Black Box LE14XXA, Modular Switches manual Factory Settings

Page 27

Black Box Modular SwitchesInstallation and User Guide (8/99)

Therefore, the default setting of auto-negotiation (copper ports) is generally desirable because it is widely used and allows for the connection of various devices without re- configuration. Under certain conditions,(where the connected device is full duplex and does not support Auto-negotiation; or the connected device does not support Auto-negotiation properly no auto-negotiation is better and the internal jumper settings will permit this to be selected on a per-port basis.

See Section 4.4 for additional information on auto-negotiation functionality.

3.5 Fiber ports, internal jumper settings for 100Mb fixed Half- or Full-Duplex, per port

The factory (or default) setting is for full-duplex on all fiber 100Mbps ports, which is generally popular. It works well under most circumstances, but cannot always be depended upon to wor as expected. If full-duplex will not function properly in your setup, internal jumpers allow the speed and mode of the LE14XXA-Series fiber 4-ports to be

Jumper Settings for 100Mbps Fiber Half or Full Duplex

Jumper

Port

 

Function

 

Factory Settings

Speed

 

 

 

 

 

 

 

 

 

 

 

JP1-2, 6-7, 9-10

Pin 1-2, 6-7, 9-10

FDX @100 config

 

YES

 

100 Mb

JP1-2, 7-8, 11-12

Pin 1-2, 7-8, 11-12

HDX@100 config

 

NO

 

100 Mb

 

Factory Settings

100Mbps Full

 

100Mbps

Half

 

Duplex

 

Duplex

 

 

 

J1

 

 

J1

 

 

 

 

 

 

100 Mb

100 Mb

1 2 3 4

1 2 3 4

J1

9 10 11 12

5 6 7 8

1 2 3 4

Jumper Settings for HDX/FDX

J1 J2 J3 J4

Bottom QPM Retaining

Printed Circuit card

TOP

1

2

3

4

Two(50) Pin

QPM Connectors (inserts into main board)

LED

Figure 3.5. Fiber ports, internal jumper settings. Note: Be certain that the main power is disconnected before opening the unit or changing any internal jumper settings

21

Image 27
Contents Modular Switches Contacting Black Box Corporation TrademarksFCC Statement Black Box Modular Switches Installation and User Guide 8/99 Table of Contents Troubleshooting Network Standards Technical Specifications PerformanceConnectors for copper wiring Fiber Multi -mode connector types48VDC Power Supply Optional Fiber Single-mode connector typesManual switch -selections and jumpers Power Supply InternalAgency Approvals WarrantyLE1416A Model InformationLE1401A LE1408AIntroduction Inspecting the Package and Product LE14XXA-Series chassis models Product Description , 8-port and 16-port Modular SwitchesModular Switches 4-port modules, 100Mb fiber Fiber 4-Port Modules, LE1420C, LE1419C LE1423C LE1422C4-port modules, 10 Mb fiber Combo 4 Port Modules, 3 + 1, 3 RJ-45 and 1 fiber port 4 4-Port Module, RJ-45 copperFrame Buffering and Latency Page Port, 12-port, 8-port and 4-port models Plug-and-Play installation for high performance switchingFront-mounted LEDs, world-wide AC power supply Full-duplex or Half-duplex operation, auto-sensingExample 1 LE1401A ApplicationsXample 2 8-port LE1408A Example 3 16-port LE1416A 4c LE1416A provides a 100Mb mixed-media backbone SwitchLocating LE14XXA-Series Switches InstallationCopper Connecting Ethernet MediaConnecting Fiber Optic ST-type, twist-lock Ieee Standard Media Type Max. Distance Port Module FiberConnecting Fiber Optic S C-type, Snap-In Connecting Single-Mode Fiber OpticMedia Ieee Standard Connector Magnum LE1401A, optional Table-Top or Shelf MountingWall or Vertical Surface Mounting, 8-port LE1401A Proper mountingFactory Settings 10/100 Mbps Factory Settings For RJ-45 Factory Settings 10Mbps Half- Duplex Powering the LE14XXA-Series Switch 10Mbps Fiber ports internal jumper settingsPage Gure 3.9.1a Removing Hassis Cover Port Module 4PM InstallationPreparation for Installing and Removing 4PMs Ep 2. Remove Chassis Cover1c Front View 4PM Retaining Screws hold Face PlatesInstalling 4PM Cards in the LE14XXA-Series Inserting 4PM Cards Into a LE1416A 2b Top View 4PM Module Installed inside a LE1416A4PM Cards Switching Functionality Filtering and ForwardingAddress Learning Steady ON, Link status for 10 Mbps and 100Mbps operation Power LED, on when AC power is applied to the unitStatus LEDs For all LE14XXA-Series modelsGeneral information Flow-control, Ieee 802.3x standard Auto-negotiation for 10 Mb ports, half- or full-duplex modeDistanc Module Product Description Introduction LE14XXA-Series 4-Port Modules4PMIEEE-specified 100Mbps shared-collision LE1421C 100Mbps single-mode FX-S C-type, snap-in connector Small-form-factor LE1425C Twisted Pair, 10/100Mb TP 4-Port 10/100BASE-T and 100BASE-FX Combo Quad-Port Connectors Fety, etc 10 4PM-FPBefore Calling for Assistance TroubleshootingShipping and Packaging Information When Calling for AssistanceBlack Box Corporation

LE14XXA, Modular Switches specifications

The Black Box LE14XXA series of modular switches are designed for high-performance networking in both small and medium enterprises, as well as in larger data center environments. These switches stand out due to their scalability, flexibility, and robust functionality, making them suitable for a variety of applications.

One of the main features of the LE14XXA modular switches is their modular design, allowing for the integration of various interface cards to tailor the switch to specific networking needs. This flexibility ensures that organizations can adapt their network architecture as requirements evolve, making it a future-proof investment. The switches support a range of modules, including Ethernet, fiber optics, and PoE (Power over Ethernet), which can be easily swapped out or added to support changing technology demands.

In terms of performance, the LE14XXA series offers impressive throughput capabilities, often supporting up to 10 Gbps per port. This speed is critical for businesses that rely on fast data transfer rates for tasks such as video conferencing, large file transfers, and real-time applications. The switches also feature advanced Layer 2 and Layer 3 functionalities, facilitating efficient data routing and switching, which is essential for maintaining effective network performance.

Security is another critical characteristic of the Black Box LE14XXA switches. They incorporate a variety of security protocols, including 802.1X port-based access control, VLAN support, and secure management interfaces, which help protect sensitive data and ensure compliance with industry standards. This makes them an excellent choice for organizations that prioritize data protection and regulatory compliance.

Ethernet redundancy protocols, such as Spanning Tree Protocol (STP) and Rapid Spanning Tree Protocol (RSTP), enhance network reliability by providing failover options in case of link failures. Additionally, the LE14XXA switches feature energy-efficient designs that comply with energy-saving standards, which can significantly reduce operational costs over time.

User-friendly management interfaces, including a web-based GUI and command-line interface (CLI), simplify the configuration and monitoring processes. This ensures that IT administrators can efficiently handle the network without extensive training or experience.

Overall, the Black Box LE14XXA modular switches combine advanced technology, security features, and versatile design, making them a powerful choice for modern networking needs. Their adaptability and high performance offer businesses the capability to build scalable and secure networks that can grow alongside their operations.