Philips 241B4LP Power on light is too strong and is disturbing, Reconnect your USB peripherals

Page 46

8.Troubleshooting & FAQs

Horizontal flicker appears

•Adjust the image using the “Auto” function in OSD Main Controls.

•Eliminate the vertical bars using the Phase/ Clock of Setup in OSD Main Controls. It is valid only in VGA mode.

Image appears blurred, indistinct or too dark

•Adjust the contrast and brightness on On-Screen Display.

An "after-image", "burn-in" or "ghost image" remains after the power has been turned off.

•Uninterrupted display of still or static images over an extended period may cause " burn in", also known as "after-imaging " or "ghost imaging", on your screen. "Burn-in", "after- imaging", or "ghost imaging" is a well-known phenomenon in monitor panel technology. In most cases, the "burned in" or "after-imaging" or "ghost imaging" will disappear gradually over a period of time after the power has been switched off.

•Always activate a moving screen saver program when you leave your monitor unattended.

•Always activate a periodic screen refresh application if your monitor will display unchanging static content.

•Severe” burn-in” or “after-image” or “ghost image” symptoms will not disappear and cannot be repaired.The damage mentioned above is not covered under your warranty.

Image appears distorted.Text is fuzzy or blurred.

•Set the PC’s display resolution to the same mode as monitor’s recommended screen native resolution.

Green, red, blue, dark, and white dots appears on the screen

•The remaining dots are normal characteristic of the liquid crystal used in today’s technology, Please refer the pixel policy for more detail.

The "power on" light is too strong and is disturbing

•You can adjust “power on” light using the power LED Setup in OSD main Controls.

Audio problem

No sound

•Check if audio cable is connected to PC and monitor correctly.

•Ensure audio is not muted. Press OSD “Menu”, select “Audio” then “Mute”. Check it on “Off” position.

•Press “Volume” in OSD main control to adjust the volume.

USB problem

USB peripherals are not working

•Check if USB upstream cable is connected to your monitor correctly

•Turn your monitor OFF and ON once again. You may need to install/reinstall USB drivers in your PC and ensure hub is active.

•Reconnect your USB peripherals

For further assistance, refer to the Consumer Information Centers list and contact Philips customer service representative.

44

Page 45 Page 47
Image 46
Page 45 Page 47
Contents 241B4LP Table of Contents Temperature 0-40C 32-95F Humidity 20-80% RH Safety precautions and maintenanceOperation Notational Descriptions Weee Setting up the monitor Setting up the monitor VGA 100mm PivotRemove base stand and base Remove the base stand 100mm Except using key to scroll down, you can also Why do I need it?How does it work? Off No optimization by SmartImage What is it? SmartSharpnessPhilips SmartControl Premium First launch -WizardImage Optimization Image Optimization ECO Image Optimization OptionAuto Pivot Facoty Preset can also be called from the drop down menu Task Tray Menu Enabled Other alternative path Vista Drag and Drop WindowsWin No other alternative path available Title Bar Options Display Tune from the start menu or short cut on the desktopLeft Click Menu SmartDesktop Partition Definitions Right side Vertical Horizontal Split TopLeft side Vertical Right side Vertical Even SplitCustom settings Setting Default settingsYou can return to the default mode at any Time setting YES TFT-LCDLED USB12W Energy Consumption 0BTUMtbf Rohs YES Epeat640x480 Automatic PowerSaving Automatic power saving featureLead-free Product For more information, please visit2006/95/EC Low Voltage Directive 2004/108/EC EMC Directive Epeat Electronic ProductBenefits of Epeat Product also comply with the following standardsFederal Communications Commission FCC Notice U.S. Only Reorient or relocate the receiving antennaCommission Federale de la Communication FCC DeclarationVaroitus Polish Center for Testing and Certification NoticePaikka/Ilmankierto Plassering/VentilasjonErgonomie Hinweis nur Deutschland Achtung Beim AufstellenTypes of Pixel Defects Philips Flat Panel Monitors Pixel Defect PolicyPixels and Sub pixels Bright Dot DefectsDark subpixel Black Dot DefectsTotal bright dot defects of all types Adjacent dark subpixels0810 Belgium Care Contact Information for Western Europe regionAustria Siemens I&S 078 Denmark Novo Fujitsu IBA CPS Contact Information for Apmea region AL Shahd Computer L.L.CTroubleshooting No Picture Power LED not litPower on light is too strong and is disturbing Reconnect your USB peripheralsSmartControl Premium FAQs Run Windows Update and updated monitor and/or video driverTroubleshooting & FAQs Icm? Q4 How do I adjust the resolution? Q9 Can the Philips monitor be mounted on the wall? Q7 How should I clean the monitor surface?Q10 Can I connect my monitor to any PC, workstation or Mac? Troubleshooting & FAQs
Top Page Image Contents