Installation

4.0Inspection

Inspect the UPS upon receipt. The packaging is recyclable; save it for reuse or dispose of it properly.

4.1Placement

Install the UPS in a protected area with adequate air flow and free of excessive dust. Do not operate the UPS where the temperature and humidity are beyond the specified limits.

4.2Connect Computer Interface (F6C425/F6C525/F6C625 models only) Belkin shutdown software and RS232 cable can be used with this UPS. If used, connect the interface cable to the 9 pin computer inter- face port on the back panel of the UPS and then connect to the seri- al port on your PC.

Note: Computer interface connection is optional. The UPS works properly without a computer interface connection.

4.3Connect to Utility

Connect the AC input power connector to utility power to power up the UPS.

4.4Charge the Battery

The UPS charges its battery whenever it is connected to the utility power. For best results, charge the battery for 4 hours prior

to initial use.

4.5Connect the Loads

Plug the loads into the output connectors on the rear of the UPS. To use the UPS as a master on/off switch, make sure all of the loads are switched on.

Caution: Never connect a laser printer or scanner to the UPS with other computer equipment. A laser printer or scanner periodically draws significantly more power when in use than when idle. This may overload the UPS.

Installation (continued)

4.6Connect the telephone/fax/modem lines (F6C425/F6C525/F6C625 models only)

Connect a single line telephone/fax/modem line into the surge pro- tected sockets on the back of the UPS. The RJ-45/RJ-11 modular sockets accept standard single line telephone connections. This con- nection will require another length of telephone cable (supplied).

Note: This connection is optional but highly suggested as phone/fax/modem lines often carry dangerous surges and spikes. The UPS works properly without a phone/fax/modem connection.

Caution: The telephone/fax/modem protection feature could be ren- dered inoperable if improperly installed. Make sure that the tele- phone line from the wall is plugged into the connector marked "IN", and the device to be protected (telephone/fax/modem) is plugged into the connector marked "OUT."

Caution: This surge protection device is for indoor use only. Never install telephone wiring during a lightning storm.

F6C425, F6C625, F6C525, F6C325 specifications

The Belkin F6C series, including the F6C425, F6C625, F6C325, and F6C525 models, represents a line of high-quality surge protectors designed to safeguard electronic devices against voltage spikes and surges. Each model in this series combines advanced technology with user-friendly features, making them ideal for both home and office use.

One of the standout features of the Belkin F6C series is its ability to protect against power surges. Each model is equipped with a high-capacity surge suppression technology that can absorb excess voltage and prevent damage to connected devices. This is particularly important in areas that experience frequent electrical storms or fluctuations in power supply.

The F6C series also offers multiple outlets, allowing users to connect several devices simultaneously. For instance, the F6C625 features an impressive 12 outlets, while the F6C525 and F6C425 provide 8 and 6 outlets respectively. This is particularly useful for powering up an array of gadgets, such as computers, printers, and gaming consoles, all from a single source. The F6C325, with its 4 outlets, is tailored for more compact setups.

In addition to surge protection, the Belkin F6C series incorporates safety features such as LED indicators that show protection status and alert users when the device is functioning properly. Some models, like the F6C625, include not only surge protection but also a built-in circuit breaker to prevent overloads. These safety mechanisms are crucial for ensuring long-term protection of valuable electronics.

Another key characteristic of the F6C series is its cord management capabilities. Each model is designed with a durable, long power cord that provides flexibility in placement without compromising safety. The cord is typically 6 to 12 feet long, giving users the ability to position the surge protector conveniently near their devices.

Furthermore, Belkin’s commitment to quality is evident in the construction of the F6C series. Each unit features a slim design that makes it suitable for use in tight spaces, such as behind furniture or office equipment. The robust housing is built to withstand daily use while also providing an aesthetically pleasing appearance.

In summary, the Belkin F6C425, F6C625, F6C325, and F6C525 surge protectors offer a combination of advanced surge protection technology, multiple outlet configurations, essential safety features, and a user-friendly design. These characteristics make them an excellent choice for individuals seeking reliable protection for their electronic devices in both residential and commercial settings.