Philips 27HT7210D · USE Channel Table no / YES, · D Igital TV Label no / YES, DTV Setup

Page 13

TV SETUP MENU & SUB-MENUS (CONTINUED)

·USE CHANNEL TABLE (NO / YES)

If USE CHANNEL TABLE is set to NO. The digital tuner will ignore the Virtual Channel Table (VCT) information that is contained in the Program and System Information Protocol (PSIP) during channel installation or Direct Channel Command which is sent by the TV set.

When VCT is ignored, the digital tuner will tune to the physical channel, Radio Frequency (RF) Channel. Program Map Table (PMT), which is stored as channel number Major dot Minor (eg. 2.1) in the TV set. The virtual channels will not be used in this case.

If USE CHANNEL TABLE is set to YES. Program and System Information Protocol (PSIP) is used during channel installation, and Direct Channel Command.

The digital tuner will use the virtual channel information that is contained in the PSIP, to map the virtual channels to the physical channels, which is also called Major dot Minor channel in this case.

For more information on the PSIP, you can refer to ATSC Standard, Program and System information Protocol for Terrestrial Broadcast and Cable (Revision B), which can be found at the website http://www.atsc.org/standards/a_65b.pdf.

·D IGITAL TV LABEL (NO / YES)

If DIGITAL TV LABEL is set to NO. The Digital TV channel number will not be displayed on the screen.

If DIGITAL TV LABEL is set to YES. The Digital TV channel number will be displayed on the top right hand corner of the TV screen for about 5 seconds whenever there is a change in digital TV channel.

For the changes in the Digital TV label to take effect, please conduct a cold / warm start when the setting is changed from Yes to No, vice versa.

DTV SETUP

Entering the DTV SETUP menu allows you to edit features while you are in Digital TV mode.

C HANNEL EDIT

Channel edit allows you to add or skip channels from your favorite list.

1Press CURSOR > or < to toggle between Added or Skipped. If Skipped is selected, the channels will

be skipped when scrolling channels with the CH+ or CH- . If Added is selected, the channels will not be skipped when scrolling channels with the CH+ or CH-

Note : When you are in Digital Mode you can only add or skip programs in Digital Channels.

Weak Dig Sig

Digital broadcasting is still new. Therefore it is not uncommon for a broadcaster to only send out a digital signal for part of a day The reception could also come and go. If you program your channels when the signal is not being sent or is weak it will not be saved in your channel setup. Using the Weak Digital Signal feature here, you can add those channels with weak or no signals to your channel list. Adding or skipping Weak Digital Signal can ONLY be done in

Digital Mode

AutoLock (not supported)

Fact Ch Reset

Factory Channel Reset feature lets you erase the contents of the master, user and favorite channel lists. This restores the TV to the initial state before the first Auto Program operation For instructions on how to Auto Install the TV again, refer to page 12.

Digital Audio

Digital Audio allows you to switch to another audio language when it is available.

Timer (not supported)

Closed Caption

Closed Caption lets you select the default option or options that you have assigned to your Close captioning service. This

feature is ONLY available in Digital Mode.

Emergency Alert

Emergency Alert lets you display or discard emergency alerts for Low or Medium priority.

Note : Emergency Alert will not be visible if no broadcast is received or when the TV is in Standby mode.

13

Image 13
Contents Model No Serial No Philips Business Display SolutionsTable of Contents Important Safety Instructions Safety Information Safety Information and Useful TipsSuggested Steps to Take Before Calling ServiceSwitching on the SET USE & Care of Remote ControlBasic Television Connection Antenna ConnectionApplicable to 27HT4000D/27 only Rear Jack Panel ConnectionsRC2888/01 Guest-Mode RemoteRC2573GR optional Remote ControlsLOW Battery Check Guest Remote Control KeysService Remote Battery OK Select a channel number Activating TV Setup MenuTV Setup Main Menu TV Setup Menu & SUB-MENUS · USE Channel Table no / YES DTV Setup· D Igital TV Label no / YES Hannel Edit· Audio OUT Fixed NO/ YES Noise RE D Uction no / YES· Speaker Mute no Ultra Bass no / YES· Audio / Video OUT Mute no / YES · Keyboard Lock no / YES· Monitor OUT RF no / YES · Welcome Message · Channel Guide no / YES / Power onDisplay ClearReminder no / YES · A/CH A/V Switch no / YES· 3 Digit Entry no / YES · Save CC no / YES· V-CHIP Menu Item no / YES Chip Setup no / YES· Saved V-CHIP no / YES TV-54 · Security Standard / High19.72 29.29 23.35 27HT4000D/27 Dimensions19.8 28.98 22.83 27HT7210D/27 DimensionsDEFINITIONS, Acrynyms & Abbreviations Rtsp RTP Limited Warranty Cleaning & CareEND-OF-LIFE Disposal Index