Lexmark x5100 manual Energy Star

Page 70

Notices

Federal Communications Commission (FCC) compliance information statement

The Lexmark X5100 Series has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The FCC Class B limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

•Consult your point of purchase or service representative for additional suggestions.

The manufacturer is not responsible for any radio or television interference caused by using other than recommended cables or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user's authority to operate this equipment.

Note:To assure compliance with FCC regulations on electromagnetic interference for a Class B computing device, use a properly shielded and grounded cable such as Lexmark part number 1329605 for parallel attach or 12A2405 for USB attach. Use of a substitute cable not properly shielded and grounded may result in a violation of FCC regulations.

Any questions regarding this compliance information statement should be directed to:

Director of Lexmark Technology & Services Lexmark International, Inc. 740 West New Circle Road Lexington, KY 40550 (859) 232-3000

Industry Canada compliance statement

This Class B digital apparatus meets all

requirements of the Canadian Interference-Causing Equipment Regulations.

Avis de conformité aux normes d’Industrie Canada

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

European Community (EC) directives conformity

This product is in conformity with the protection requirements of EC Council directives 89/336/EEC and 73/23/EEC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility and safety of electrical equipment designed for use within certain voltage limits.

A declaration of conformity with the requirements of the directives has been signed by the Director of Manufacturing and Technical Support, Lexmark International, S.A., Boigny, France.

This product satisfies the Class B limits of EN 55022 and safety requirements of EN 60950.

The United Kingdom Telecommunications Act 1984

This apparatus is approved under the approval number NS/G/1234/J/100003 for the indirect connections to the public telecommunications systems in the United Kingdom.

ENERGY STAR

66

Page 69 Page 71
Image 70
Page 69 Page 71
Contents Lexmark X5100 All-In-One Series User’s Guide Safety information Contents Troubleshooting Setting up your All-In-One Learning about your All-In-OneUnderstanding the All-In-One parts Table on page 3 describes each partUse When you want to Understanding the operator panelPage Press When you want to Operator panel menus From this menu You canIRON-ON/MIRROR Using the Lexmark X5100 Series All-In-One Center Understanding the All-In-One softwareUsing Print Properties Using the Lexmark X5100 Series Photo Editor Using the Lexmark X5100 Series Solution Center Following table describes the LSC tabs Understanding the paper type sensor Click Printing Preferences or Properties Click OK Using your All-In-One Placing your document on the scanner glassLoading paper You can load up to Make sureYou can load up to Make sure Page Copying using the operator panel Copying using the All-In-One software Scanning using the operator panel Press E-mail, File, Software Scanning using the All-In-One software Click Scan Now Sending a fax using the operator panel PrintingSending a fax using the All-In-One software Creating projectsPrint a banner Using the All-In-One software Using the operator panelMake color copies Click Attach Now Enlarge or reduce needlepoint or woodworking patterns Scan multiple pages or images Print a poster Page Page Print mirror images and iron-on transfers Using your computerPersonalize fabric with pictures Networking Use Optical Character RecognitionMaintenance Replacing the print cartridgesPage Page Select Aligning the print cartridges Cleaning the print cartridge nozzlesAfter installing cartridges To improve print qualityUsing the operator panel Wiping the print cartridge nozzles and contacts Preserving the print cartridges Ordering suppliesSetup troubleshooting General troubleshootingProblem Go to Fax problems Paper misfeeds or multiple sheets feedEnvelopes do not feed properly Transparencies or glossy photo papers stick togetherTransparencies or photo papers contain white lines Document does not printDocument prints poorly Document prints slowlyVertical, straight lines are not smooth Print is too dark or smudged Characters are missing or unexpectedPrint quality is poor at the edges Display language is not preferable Colors are faded or not printing completelyCopy quality is unsatisfactory All-In-One or scanner is not communicating with computerIf your document is too light or too dark Page To turn the feature off for your next scan To clean the scanner glassTo adjust the auto-cropping To adjust cropping manually Edges of copied documents are cut offScanner unit will not close Copied objects appear in a different location onFit to Page function is not working properly If auto detect is set but not working correctlyYou receive an error message Paper Jam messageCover Open message Ink Low message Paper Out messageCartridge Error messages Unlock Scanner messageCheck the table below for specific instructions Uninstall and reinstall the All-In-One software Other error messagesOther help sources Energy Star Japanese Vcci notice Statement of Limited Warranty Limitation of liability Index Menu headings 6 messages, error Cartridge Pages or images
Top Page Image Contents