Philips 150P3E Safety and Troubleshooting Information, Safety precautions and maintenance

Page 2

Safety & Troubleshooting

Safety and Troubleshooting Information

Safety Precautions and Maintenance • Installation Locations • FAQs • Troubleshooting • Regulatory Information • Other Related Information

Safety precautions and maintenance

WARNING: Use of controls, adjustments, or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards, and/or mechanical hazards.

Read and follow these instructions when connecting and using your computer monitor:

●Unplug the monitor, if you are not going to use it for an extensive period of time.

●Unplug the monitor, if you need to clean it with a slightly damp cloth. Wiping the screen with a dry cloth is possible when the power is off. However, never use alcohol, solvents, or ammonia-based liquids.

●Consult a service technician if the monitor does not operate normally when following the instructions in this manual.

●The casing cover should be opened only by qualified service personnel.

●Keep the monitor out of direct sunlight and away from stoves or any other heat source.

●Remove any object that could fall into the vents or prevent proper cooling of the monitor’s electronics.

●Do not block the ventilation holes on the cabinet.

●Keep the monitor dry. To avoid electric shock, do not expose it to rain or excessive moisture.

●When positioning the monitor, make sure the power plug and outlet are easily accessible.

●If turning off the monitor by detaching power cable or DC power cord, wait for 6 seconds, then attach the power cable or DC power cord for normal operation.

●To avoid the risk of shock or permanent damage to the set, do not expose the monitor to rain or excessive moisture.

●When positioning the monitor, make sure the power plug and outlet are easily accessible.

●IMPORTANT: Always activate a screen saver program during your application . If a still image in high contrast remains on the screen for an extended period of time, it may leave a so called "after-image" or "ghost image" in front of the screen. This is a well-known phenomenon that is caused by the shortcomings inherent in the LCD technology. Most of the time the after-image will disappear gradually over a period of time after switching off the power. Be aware that the after-image symptom can not be repaired and is not covered under warranty.

Consult a service technician if the monitor does not operate normally when operating instructions of this manual are followed.

RETURN TO TOP OF THE PAGE

file:///D/03771/english/150p3de/safety/safety.htm (1 of 2) [9/13/2002 1:41:35 PM]

Page 1 Page 3
Image 2
Page 1 Page 3
Contents File///D/03771/english/150p3de/index.htm 9/13/2002 14134 PM Safety and Troubleshooting Information Safety precautions and maintenanceInstallation Locations Notational Descriptions About This ManualAbout This Guide Return to TOP Product Information Product FeaturesTechnical Specifications Resolution & Preset Modes VideoAutomatic Power Saving Vesa Mode Video Sync Power Used LED colorPhysical Specifications Pin AssignmentSignal Assignment Product Views Physical FunctionHeight adjustment Portrait display Rotate the monitor body 90 degrees counter clockwise Return to TOP Installing your LCD Monitor Front View Product DescriptionOptimizing Performance OSD Tree On-Screen DisplayDescription of the On Screen Display Page Digital signal input Page Customer Care & Warranty North America Canada USAColor temperature GlossaryEnergy Star Computers Programme Device Vertical refresh rate Installing Your LCD monitor driver Download and PrintPrinting instructions Installing FPadjust Program To install FPadjust ProgramFAQs Frequently Asked Questions General FAQsFAQs Frequently Asked Questions Screen Adjustments Compatibility with other Peripherals LCD Panel Technology FAQs Frequently Asked Questions Ergonomics, Ecology, and Safety Standards Return to TOP Imaging Problems TroubleshootingCommon Problems Screen is too bright or too dark An after-image appears An after-image remains after the power has been turned offHorizontal flicker appears Green, red, blue, dark, and white dots remainsPage Regulatory Information Environmental Requirements TCO 99 Information CE Declaration of Conformity Philips 150P3D 150P3E EN 55022 Compliance Czech Republic Only MIC Notice South Korea Only Varning Bsmi Notice Taiwan Only Earthed Information for Users outside the U.S Other Related InformationInformation for Users in the U. S Pixels and Subpixels Philips Pixel Defect PolicyPhilips Flat Panel Monitors Pixel Defect Policy Types of Pixel DefectsProximity of Pixel Defects Pixel Defect TolerancesTotal DOT Defects Connecting to Your PC Accessory PackConnecting to Your PC Return to TOP Remove the Base Remove and Re-install the BaseCondition Return to TOP Re-install the Base Return to TOP Getting Started Getting StartedFor Windows XP Return to TOP Accessories optional Accessories optionalProtective Cover Return to TOP Ergo Base Height adjustment Portrait display Multimedia Base TiltSwivel Height adjustment Portrait display Rotate the monitor body 90 degrees counter clockwise USB Hub About this productPower Socket For the supplied AC Adapter jack to connect to InstallationUSB connection Power connectionSetup Return to TOP Your International Philips F1rst Choice Warranty Thank you for purchasing this Philips monitorYour International Guarantee Limited Warranty Computer Monitor WHO is COVERED? What is COVERED?Before Requesting Service Philips Customer Care Center, P. O. Box 2976, Longview, TX F1rst Choice Contact Information Consumer Information Centers Eastern EuropeBrasil Canada Fax 21-656 NEW ZealandPhone 91-20-712 2048 ext Fax 91-20-712 Hong KongDomestic toll free 1-800-10-PHILIPS or 1-800-10-744 KoreaAfrica Dubai
Top Page Image Contents