IBM 4364, 4365 manual Connecting the cables, Updating the server configuration

Page 33

Connecting the cables

The following illustrations show the locations of the input and output connectors on the front and rear of the server.

Front

USB 1 connector

USB 2 connector

Rear

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Mouse connector

 

 

 

 

 

Power-cord connector

 

 

Keyboard connector

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Systems-management

USB 3 connector

Serial connector

connector

USB 4 connector

Video connector

 

 

 

Ethernet 2 connector

 

 

Ethernet 1 connector

You must turn off the server before you connect or disconnect cables.

See the documentation that comes with any external devices for additional cabling instructions. It might be easier for you to route cables before you connect the devices to the server.

Cable identifiers are printed on the cables that come with the server and devices. Use these identifiers to connect the cables to the correct connectors.

If the server comes with an installed operating system, see the documentation that comes with the operating system for additional cabling instructions.

There is one keyboard connector on the back of the server. Use this connector to connect the server to a keyboard or optional console switch. You can also connect a USB keyboard to the server by using one of the USB connectors. After you install a USB keyboard, you might have to use the Configuration/Setup Utility program to enable keyboardless operation and prevent the POST error message 301 from being displayed during startup. For information about how to connect a USB keyboard to the server, see the documentation that comes with the keyboard. If the server cables and connector panel have color-coded connectors, match the color of each cable end with the color of the connector. For example, match a blue cable end to a blue connector on the panel, a red cable end to a red connector, and so on.

Updating the server configuration

When you start the server for the first time after you add or remove an internal optional device or external SAS device, you might receive a message that the configuration has changed. The Configuration/Setup Utility program starts automatically so that you can save the new configuration settings. For more information, see Chapter 4, “Configuring the server,” on page 25.

Chapter 2. Installing optional devices 19

Image 33
Contents Installation Guide Server Support Installation Guide Page Contents Iv IBM System x3250 Types 4364 and 4365 Installation Guide Safety Vi IBM System x3250 Types 4364 and 4365 Installation Guide To Connect To Disconnect Do not Safety Statement Safety Xii IBM System x3250 Types 4364 and 4365 Installation Guide Introduction Using the Documentation Browser \win32.bat Microprocessor Features and specificationsDimm Major components of the serverSystem-board optional-device connectors Installation guidelines Installing optional devicesHandling static-sensitive devices System reliability guidelinesRemoving the cover Installing a memory moduleIBM System x3250 Types 4364 and 4365 Installation Guide Installing a simple-swap Serial ATA hard disk drive Installing a hard disk driveInstalling a hot-swap hard disk drive Installing an adapter Page Riser-card assembly IBM System x3250 Types 4364 and 4365 Installation Guide Installing a Remote Supervisor Adapter II SlimLine Installing the cover Completing the installationUpdating the server configuration Connecting the cablesIBM System x3250 Types 4364 and 4365 Installation Guide Front view Server controls, LEDs, and powerRear view Server power features Turning on the serverTurning off the server IBM System x3250 Types 4364 and 4365 Installation Guide Using the ServerGuide Setup and Installation CD Configuring the serverUsing the LSI Logic Configuration Utility program Using the Configuration/Setup Utility programUsing the baseboard management controller IBM System x3250 Types 4364 and 4365 Installation Guide Solving problems Diagnostic tools overviewPost beep codes System x Documentation CD Post error codesDefault Settings, and save Abbreviated list of Post error codes Determination and Service Abbreviated list of Post error codes Only Replace Abbreviated list of Post error codes CD or DVD drive problems Troubleshooting tablesHard disk drive problems General problemsKeyboard, mouse, or pointing-device problems Intermittent problemsProblem Determination and Service Guide Memory problemsMonitor problems Microprocessor problemsService Guide Solving problems Optional-device problems Power problems ServerGuide problems Serial port problemsSoftware problems Video problems Universal Serial Bus USB port problemsUsing the documentation Appendix A. Getting help and technical assistanceBefore you call Software service and support Hardware service and support IBM Taiwan product serviceGetting help and information from the World Wide Web Trademarks Appendix B. NoticesImportant notes Product recycling and disposal For the European Union Battery return programIndustry Canada Class a emission compliance statement European Union EMC Directive conformance statement SAS Sata IndexSee SAS ServerGuide LSI Logic Configuration Utility program IBM System x3250 Types 4364 and 4365 Installation Guide Page Part Number 42C5004

4364, 4365 specifications

The IBM 4365 and 4364 are significant models in IBM’s lineup of mainframe computers, designed primarily for large organizations requiring robust processing capabilities. These models emerged during the late 1980s and early 1990s, serving to enhance the performance and versatility of business computing environments.

The IBM 4365, launched in 1985, is known for its sophisticated architecture and large processing power, capable of managing substantial transaction volumes. It features the advanced Multiple Virtual Storage (MVS) operating system, which allows for efficient processing and management of numerous tasks simultaneously. The MVS system contributes to high reliability and availability, factors paramount for businesses that rely on uninterrupted service.

One of the standout characteristics of the IBM 4365 is its ability to scale. Users could configure the system with multiple processors, allowing it to handle increasing workloads effectively. This scalability is made possible through its use of IBM's proprietary technology, which optimizes resource allocation to improve efficiency. The system could support an impressive number of users, making it ideal for large enterprises.

In contrast, the IBM 4364, released slightly later, is a more modest version aimed at smaller organizations but still renowned for its reliable performance. It too operates the MVS operating system, but its configurations are tailored for less intensive processing needs. It is designed with cost-effectiveness in mind, making it suitable for businesses that require robust computing without the extensive capabilities of larger systems.

Both models benefit from IBM's robust security features, ensuring data protection and compliance with industry standards. Additionally, they offer significant storage options, utilizing IBM's innovative storage technologies to retain vast amounts of data efficiently.

Among the key technologies that defined these mainframes were the use of advanced input/output capabilities and compatibility with a broad range of peripheral devices. This integration allowed organizations to enhance productivity while maintaining seamless operations across various applications.

Overall, the IBM 4365 and 4364 exemplify the evolution of mainframe technology during their era, offering remarkable processing power, superior reliability, and scalability while paving the way for future innovations in enterprise computing. Their legacy remains influential in shaping the landscape of business technology today, as organizations continue to rely on mainframe processing for critical operations.