Xerox 115, 100, 135 manual Table A-4. Throughput data DP155, Table A-5. Throughput data DP180

Page 111

Supplies

Table A-3. Throughput data DP135 (Continued)

Pitch

Paper width

Speed

 

 

 

3

15.31 to 17 in / 389 to 432 mm

58 ppm

 

 

 

Table A-4. Throughput data DP155

Pitch

Paper width

Speed

 

 

 

6

7 to 10.19 in / 178 to 259 mm

154 ppm

 

 

 

5

10.19 to 12.12 in / 259 to 308 mm

128 ppm

 

 

 

4

12.12 to 15.31 in / 308 to 389 mm

103 ppm

 

 

 

3

15.31 to 17 in / 389 to 432 mm

77 ppm

 

 

 

Table A-5. Throughput data DP180

Pitch

Paper width

Speed

 

 

 

8

7 to 7.4 in / 178 to 188 mm

206 ppm

 

 

 

7

7.4 to 9.01 in / 188 to 229 mm

180 ppm

 

 

 

6

9.01 to 10.19 in / 229 to 259 mm

154 ppm

 

 

 

5

10.19 to 12.12 in / 259 to 308 mm

128 ppm

 

 

 

4

12.12 to 15.31 in / 308 to 389 mm

103 ppm

 

 

 

3

15.31 to 17 in / 389 to 432 mm

77 ppm

 

 

 

Each time a job requires a different paper size that changes across a pitch boundary, the system performs a time-consuming xerographic quality adjustment. When the printing speed of an LCDS job appears to degrade due to the use of mixed stock sizes, you may be able to improve the speed by using the LCDS OUTPUT command TMODE parameter in the JSL to run the print job in a lower pitch mode. Refer to the OUTPUT TMODE parameter in Using LCDS Print Description Language for information on using this LCDS command.

Similarly, if the system cycles down frequently because your external finishing equipment has a slower throughput rate than the printing system, you can use the TMODE parameter of the LCDS OUTPUT command to lower the pitch mode to match the speed of the finishing equipment. This can improve overall throughput by avoiding time-consuming cycle downs.

NOTE: Pitch mode changes are supported only for LCDS printing.

Installation Planning Guide

A-5

Image 111
Contents 701P21121 Version 3.7 July EPSPage Table of contents Printer components and options Preparing for installationController requirements and specifications Printer requirements and specificationsInstallation System connectionsSupplies Table of contents Laser safety SafetyOzone information U. S. only Operation safety U. SOperation safety Europe Operator accessible areas Electrical supplyVentilation Maintenance Before cleaning your productCE mark Europe only Radio and telecommunications equipment directive Europe only For further information Safety Xiv Installation Planning Guide Contents IntroductionAbout this guide Conventions Page Introduction Xviii Installation Planning Guide System overview Product overviewSystem components Data stream resolutionProduct overview EPS DocuPrint 100/ 115/135/155/180Maximum throughput Throughput speedSupported hardware and operating systems Client workstations and system softwareClient networking software Micr printing featuresMicr fonts Example of a check printed with Micr line U. SCMC7 fonts Unsupported featuresIPS/NPS Micr fonts Lcds Micr fonts E13B fontsHost connectivity options Remote diagnosticsController overview Controller components and optionsSun Blade 1000/ 2000 configuration Controller componentsSun Blade workstation Page Sun Blade 2500 controller Sun Blade 2500 configurationPage Drive locations on the Sun Blade 1000/2000 Processor DVD-ROM drive location on Sun Blade Processor Back panel of the Sun Blade 1000/2000 controller Back panel of Sun Blade Optional processor components Controller interface options Online interfaceTape drive option Peripheral cabinet with tape drives Printer components Printer components and optionsPrinter control console Printer control console Printer with inverter feeder/stacker and one feeder/stacker Printer configurationsPaper stocks Bypass transport optionFunction Bypass transportRoll feeder support DP155 and DP180 EPS only Bypass transport printer configurationsResponsibilities Preparing for installationSite selection InstallationService Xerox responsibilitiesSystems training OperatorWeek Activity Responsibility Completed Installation planning checklistInstallation planning checklist DateConnectivity requirements Ethernet specificationsChannel-attached specifications Token Ring specificationsPower requirements Controller requirements and specificationsMultinational wall outlet configurations Outlet configurationsEnvironmental specifications Sun Blade 2500 environmental requirements Temperature Space requirementsSun Blade 1000/2000 environmental requirements Guidelines for controller placement Controller placementSun Blade 1000/2000 fan and vent locations to keep clear Do not Sun Blade 2500 fan and vent locations to keep clear50 Hz Controller hardware specifications and requirements summarySun Blade 1000/2000 specifications 60 HzSun Blade 1000/2000 specifications Printer 20 ft Sun Blade 2500 specifications60 Hz Power 8 ft Interface toSun Blade 2500 specifications Page Printer electrical requirements Printer requirements and specificationsOutlet configurations Printer 60 Hz voltage requirements at power outletHz printer outlet voltages 60 Hz Hz power configuration-50 ampPrinter 50 Hz WYE Star 380 and 400 voltage 50 Hz Printer 50 Hz WYE Star 415 voltagePrinter environmental specifications Condition RangeStandby Printer configurations available Printer requirements and specifications Printer requirements and specifications Printer requirements and specifications Bypass transport dimensions Bypass transport specificationsBypass transport dimensions Bypass transport space planning diagram top view Bypass transport paper path Configuration diagrams with bypass transport Space planning guidelines Shared space between components Clearance space requirements11. Back-to-back shared service area space Shared space configuration diagrams12. Face-to-face shared service area space 13. Face-to-back shared space Floor leveling Delivery access requirements14. L-shaped turn Turning radiusPassage or doorway a width Minimum passage B width Turning radius for printer separatedTurning radius for unseparated printer components Turning radius for printer separated and upended on dollyTurning radius for printer not separated 10. Turning radius for feeder/stacker module Modules Turning radius for inverter feeder/stacker module11. Printer specifications and power requirements Printer hardware specifications and requirements summaryStackers Operating Feeder/stackerTwo FeederSpace planning templates Page Page Page Page Page Grid Pattern Page Cable lengths Power cable lengthsPower cable Length System connectionsCable enter/exit location top view Cable locationsChannel attachments System connections Installation Planning Guide Installation process InstallationYour responsibilities Ongoing maintenance Defining the printer to the hostSoftware licensing Meter reading and reporting Routine maintenanceSupplies Paper and other throughput stocksSelecting paper Acceptable paper stocks and sizes Page Page Table A-3. Throughput data DP135 Paper width and throughput speed Lcds printing onlyTable A-1. Throughput data DP100 Table A-2. Throughput data DP115Table A-5. Throughput data DP180 Table A-4. Throughput data DP155Figure A-1 pitch mode paper sizes Paper size and pitch mode minimum and maximumFeed direction for standard paper sizes Figure A-2 pitch mode paper sizesFigure A-3. A4 / 210 by 297 mm paper feeding long edge feed Figure A-7. B4 / 250 by 353 mm paper feeding long edge feed Paper care Figure A-9. Storing paper correctly Carton Hours CentigradeDry ink Other suppliesCartridge tapes Fuser agentDeveloper DiskettesFonts Stacker containers and pallets optionalMicr Positioning and Dimension Gauge Micr toolsMicr comparator Description Part number Paper Consumable supplies tablesPaper and special stocks tables Table A-6. Printer stocks listDescription Part number Table A-6. Printer stocks list Labels Gummed TransparenciesCover stock Description Part number Tab stockStraight collated singles forward, top Down Reversed collated singles bottom upTable A-7. Carbonless stocks for the printer Waste bottle Complete supplies list for the printerTable A-8. Complete supplies list for the printer Part Items Expected yield Description Number Carton Dry inkOrdering supplies Page Page Table A-9. Supplies checklist Table A-9. Supplies checklist Xerox Customer Service Support Center Xerox support servicesXerox Printing Systems Customer Support Center U. S Xdss will also send you a Xerox Customer Documentation Xerox Documentation and Software Services U. SXerox Customer Documentation Catalog Customereducationservices/newCes.jspOperator training Xerox Customer EducationXerox Font Services Xerox support services Installation Planning Guide DocuPrint 100/115/135/155/180 EPS documentation Related publicationsNPS/IPS publications Filename Printing the customer documentationRelated publications Installation Planning Guide GLOSSARY-1 GlossaryComputer space equivalents are Multipliers areGLOSSARY-3 GLOSSARY-4 GLOSSARY-5 GLOSSARY-6 GLOSSARY-7 Micr GLOSSARY-9 PostScript Random Access Memory RAMResolution Portrait page orientationSpooling System administratorSoftware Software applicationGLOSSARY-12 INDEX-1 IndexMicr INDEX-3 INDEX-4
Related manuals
Manual 158 pages 14.95 Kb Manual 2 pages 14.6 Kb

155, 115, 135, 100 specifications

Xerox has long been a pioneer in the field of document technology, and its series of multifunction printers and copiers have consistently delivered quality and efficiency. Among the notable models are the Xerox 100, 135, 115, and 155, each designed to cater to specific business needs while incorporating advanced features and technologies.

The Xerox 100 series is well known for its compact design and is tailored for small to medium-sized businesses. It offers high-quality color printing, scanning, and copying, making it a versatile addition to any office environment. One of its standout features is the ability to handle a variety of media types, from plain paper to glossy sheets, enabling users to produce professional looking materials. With an intuitive touchscreen interface, users can easily navigate through functions, ensuring a streamlined workflow.

Moving up the ladder, the Xerox 135 series boasts enhanced productivity features, making it ideal for larger businesses or departments with higher volume print needs. It is equipped with an advanced finishing system, allowing users to create booklets, staple documents, and perform hole punching with ease. The 135 model integrates powerful cloud connectivity, facilitating remote printing and scanning directly from mobile devices, thereby boosting flexibility and efficiency.

The Xerox 115 model, on the other hand, emphasizes robustness and reliability. It is designed for environments that require fast processing speeds and high-volume output. Its security features, including secure print and automatic encryption, provide enhanced data protection for sensitive documents. Additionally, the 115 series incorporates smart workflow automation tools that reduce manual tasks, enabling staff to focus on more strategic activities.

Lastly, the Xerox 155 series is a powerful multifunction printer that combines high performance with advanced technology. It features a high-resolution color printing capability of up to 1200 x 2400 dpi, ensuring stunning image quality. The 155 is equipped with AI-driven features that optimize print workflows, reduce waste, and lower operational costs. An intuitive user interface offers custom shortcuts for frequent tasks, enhancing productivity and user satisfaction.

In summary, the Xerox 100, 135, 115, and 155 models cater to a wide array of business needs through their unique features and technologies. From compact designs for small offices to robust solutions for high-volume printing, these printers exemplify Xerox’s commitment to innovation and excellence in document management.