selecting a video sourceEnglish-20 OSD On-Screen-Display ControlsEnglish-21 English-22 English-23 English-24 Recommendations Image Sticking of LCD PanelEnglish-25 English-26 ConnectionEnglish-27 FeaturesTroubleshooting Product Specifications Specifications LCD3215English-29 English-30 Specifications LCD4215English-31 Pin AssignmentDisposing of your old NEC product Manufacturer’s Recycling and Energy InformationEnergy Saving Weee Mark European Directive 2002/96/EC
Related manuals
Manual 2 pages 7.75 Kb