Belkin F5D7630-4B, F5D7630-4A Installing the Hardware, Connecting And Configuring Your Router

Page 13

Step 1: Installing the Hardware

CONNECTING AND CONFIGURING YOUR ROUTER

•Set the Router’s firewall to work with specific applications (port forwarding).

•Set up security features such as client restrictions and MAC address filtering.

•Enable the DMZ feature for a single computer on your network.

•Change the Router’s internal password.

•Reset the Router.

•Reset the Router’s default settings.

•Update the Router’s firmware.

Step 1: Installing the Hardware

1.Power down your equipment.

2.Connect each PC to one of the ports on the rear of the Router labeled LAN by using a RJ45 networking cable.

LAN Ports

3.Connect the telephone cable from the wall jack providing ADSL service to the ADSL port on your Router.

Note: When inserting an ADSL RJ11 plug, be sure the tab on the plug clicks into position to ensure that it is properly seated.

4.Connect the power adapter to the Router.

5.After the Router is turned on, the Router’s Power light should be on.

11

Image 13

Contents User Manual ADSL Modem with Built-In 802.11g Wireless RouterF5D7630-4A F5D7630-4B TABLE OF CONTENTS INTRODUCTION Key Features Integrated 802.11g Wireless Access PointOVERVIEW Works with Both PCs and Mac ComputersSPI Firewall Integrated 10/100 4-Port SwitchMAC Address Filtering Applications and AdvantagesSystem Requirements Package ContentsGermany excluded Provided by local ISP Wireless Network LED Power LED PWRKNOWING YOUR ROUTER Front PanelLAN Port-Status LEDs Reset ButtonRear Panel LAN Portsb. Restoring the Factory Defaults a. Resetting the RouterPower Jack ADSL PortPLACEMENT OF YOUR ROUTER ISP Settings CONNECTING AND CONFIGURING YOUR ROUTERPhone Line Configuration Installing a Full-Rate ConnectionInstalling with a Splitter Installing a Splitterless Connection Installing without a Splitter Configuring the RouterAttach to your Network Using Ethernet Cabling Step 1 Installing the Hardware LAN Port Status LEDs Step 3 Configuring the Router Using the Web-Based User InterfaceLogging out of the Router Logging into the Router2. Setting your ISP Connection Type to PPPoE or PPPoA Setup WizardNAVIGATING THE WEB BROWSER INTERFACE 1. Internet Sharing4. Setting your Connection Type to Multiple Protocol over ATM Mode 3. Setting your Connection Type to Disable Internet SharingDefault Gateway - Enter a default gateway IP address. If the Wireless ADSL Modem Router cannot find the destination address within its local network, it will forward the packets to the Default Gateway. Assigned by your ISP 4. Login/Logout Button 3. Internet Status IndicatorUNDERSTANDING THE WEB-BASED USER INTERFACE 1. Quick-Navigation Links7. Features 6. LAN Settings8. Internet Settings 5. Help Button1. LAN Settings Changing LAN Settings2. Subnet Mask 1. IP Address3. DHCP Server 4. IP PoolDHCP Client List 6. Local Domain Name2. Internet WAN Connection Type Setting your ISP Connection Type to PPPoE or PPPoAa b c d e f g h i j a. Username - Enter the ISP assigned user name. Assigned by your ISP Setting your ISP Connection Type to Multiple Protocol over ATM Setting your ISP Connection Type to Disable Internet Sharinga b c d e 3. Wireless DNS Domain Name Server SettingsChanging the Wireless Channel Channel and SSIDChanging the Wireless Network Name SSID Note This advanced feature should be employed by advanced users only Using the ESSID Broadcast FeatureUsing the Wireless Mode Switch Setting WPA Security Changing the Wireless Security SettingsEncryption/Security g NitroSetting WPA with server Settings Setting WPA-PSK no serverSetting WEP Encryption AF 0F 4B C3 D4 = 64-bit key Using a Hexadecimal KeyC3 03 0F AF 0F 4B B2 C3 D4 4B C3 D4 E7 = 128-bit key IP Spoofing Land Attack Ping of Death PoD Denial of Service DoS 4. FirewallIP with zero length Smurf Attack TCP Null Scan SYN flood UDP flooding Tear Drop Attack ICMP defect RIP defect Fragment floodingChoosing an Application Application Gateways SettingsVirtual Servers Entering Settings into the Virtual ServerClient IP Filters Access Control Schedule Rule URL BlockingFollow these steps to add a schedule 1. Click “Add Schedule Rule” DMZ Demilitarized Zone Restart Router UtilitiesRestore Factory Defaults Restarting the Router to Restore Normal OperationSaving/Backup Current Settings The configuration is now saved Restore Previous Settings2. Then, click “Restore” System Settings Firmware UpdateUpdating the Router’s Firmware Changing the Login Time-Out Setting Setting or Changing the Administrator PasswordSetting the Time and Time Zone Enabling Remote Management Enabling/Disabling UPnP Manually Configuring Network Settings in Mac OS up to MANUALLY CONFIGURING NETWORK SETTINGSManually Configuring Network Settings in Mac OS 3. Select “Built-in Ethernet” 2 next to “Show” in the Network menu Manually Configuring Network Settings in Windows 2000, NT, or XP Manually Configuring Network Settings in Windows 98 or Me Microsoft Internet Explorer 4.0 or Higher Recommended Web Browser SettingsNetscape Navigator 4.0 or Higher IP address GLOSSARYSubnet Mask PPPoE Routing Mode, for multiple PCsDisconnect after PPPoA Routing Mode, for multiple PCsChannel and SSID Encryption ESSID BroadcastApplication Gateways Client IP filters Administrator Password Remote Management Time and Time ZoneUPnP Problem TROUBLESHOOTINGPossible Cause/Solution connect to the Router My wireless PC cannotFCC Statement DECLARATION OF CONFORMITY WITH FCC RULES FOR INFORMATIONELECTROMAGNETIC COMPATIBILITY ModificationsEurope-European Union Notice Canada-Industry Canada ICBelkin Corporation Limited Lifetime Product Warranty Belkin Corporation P74426ukBelkin Components B.V Belkin Tech Support