NEC 790 manual Determining Battery Status, Recharging the Main Battery Pack

Page 41

Determining Battery Status

You can determine battery status by using the power icon on the lower right-hand side of the taskbar or through the power icon in the control panel. The icon on the taskbar displays as an electrical plug when the battery is fully charged (battery charging LED lights green) or as a battery while charging (battery charging LED lights amber).

To display battery status, use one of the following methods:

!Double tap the battery/plug icon on the taskbar, if present.

!Go to Start, Settings, Control Panel, and double tap the Power icon.

Recharging the Main Battery Pack

The main battery pack contains rechargeable Lithium-Ion cells. Recharge a battery pack when you see the following message displayed on your screen:

Main Batteries Very Low

To recharge a battery pack installed in the battery bay, connect the AC adapter. See “Connecting the AC Adapter” in Chapter 1.

The battery charging LED indicates the charging status of the main battery pack when the NEC MobilePro is connected to an AC power source. The LED status displays as follows:

!Lights amber while charging.

!Lights green when fully charged.

It takes approximately 4.5 hours to recharge a fully depleted battery pack regardless of the system's power state. However, if the main battery has been depleted for a prolonged period, you must allow 6-10 hours for the main and backup battery to fully recharge (see the section, “Recharging the Backup Battery”).

Note Through normal use, the capacity of a battery pack gradually declines. Should you notice that the battery does not stay charged as long as expected, it is probably necessary to replace the battery with a new one. Please refer to the section “Battery Replacement” later in this chapter. Depending upon use, a battery pack should recharge from full depletion approximately 300 times during the life of the battery.

2-10Introducing the NEC MobilePro

Image 41
Contents B I L E P R O 7 9 Proprietary Notice and Liability Disclaimer Contents Iv Contents Troubleshooting Specifications Index Using This Guide Using This GuideText Conventions Viii Using This GuideGetting Started Getting Started WelcomeUnpacking Your MobilePro NEC MobilePro Getting to Know Your MobileProLithium-Ion battery pack Installing and Charging the BatteryAccessories Inserting the battery pack Getting Started Connecting the AC Adapter Connecting the AC adapter Introducing the Software Taking a Quick TourVerifying PC Connection Settings Connecting to Your PC via SerialEnsuring the Availability of the Serial Port Connecting the PC Connect CableConnecting the PC connect cable Network Requirements Installing Microsoft ActiveSyncCreating a Partnership Verifying Synchronization SettingsConnecting to Your PC via Infrared Enabling the Infrared Port Modifying PC Connection SettingsSetting the Infrared Connection Speed Installing Microsoft ActiveSync Installing ActiveSync Creating a Partnership Synchronizing via the Serial Port Synchronizing with Your Host PCSynchronizing via the Infrared Port Resynchronizing Your MobileProConnecting Remotely Using other Communication DevicesHelp Resources Getting HelpPocket PC Magazine Buyer’s Guide Introducing NEC MobilePro Display panel Identifying System FeaturesAround the Front of the System Introducing the NEC MobilePro Keyboard panel and base unitStatus LEDs Around the Back of the SystemAround the Left Side of the System Features on the back of the systemLeft side features 6Introducing the NEC MobilePro Around the Bottom of the System Right side featuresAround the Right Side of the System Features on the bottom of the system Opening the Display Panel Using the StylusUsing MobilePros Power Sources Recharging the Main Battery Pack Determining Battery StatusMobilePro Power Management Recharging the Backup BatteryRemoving and Inserting the Battery Pack Battery ReplacementRemoving the battery pack Caring for the MobilePro Battery PrecautionsPrecautions Storage Requirements Routine CleaningIntroducing the NEC MobilePro Introducing Windows CE Introducing Windows CE Using Windows CEWindows CE Operating System Windows CE Desktop Dragging and DroppingPocket Applications Printing Features Creating a Network Ethernet Connection Network CapabilitiesMicrosoft ActiveSync Backing Up and Restoring Data Online HelpUsing the NEC MobilePro Using the NEC MobilePro Powering On and OffPowering on and off Adjusting the brightness Making Display Panel AdjustmentsBacklight Enabling the Suspend SwitchUsing the Keyboard Keyboard Default Application Shortcut Keys Using Application Shortcut KeysOther Function Keys Defining Application Shortcut KeysAdjusting MobilePro Settings Locating the Scroll Dial Using the Scroll DialMenu Selections Using the Voice RecorderRecording Memos Inserting PC Cards Using PC CardsVerify that the PC card is securely in the slot Inserting a PC cardInserting CompactFlash Cards Using CompactFlash CardsRemoving PC Cards Inserting a CompactFlash card Removing CompactFlash CardsUsing the IR Port Using the Soft Reset Button Resetting the MobileProSoft reset button Using the Full Reset ButtonBattery release latch Battery pack Battery release lock Full reset button Using the FlashROM Configuration UtilityUsing the NEC MobilePro Setting Up a Remote Connection Setting Up a Remote Connection Preparing for Connection SetupConnecting the Internal Modem Connecting the telephone cable Connecting to an Internet Service ProviderConnecting to a Remote Access Server Sending and Receiving Email Activating a Connection Tap Services again, if necessary and tap Connect Troubleshooting Troubleshooting2Troubleshooting Troubleshooting A-3 CPU SpecificationsPorts SpecificationsRecharge Time Specifications B-3Dimensions Specifications B-5 Regulatory Statements Regulatory Statements for U.S. and CanadaFCC Statement for United States Only FCC Part Regulatory Statements IC CS-03 FCC Warning Battery Disposal CTR21 Regulatory Statements for EuropeBattery Disposal Declaration of Conformity Index-1 IndexIndex-2 Index-3