Emerson Remote Monitoring Panel user manual Current Record Window

Page 19

Operation

Table 12 Descriptions of RMP menus and data window items (continued)

	Menu
	Type	Item Type	Explanation
		Battery voltage (V)	Battery bus voltage
		Battery current (A)	Battery bus current
		Battery temperature (°C)	Battery temperature °C
	Battery	Remain Time Min.	Battery run time remaining
		Battery boost charging	Battery is boost charging
		Battery float charging	Battery is float charging
		Battery disconnected	Battery is not connected
	Records	(history log)	Displays all records in the history log
	Language	(choices for text displayed)	User may select any of 12 languages for LCD text.
		Display contrast	Adjust the LCD display contrast
		Date format set *	Choose the format for date display: M/D/Y, D/M/Y, M/D/Y, Y/M/D
		Date & time *	Set the date and time
		Comm1 baud rate *	Communication baud rate setting for IntelliSlot 1
		Comm2 baud rate *	Communication baud rate setting for IntelliSlot 2
		Comm3 baud rate *	Communication baud rate setting for IntelliSlot 3
		Communication address *	This setting is applicable to RS485 communication mode
	Settings	Communication mode *	Communication Mode Setting
	Settings	Callback times *	When IntelliSlot 1 Communication mode is Modem, this parameter sets

			the number of times a number is redialed to send an alarm notification.


		Phone No.1 *	When IntelliSlot 1 Communication mode is Modem, this is the first phone
		Phone No.1 *	number to be dialed (to send an alarm notification).
			number to be dialed (to send an alarm notification).
		Phone No.2 *	When IntelliSlot 1 Communication mode is Modem, this is the second
		Phone No.2 *	phone number to be dialed (to send an alarm notification).
			phone number to be dialed (to send an alarm notification).
		Phone No.3 *	When IntelliSlot 1 Communication mode is Modem, this is the third phone
		Phone No.3 *	number to be dialed (to send an alarm notification).
			number to be dialed (to send an alarm notification).
		Command password *	User can modify the command password.
		Battery maintenance test *	This test performs a partial discharge of the battery to obtain a rough
			estimate of the battery capacity. Load must be between 20% and 100%.
		Battery capacity test *	This test performs a full discharge of the battery to obtain a precise
		Battery capacity test *	measure of the battery capacity. Load must be between 20% and 100%.

	Command	System test *	This is a self-test of the UPS. When the user activates this function, a
	Command	System test *	popup window appears about 5 seconds later to show the results.
	(start/stop
	battery &	Stop testing *	Manually stops a battery maintenance test, battery capacity test or system
	system	Stop testing *	test.
	system		test.
	tests)
	tests)	Freshening Charge *	This command will allow a temporary Equalize charge for the batteries.

			This charge is configurable for 1 to 36 hours
			This charge is configurable for 1 to 36 hours
		Stop Freshening Charge *	Manually stop a Freshening Charge
		Modem Auto-answer	Manually enable the auto-answer function of modem.
		enable *	Manually enable the auto-answer function of modem.
		enable *
		UPS version	Provides UPS firmware version numbers for the inverter, rectifier and
	Version	UPS version	software display board.
	Version		software display board.
		UPS model	Provides UPS model information—for example, 400V-50Hz.

* Visible from the RMP, but the control is available at UPS only.

Current Record Window

Keeps a log the events that resulted in the current mode of operation. Ignores transient conditions that have been resolved. Use “page” (F1) and up / down arrow to read the events.

For a complete history log, refer to the Records tab of the Menu and Data Window. Refer to Table 13 for a complete list of supported status messages.

15

Image 19

Contents

Liebert Remote Monitoring Panel Page Table of Contents Figures Information for the Protection of the Environment Introduction RMP component location in Figure UPS Room Maintenance or Control RoomPreliminary checks Power Supply15.6mm 14mm Cable Specifications Communication cable specificationsUPSU2J24 Mounting the RMP on DrywallElectrical connections Power and communication cable routingCommunication connections On Remote Monitoring Panel board RS-485 cable connection to Liebert NXOpening screen Startup and ResetSilence On/Off screens UPS and RMP firmware are compatible screenCommunication with UPS failed Audible Alarms-Buzzer LED Mimic Power FlowMenu key Icons and their meaning LCD Monitor and Menu KeysKey Help Window Type Stop Freshening Charge Freshening ChargeMenu Type Item Type Explanation Detailed Description of Menu ItemsUPS system window Descriptions of RMP menus and data window itemsCurrent Record Window RMP messages Status and Event MessagesMessage Description / Suggested Action if any Condition is no longer true EPO RMP messages Prompt windows, meanings controlled at RMP Dynamic Energy Flow Chart and UPS Help ScreenPrompt Popup Windows Prompt windows, meanings controlled at UPS onlyHelp screen Default screen saverCable specifications Mechanical specificationsEnvironmental specifications Electrical specificationsElectromagnetic interference EMI-emission limits Agency and CertificationsElectromagnetic susceptibility EMS-immunity levels Er t Ne tIti Ti n