NEC V462, V651 user manual Display Protection, English-25

LAN SETTING		When you use this function, EXTERNAL CONTROL should be “LAN”.
		NOTE: When changing the LAN SETTING, turn the monitor off and then back on.
		After turning on the monitor, you need to wait several seconds until the LAN SETTING is applied.
	DHCP	Enabling this option automatically assigns an IP address to the monitor from your DHCP server.	DISABLE
		Disabling this option allows you to register the IP address or subnet mask number obtained from
		your network administrator.
		NOTE: Consult your network administrator for the IP address when “ENABLE” is selected for
		[DHCP].
	IP ADDRESS	Set your IP address of the network connected to the monitor when “DISABLE” is selected for	192.168.0.10
		[DHCP].
	SUBNET MASK	Set your subnet mask number of the network connected to the monitor when “DISABLE” is	255.255.255.0
		selected for [DHCP].
	DEFAULT GATEWAY	Set your default gateway of the network connected to the monitor when “DISABLE” is selected	192.168.0.1
		for [DHCP].
	DNS PRIMARY	Set your primary DNS settings of the network connected to the monitor.	0.0.0.0
	DNS SECONDARY	Set your secondary DNS settings of the network connected to the monitor.	0.0.0.0
SETTING COPY		In a daisy chain scenario, select the OSD menu categories that you want to copy over to the	NO
		other monitor.
		NOTE: When you use this function, EXTERNAL CONTROL should be “RS-232C”.
		This function resets to default when power is off. This function has a limit depending on the cable
		you use.
	COPY START	Select “YES” and press the SET button to start copying.
	ALL INPUT	All input terminals settings are copied when you select this item. Default is off.
RESET		Resets “MULTI DISPLAY” options back to factory settings except LAN SETTING.	-
DISPLAY PROTECTION
POWER SAVE		Sets how long the monitor waits to go into power save mode after the signal is lost.	ON
		Note: When connecting DVI, the video card might not stop sending the digital data even
		though the image might have disappeared. If this occurs the monitor will not switch into power
		management mode.
HEAT STATUS		Displays status of the FAN, BACKLIGHT and TEMPERATURE.	-
FAN CONTROL		Cooling fan reduces the temperature of the display to protect from overheating.	AUTO
		If “AUTO” is selected, you can adjust the start temperature of the cooling fan and fan speed.
SCREEN SAVER		Use the SCREEN SAVER function to reduce the risk of Image Persistence.
	GAMMA	The display gamma is changed and fi xed when “ON” is selected.	OFF
	BACKLIGHT	The brightness of backlight is decreased when “ON” is selected.	OFF
	MOTION	The screen image is slightly expanded and moves in 4 directions (UP, DOWN, RIGHT, LEFT) at	OFF
		user determined intervals. You can set interval time and zooming ratio.
		This function is disabled when PIP, STILL, TEXT TICKER or TILE MATRIX are enabled.
SIDE BORDER COLOR		Adjusts the color of the side borders when a 4:3 image is displayed.	15
		Press + button, the bar will become lighter.
		Press - button, the bar will become darker.
AUTO BRIGHTNESS		Adjusts the brightness level according to the input signal.	OFF
DPORT, DVI, VGA, RGB/HV inputs only
CHANGE SECURITY		Allows the security password to be changed.	-
PASSWORD		The factory preset password is 0000.
SECURITY		Locks the security password.	OFF
DDC/CI		ENABLE/DISABLE: Turns ON or OFF the two way communication and control of the monitor.	ENABLE
ALERT MAIL		Selects whether or not to send an e-mail notifi cation of monitor error via wired LAN.	OFF
RESET		Resets the following settings within the DISPLAY PROTECTION menu back to factory	-
		setting: POWER SAVE, FAN CONTROL, SCREEN SAVER, SIDE BORDER COLOR,
		AUTO BRIGHTNESS, DDC/CI.

English

English-25