Philips user manual Philips 150P3D 150P3E

Page 44

Regulatory Information

Energy Star Declaration

PHILIPS 150P3D 150P3E

This monitor is equipped with a function for saving energy which supports the VESA Display Power Management Signaling (DPMS) standard. This means that the monitor must be connected to a computer which supports VESA DPMS to fulfill the requirements in the NUTEK specification 803299/94. Time settings are adjusted from the system unit by software. From indicated inactivity to Power Saving Position A2, the total time must not be set to more than 70 minutes.

NUTEK

VESA State

LED Indicator

Power Consumption

Normal operation

ON

Green

< 30 W

Power Saving

Suspend

Amber

< 2 W

Position A1

 

 

 

Power Saving

OFF

Amber

< 2W

Position A2

 

 

 

As an ENERGY STAR® Partner, PHILIPS has determined that this product meets the ENERGY STAR® guidelines for energy efficiency.

We recommend you switch off the monitor when it is not in use for quite a long time.

RETURN TO TOP OF THE PAGE

Federal Communications Commission (FCC) Notice (U.S. Only)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Use only RF shielded cable that was supplied with the monitor when connecting this monitor to a computer device.

To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or excessive moisture.

THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE-CAUSING EQUIPMENT REGULATIONS.

file:///D/03771/english/150p3de/safety/regs/regulat.htm (5 of 10) [9/13/2002 1:42:07 PM]

Image 44
Contents File///D/03771/english/150p3de/index.htm 9/13/2002 14134 PM Safety and Troubleshooting Information Safety precautions and maintenanceInstallation Locations Notational Descriptions About This ManualAbout This Guide Return to TOP Product Information Product FeaturesTechnical Specifications Resolution & Preset Modes VideoAutomatic Power Saving Vesa Mode Video Sync Power Used LED colorPhysical Specifications Pin AssignmentSignal Assignment Product Views Physical FunctionHeight adjustment Portrait display Rotate the monitor body 90 degrees counter clockwise Return to TOP Installing your LCD Monitor Front View Product DescriptionOptimizing Performance OSD Tree On-Screen DisplayDescription of the On Screen Display Page Digital signal input Page Customer Care & Warranty North America Canada USAColor temperature GlossaryEnergy Star Computers Programme Device Vertical refresh rate Installing Your LCD monitor driver Download and PrintPrinting instructions Installing FPadjust Program To install FPadjust ProgramFAQs Frequently Asked Questions General FAQsFAQs Frequently Asked Questions Screen Adjustments Compatibility with other Peripherals LCD Panel Technology FAQs Frequently Asked Questions Ergonomics, Ecology, and Safety Standards Return to TOP Imaging Problems TroubleshootingCommon Problems An after-image remains after the power has been turned off Horizontal flicker appearsScreen is too bright or too dark An after-image appears Green, red, blue, dark, and white dots remainsPage Regulatory Information Environmental Requirements TCO 99 Information CE Declaration of Conformity Philips 150P3D 150P3E EN 55022 Compliance Czech Republic Only MIC Notice South Korea Only Varning Bsmi Notice Taiwan Only Earthed Information for Users outside the U.S Other Related InformationInformation for Users in the U. S Philips Pixel Defect Policy Philips Flat Panel Monitors Pixel Defect PolicyPixels and Subpixels Types of Pixel DefectsProximity of Pixel Defects Pixel Defect TolerancesTotal DOT Defects Connecting to Your PC Accessory PackConnecting to Your PC Return to TOP Remove the Base Remove and Re-install the BaseCondition Return to TOP Re-install the Base Return to TOP Getting Started Getting StartedFor Windows XP Return to TOP Accessories optional Accessories optionalProtective Cover Return to TOP Ergo Base Height adjustment Portrait display Multimedia Base TiltSwivel Height adjustment Portrait display Rotate the monitor body 90 degrees counter clockwise USB Hub About this productPower Socket For the supplied AC Adapter jack to connect to InstallationUSB connection Power connectionSetup Return to TOP Your International Philips F1rst Choice Warranty Thank you for purchasing this Philips monitorYour International Guarantee Limited Warranty Computer Monitor WHO is COVERED? What is COVERED?Before Requesting Service Philips Customer Care Center, P. O. Box 2976, Longview, TX F1rst Choice Contact Information Consumer Information Centers Eastern EuropeBrasil Canada Fax 21-656 NEW ZealandPhone 91-20-712 2048 ext Fax 91-20-712 Hong KongDomestic toll free 1-800-10-PHILIPS or 1-800-10-744 KoreaAfrica Dubai