Belkin F5D7630-4A Configuring the Router Using the Web-Based User Interface, LAN Port Status LEDs

Page 14

LAN Port

CONNECTING AND CONFIGURING YOUR ROUTER

6.Turn on the rest of your computers. After your computers boot up, a LAN link light (on the front of the Router) will be on for each port to which a wired computer is connected. These lights are your means to verify that your computers are connected.

LAN Port

Status LEDs

Step 2: Set your Computer’s Network Settings to Work with a DHCP Server

Configure the TCP/IP settings on your computers to obtain an IP address automatically. The Router will assign each computer an IP address in the range of 192.168.2.x. In most cases, your computer is programmed to automatically obtain your IP address when you turn it on. If your computer is not set to work with a DHCP server, then see the section in this manual called “Manually Configuring Network Settings” for directions.

Step 3: Configuring the Router Using the Web-Based User Interface

Using your Internet browser, you can access the Router’s Web-Based User Interface. In your browser, type “192.168.2.1” (do not type in anything else such as “http://” or “www”). Then press the “Enter” key.

12

Image 14

Contents F5D7630-4A F5D7630-4B ADSL Modem with Built-In 802.11g Wireless RouterUser Manual TABLE OF CONTENTS OVERVIEW Key Features Integrated 802.11g Wireless Access PointINTRODUCTION Works with Both PCs and Mac ComputersMAC Address Filtering Integrated 10/100 4-Port SwitchSPI Firewall Applications and AdvantagesGermany excluded Provided by local ISP Package ContentsSystem Requirements KNOWING YOUR ROUTER Power LED PWRWireless Network LED Front PanelRear Panel Reset ButtonLAN Port-Status LEDs LAN PortsPower Jack a. Resetting the Routerb. Restoring the Factory Defaults ADSL PortPLACEMENT OF YOUR ROUTER Phone Line Configuration CONNECTING AND CONFIGURING YOUR ROUTERISP Settings Installing a Full-Rate ConnectionInstalling with a Splitter Installing a Splitterless Connection Attach to your Network Using Ethernet Cabling Configuring the RouterInstalling without a Splitter Step 1 Installing the Hardware Step 3 Configuring the Router Using the Web-Based User Interface LAN Port Status LEDsLogging into the Router Logging out of the RouterNAVIGATING THE WEB BROWSER INTERFACE Setup Wizard2. Setting your ISP Connection Type to PPPoE or PPPoA 1. Internet Sharing3. Setting your Connection Type to Disable Internet Sharing 4. Setting your Connection Type to Multiple Protocol over ATM ModeDefault Gateway - Enter a default gateway IP address. If the Wireless ADSL Modem Router cannot find the destination address within its local network, it will forward the packets to the Default Gateway. Assigned by your ISP UNDERSTANDING THE WEB-BASED USER INTERFACE 3. Internet Status Indicator4. Login/Logout Button 1. Quick-Navigation Links8. Internet Settings 6. LAN Settings7. Features 5. Help ButtonChanging LAN Settings 1. LAN Settings3. DHCP Server 1. IP Address2. Subnet Mask 4. IP Pool6. Local Domain Name DHCP Client List2. Internet WAN a b c d e f g h i j Setting your ISP Connection Type to PPPoE or PPPoAConnection Type a. Username - Enter the ISP assigned user name. Assigned by your ISP a b c d e Setting your ISP Connection Type to Disable Internet SharingSetting your ISP Connection Type to Multiple Protocol over ATM Changing the Wireless Channel DNS Domain Name Server Settings3. Wireless Channel and SSIDChanging the Wireless Network Name SSID Using the Wireless Mode Switch Using the ESSID Broadcast FeatureNote This advanced feature should be employed by advanced users only Encryption/Security Changing the Wireless Security SettingsSetting WPA Security g NitroSetting WPA-PSK no server Setting WPA with server SettingsSetting WEP Encryption C3 03 0F AF 0F 4B B2 C3 D4 4B C3 D4 E7 = 128-bit key Using a Hexadecimal KeyAF 0F 4B C3 D4 = 64-bit key IP with zero length Smurf Attack TCP Null Scan SYN flood UDP flooding 4. FirewallIP Spoofing Land Attack Ping of Death PoD Denial of Service DoS Tear Drop Attack ICMP defect RIP defect Fragment floodingApplication Gateways Settings Choosing an ApplicationClient IP Filters Entering Settings into the Virtual ServerVirtual Servers Access Control URL Blocking Schedule RuleFollow these steps to add a schedule 1. Click “Add Schedule Rule” DMZ Demilitarized Zone Utilities Restart RouterRestarting the Router to Restore Normal Operation Restore Factory DefaultsSaving/Backup Current Settings 2. Then, click “Restore” Restore Previous SettingsThe configuration is now saved Updating the Router’s Firmware Firmware UpdateSystem Settings Setting the Time and Time Zone Setting or Changing the Administrator PasswordChanging the Login Time-Out Setting Enabling Remote Management Enabling/Disabling UPnP MANUALLY CONFIGURING NETWORK SETTINGS Manually Configuring Network Settings in Mac OS up toManually Configuring Network Settings in Mac OS 3. Select “Built-in Ethernet” 2 next to “Show” in the Network menu Manually Configuring Network Settings in Windows 2000, NT, or XP Manually Configuring Network Settings in Windows 98 or Me Recommended Web Browser Settings Microsoft Internet Explorer 4.0 or HigherNetscape Navigator 4.0 or Higher Subnet Mask GLOSSARYIP address PPPoE Routing Mode, for multiple PCsChannel and SSID PPPoA Routing Mode, for multiple PCsDisconnect after Application Gateways ESSID BroadcastEncryption Client IP filters Administrator Password UPnP Time and Time ZoneRemote Management Possible Cause/Solution TROUBLESHOOTINGProblem My wireless PC cannot connect to the RouterELECTROMAGNETIC COMPATIBILITY INFORMATIONFCC Statement DECLARATION OF CONFORMITY WITH FCC RULES FOR ModificationsCanada-Industry Canada IC Europe-European Union NoticeBelkin Corporation Limited Lifetime Product Warranty Belkin Components B.V P74426ukBelkin Corporation Belkin Tech Support