Belkin F5D7630-4B Information, FCC Statement DECLARATION OF CONFORMITY WITH FCC RULES FOR

Page 65

INFORMATION

INFORMATION

FCC Statement

DECLARATION OF CONFORMITY WITH FCC RULES FOR

ELECTROMAGNETIC COMPATIBILITY

We, Belkin Corporation, of 501 West Walnut Street, Compton, CA 90220, declare under our sole responsibility that the product,

F5D7630-4

to which this declaration relates,

complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Caution: Exposure to Radio Frequency Radiation.

The radiated output power of this device is far below the FCC radio frequency exposure limits. Nevertheless, the device shall be used in such manner that the potential for human contact normal operation is minimized.

When connecting an external antenna to the device, the antenna shall be placed in such a manner to minimize the potential for human contact during normal operation. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation.

Federal Communications Commission Notice

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the distance between the equipment and the receiver.

•Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

Modifications

The FCC requires the user to be notified that any changes or modifications to this device that are not expressly approved by Belkin Corporation may void the users authority to operate the equipment.

63

Image 65

Contents F5D7630-4A F5D7630-4B ADSL Modem with Built-In 802.11g Wireless RouterUser Manual TABLE OF CONTENTS INTRODUCTION Key Features Integrated 802.11g Wireless Access PointOVERVIEW Works with Both PCs and Mac ComputersSPI Firewall Integrated 10/100 4-Port SwitchMAC Address Filtering Applications and AdvantagesGermany excluded Provided by local ISP Package ContentsSystem Requirements Wireless Network LED Power LED PWRKNOWING YOUR ROUTER Front PanelLAN Port-Status LEDs Reset ButtonRear Panel LAN Portsb. Restoring the Factory Defaults a. Resetting the RouterPower Jack ADSL PortPLACEMENT OF YOUR ROUTER ISP Settings CONNECTING AND CONFIGURING YOUR ROUTERPhone Line Configuration Installing a Full-Rate ConnectionInstalling with a Splitter Installing a Splitterless Connection Attach to your Network Using Ethernet Cabling Configuring the RouterInstalling without a Splitter Step 1 Installing the Hardware LAN Port Status LEDs Step 3 Configuring the Router Using the Web-Based User InterfaceLogging out of the Router Logging into the Router2. Setting your ISP Connection Type to PPPoE or PPPoA Setup WizardNAVIGATING THE WEB BROWSER INTERFACE 1. Internet Sharing4. Setting your Connection Type to Multiple Protocol over ATM Mode 3. Setting your Connection Type to Disable Internet SharingDefault Gateway - Enter a default gateway IP address. If the Wireless ADSL Modem Router cannot find the destination address within its local network, it will forward the packets to the Default Gateway. Assigned by your ISP 4. Login/Logout Button 3. Internet Status IndicatorUNDERSTANDING THE WEB-BASED USER INTERFACE 1. Quick-Navigation Links7. Features 6. LAN Settings8. Internet Settings 5. Help Button1. LAN Settings Changing LAN Settings2. Subnet Mask 1. IP Address3. DHCP Server 4. IP PoolDHCP Client List 6. Local Domain Name2. Internet WAN a b c d e f g h i j Setting your ISP Connection Type to PPPoE or PPPoAConnection Type a. Username - Enter the ISP assigned user name. Assigned by your ISP a b c d e Setting your ISP Connection Type to Disable Internet SharingSetting your ISP Connection Type to Multiple Protocol over ATM 3. Wireless DNS Domain Name Server SettingsChanging the Wireless Channel Channel and SSIDChanging the Wireless Network Name SSID Using the Wireless Mode Switch Using the ESSID Broadcast FeatureNote This advanced feature should be employed by advanced users only Setting WPA Security Changing the Wireless Security SettingsEncryption/Security g NitroSetting WPA with server Settings Setting WPA-PSK no serverSetting WEP Encryption C3 03 0F AF 0F 4B B2 C3 D4 4B C3 D4 E7 = 128-bit key Using a Hexadecimal KeyAF 0F 4B C3 D4 = 64-bit key IP Spoofing Land Attack Ping of Death PoD Denial of Service DoS 4. FirewallIP with zero length Smurf Attack TCP Null Scan SYN flood UDP flooding Tear Drop Attack ICMP defect RIP defect Fragment floodingChoosing an Application Application Gateways SettingsClient IP Filters Entering Settings into the Virtual ServerVirtual Servers Access Control Schedule Rule URL BlockingFollow these steps to add a schedule 1. Click “Add Schedule Rule” DMZ Demilitarized Zone Restart Router UtilitiesRestore Factory Defaults Restarting the Router to Restore Normal OperationSaving/Backup Current Settings 2. Then, click “Restore” Restore Previous SettingsThe configuration is now saved Updating the Router’s Firmware Firmware UpdateSystem Settings Setting the Time and Time Zone Setting or Changing the Administrator PasswordChanging the Login Time-Out Setting Enabling Remote Management Enabling/Disabling UPnP Manually Configuring Network Settings in Mac OS up to MANUALLY CONFIGURING NETWORK SETTINGSManually Configuring Network Settings in Mac OS 3. Select “Built-in Ethernet” 2 next to “Show” in the Network menu Manually Configuring Network Settings in Windows 2000, NT, or XP Manually Configuring Network Settings in Windows 98 or Me Microsoft Internet Explorer 4.0 or Higher Recommended Web Browser SettingsNetscape Navigator 4.0 or Higher IP address GLOSSARYSubnet Mask PPPoE Routing Mode, for multiple PCsChannel and SSID PPPoA Routing Mode, for multiple PCsDisconnect after Application Gateways ESSID BroadcastEncryption Client IP filters Administrator Password UPnP Time and Time ZoneRemote Management Possible Cause/Solution TROUBLESHOOTINGProblem connect to the Router My wireless PC cannotFCC Statement DECLARATION OF CONFORMITY WITH FCC RULES FOR INFORMATIONELECTROMAGNETIC COMPATIBILITY ModificationsEurope-European Union Notice Canada-Industry Canada ICBelkin Corporation Limited Lifetime Product Warranty Belkin Corporation P74426ukBelkin Components B.V Belkin Tech Support