NEC PA271W Remove Monitor Stand for Mounting, Flexible Arm Installation, Figure S.1, Figure F.1

Page 10
Remove Monitor Stand for Mounting

Remove Monitor Stand for Mounting

To prepare the monitor for alternate mounting purposes:

1. Disconnect all cables.

2. Place hands on each side of the monitor and lift up to the highest position.

3.Place monitor face down on a non-abrasive surface (Figure S.1).

4.Place one hand around the base and one hand on the Quick Release Lever.

Push and hold the Quick Release Lever in the direction indicated by the arrows (Figure S.1).

5. Lift up the stand to unhook it from the monitor (Figure S.1). The monitor can now be mounted using an alternate method. Reverse process to reattach stand.

NOTE: Handle with care when removing monitor stand.

Figure S.1

Flexible Arm Installation

This LCD monitor is designed for use with a fl exible arm.

1.Follow the instructions on how Remove Monitor Stand for Mounting to remove the stand.

2.Using the 4 screws from the stand removal and attach the arm to the monitor (Figure F.1).

Caution: Use ONLY the screws (4 pcs) that are included or the screws M4 size (Length: bracket thickness + 10-12 mm) when mounting to avoid damage to the monitor and stand. To fulfi l the safety requirements the monitor must be mounted to an arm which guaranties the necessary stability under consideration of the weight of the monitor. The LCD monitor should only be used with an approved arm (e.g. GS mark).

200 mm*2

100 mm

Unit

 

Mounting

 

 

 

Bracket

 

 

 

Washer

 

 

 

Screw

 

 

10-12 mm

Thickness

 

 

 

 

 

 

of bracket

100 mm

 

 

and washer

NOTE: Tighten all screws.

Weight of LCD assembly: 7.4 kg (PA241W)

9.6 kg (PA271W)

(recommended Fasten Force: 98 - 137N•cm)

Figure F.1

 

*2 Only for PA271W.

 

English-8

Page 9 Page 11
Image 10
Page 9 Page 11
Contents
MultiSync PA241W MultiSync PA271W User’s ManualIndex Declaration of the Manufacturer DeclarationEnglish FCC Information Canadian Department of Communications Compliance StatementDeclaration of Conformity We hereby declare that the equipment specified above conformsContents Product FeaturesEnglish-3 Figure A.4 Quick Start Figure A.3 Figure A.1Figure C.2 Figure C.1aFigure C.1 Figure C.3Figure E.1 Raise and Lower Monitor ScreenFigure D.1 Figure RL.1Swivel Screen RotationTilt Figure R.1Figure S.1 Flexible Arm InstallationRemove Monitor Stand for Mounting Figure F.1SETTING OSD LANGUAGE ControlsBrightness/Contrast Controls Auto Adjust Analog input only*1AUTO ADJUST Image ControlsColor Control Systems ADJUSTADVANCED SETTING FINE Analog input only*1PIP MODE OFF TIMERTools PIP INPUTOFF MODE RESOLUTION NOTIFIERMENU Tools LANGUAGEInformation FACTORY PRESETECO Information OSD WarningPRESET Using the PICTURE MODE functionThe type of PRESET PURPOSEAdvanced OSD English-17 English-18 English-19 AnalogEnglish-20 English-21 English-22 English-23 Safety Precautions and Maintenance Recommended useEnglish-24 Ergonomics Cleaning the LCD PanelCleaning the Cabinet English-25MultiSync PA241W Specifications - PA241WMonitor Specifications English-26Specifications - PA271W Quick Release stand Allows fast removal FeaturesEnglish-28 English-29 Troubleshooting LED on monitor is not lit no green, blue or amber color can be seenUSB Hub does not operate No VideoSelf Diagnosis English-31Using the Auto Brightness function SETUPErgonomics CongratulationsTCO’03 for MultiSync PA271W EnergyTCO Displays 5.0 for MultiSync PA241W Some of the Usability features of the TCO Certified for displaysSome of the Environmental features of the TCO Certified for displays This display is designed for both you and the planetEnergy Saving Manufacturer’s Recycling and Energy InformationDisposing of your old NEC product WEEE Mark European Directive 2002/96/EC
Related manuals
Manual 36 pages 652 b
Top Page Image Contents