NEC JC-1946UMW, JC-2241UMW Color Control/AccuColor Control System, Geometry Controls, Tools

Page 9

Controls cont.

Color Control/AccuColor® Control System

Color presets 1 through 5 selects the desired color setting. The bar is replaced by the color setting choice from 1 to 5. Each color setting is adjusted at the factory to the stated Kelvin. If a setting is adjusted, the name of the setting will change from Kelvin to Custom.

Red, Green, Blue: NEC’s AccuColor Control System decreases or increases the monitor’s red, green or blue color guns depending upon which is selected. The change in color will appear on screen and the direction (decrease or increase) will be shown by the bars.

Geometry Controls

Geometry Controls Menu

The Geometry controls allow you to adjust the curvature or angle of the sides of your display.

Sides In/Out (pincushion): Decreases or increases the curvature of the sides either inward or outward.

Sides Left/Right (pincushion balance): Decreases or increases the curvature of the sides either to the left or right.

Sides Tilt (parallelogram): Decreases or increases the tilt of the sides either to the left or right.

Sides Align (trapezoidal): Decreases or increases the bottom of the screen to be the same as the top.

Rotate (raster rotation): Rotates the entire display clockwise or counterclockwise.

Tools 1

Moiré Canceler: Moiré is a wavy pattern which can sometimes appear on the screen. The pattern is repetitive and superimposed as rippled images. When running certain applications, the wavy pattern is more evident than in others. To reduce moiré, adjust the ON/Level by using the –/+ CONTROL buttons.

Basic Convergence: Aligns all three colors (R,G,B) to form a single color (white). The purpose of this control is to ensure that a white line drawn on the screen is as crisp and clear as possible.

Use the Horizontal control to adjust the alignment of the white lines in the up/down direction.

Use the Vertical control to adjust the alignment of the white lines in the left/right direction.

Area Convergence: A small window will appear to indicate the area of adjust- ment — Top Horizontal, Top Vertical, Bottom Horizontal or Bottom Vertical.

Corner Correction: Allows you to adjust the geometry of the corners of your display — Top, Top Balance, Bottom or Bottom Balance.

7

78134171

9

12/3/98, 4:10 PM

Image 9
Contents MultiSync Index FCC Information Canadian Department of Communications Compliance StatementContents Quick Start Turn off the power to your computerFigure A.2 USB downstream port Controls Brightness/Contrast ControlsSize and Position Controls Color Control/AccuColor Control System Geometry ControlsTools Controls Information Recommended Use Safety Precautions and MaintenanceRecommended Use Monitor MultiSync FP950 Specifications Specifications305 mm/12.0 inches Does not include border area Monitor MultiSync FP1350 SpecificationsFeatures Troubleshooting References 978FastFacts Information 800 Limited Warranty TCO’99 Why do we have environmentally labelled computers?Lead Röntgenstrahlung Informations FCC AvertissementGuide de l’utilisateur ContenuMise en marche rapide Mise en marche rapide suite Port USB de l’ordinateur Commandes Commandes de luminosité/contrasteCommandes de format et de position Commandes suite Commandes du menu GéométrieOutils Système Ipmmc Activé Information Consignes de sécurité et d’entretien Usage recommandéErgonomie Usage recommandé suite275 mm/10,8 pouces Fiche technique305 mm/12,0 pouces Fiche technique suiteFonctions Pas d’image Dépannage’image défile ou est instable ’image est floue ou les couleurs semblent brouilléesInformations FastFactsMC 800 RéférencesInfo docum. & vente NEC-INFO 800 Téléventes 800Garantie limitée Pourquoi des ordinateurs «éco-étiquetés»? TCO’99Qu’est-ce qu’implique l’éco-étiquetage? Exigences environnementalesPlomb TCO’99 suiteCadmium MercureDéclaration du fabricant Déclaration DE Conformité Informationen der FCC Federal Communications Commission WarnungBenutzerhandbuch LieferumfangDen Computer ausschalten Quick StartQuick Start / Fortsetzung Abbildung Bedienungselemente Helligkeits-/KontrastreglerGrößen- und Positionsregler Color Control / AccuColor Control System Bedienungselemente/FortsetzungGeometrie-Einstellungen WerkzeugeBedienungselemente/Fortsetzung Information Vorsichtsmaßnahmen und Wartung Empfehlungen für die VerwendungEmpfehlungen für die Verwendung / Fortsetzung Technische Daten Monitor Anmerkungen MultiSync FP950 Technische DatenTechnische Daten Monitor Anmerkungen MultiSync FP1350 Technische Daten / FortsetzungFunktionen Fehlerbehebung Verweise FastFacts-Information 800Tele-Vertrieb 800 Beschränkte Gewährleistung Warum haben wir umweltzertifizierte Computer? Worum geht es bei der Zertifizierung?Umweltkriterien Kadmium BleiQuecksilber FCKWs FreoneErklärung des Herstellers Konformitätserklärung 78134171 12/3/98, 411 PM 78134171 12/3/98, 411 PM 78134171 12/3/98, 411 PM Declaration of Conformity