SATO CX208/212 manual Printer configuration until a new Base Reference Point

Page 24

CX208/212 Programming Guide

Special Notes	1.	Use of this command will set the Vertical/Horizontal Offset setting
		of the printer configuration until a new Base Reference Point
		command is issued.
	2.	This command may be used more than once in a print job.
	3.	An alternative to using this command is to make changes to your
		current Horizontal and Vertical Print Position commands.
		Example:
		Let’s say the current base reference point is H=1, V=1 and you
		wish to move all the fields on your label downward vertically by
		150 dots. You could either (1) add the Base Reference Point
		command or (2) change all the vertical position commands by an
		additional 150 dots.
	4.	For a more detailed example of the Base Reference Point
		command, see “Print Area” in this section.
	5.	The CX208/212 printers will not “wrap” (i.e. if any part of a
		character or image extends beyond the last print dot position, it
		will disappear and not be visible on any part of the label).
	6.	The allowable ranges for the fields are:

				CX208		CX212


	Horizontal			0 to 0832		0 to 1230
	aaaa

	Vertical			0 to 1424		0 to 2100
	bbbb			0 to 4060		0 to 3780

Page 20

PN 9001092 Rev. A

SATO CX208/212 Printers

Image 24

Contents CX208/212 Page Table of Contents Sato CX208/212 Printers PN 9001092 Rev. a Introduction Sato Programming LanguageUsing Basic Selecting Protocol Control CodesPrinting with the Parallel Port Printing with the RS232 PortPrint Area CX208/212 Programming GuidePage Rotated Fields Command Default Settings Printer ConfigurationLabel Sensing ESCAESCCP1ESCCI2ESCCAESCZ Command Code page Reference Bar Codes MSIA01597 Input to PrinterPrinter Output CX208/212 Programming Guide Special Notes Command Structure ESCBWaabbb Bar Codes, ExpansionPrinter Output Special Notes Command Structure ESCBTabbccddee Bar Codes, Variable RatioThis command must be immediately followed by the Escbw Command Structure ESCA3H-aaaaVbbbb Base Reference PointPrinter configuration until a new Base Reference Point Command Structure Store Command ESCTabcc Characters, Custom-DesignedESCK1H903F Printer InputWhen printing the custom character using the Esck Recall Character Expansion This command will expand the following fonts Command Structure Escpr Character, Fixed SpacingCommand Structure ESCPaa Character PitchThis command is affected by the Escl Character Expansion Command Structure Escps Character, Proportional SpacingCommand Structure Clear Print Jobs & MemorySpecial Note Command Structure None Continuous Forms PrintingCommand Structure ESCWDHaaaaVbbbbXccccYdddd Copy Image AreaExample ESCWDH0100V0050X0600Y0400 Horizontal 0001 Aaaa Cutter Command Command Structure ESC~aaaa or ESCNULaaaaFonts U, S, M, OA, OB, XU, XS & XM EscoaCharacters may be enlarged through the use of the Character Fonts WB, WL, XB & XL ESCWB1123456Characters may be enlarged through the use of the Escl Form Feed Command Structure ESC Form Overlay, RecallForm Overlay, Store Command Structure ESCGabbbcccdata Graphics, CustomCustom graphic cannot be enlarged by the Escl Character Command Structure ESCGPaaaaa,data Graphics, PCXCommand Structure Escj Journal PrintCommand Structure Line ESCFWaabcccc Lines and BoxesESCFWaabbVccccHdddd CX208/212 Programming Guide Field ranges are Line Feed Command Structure ESCA1aaaabbbb Media SizeOff-Line/Pause Command Structure ESCBPn...n PostnetCommand Structure ESC#Ea Print DarknessPrint Length, Expanded MaximumPrint length, or until the printer is repowered Print Position ESCQ2ESCZAH0025100 0150ESCL0303ESCMSATOPrint position of a field is affected by both the Rotate Command Structure ESCQaaaaaa Print QuantityCommand Structure ESCCSa Print SpeedRepeat Label EsccCommand Structure ESC0 ESCzero Replace Data Partial EditFewer characters than the old data, then the characters not Command Structure ESCaaaa,bbbb Reverse ImageESC100,50 CX208 CX212 Command Structure ESC%a Rotate, Fixed Base Reference PointSame data stream ESCAQ1ESCZNR Rotate, Moving Base Reference PointThis command is provided for compatibility with other Sato Command Structure ESCFaaaabcccc,dd,ee Sequential NumberingESCF001-001,04,03 Value specified for Print Quantity should be equal to Start/Stop Label Expanded Memory Option Commands Command Structure ESC*a,bb Expanded Memory Function Clear Expanded MemoryCommand Structure ESCBJT,aa,bb,cc,dd,ee,ffff,gg..g Expanded Memory Function Fonts, TrueType RecallExample ESCBJT,11,02,02,01,00,0004,SATO Expanded Memory Function Fonts, TrueType Store Command Structure Command Function Printer Input ESCGRaaa Expanded Memory Function Graphics, Custom RecallCommand Structure ESCGIabbbcccddddata Expanded Memory Function Graphics, Custom StoreESCGIHaaabbb002DATA Escz Command Structure ESCPYaaa Expanded Memory Function Graphics, PCX RecallExpanded Memory Function Graphics, PCX Store ESCPI001,32000,dataESCZCC2ESCA Expanded Memory Function InitializeESCZACC1 Expanded Memory Function Area SelectBJS Expanded Memory Function StatusTwo-Dimensional Symbols Two-Dimensional Bar Codes Maxicode Example ESCBV1,2,3,123456789,222,333,MESSAGEESCPlease refer to UPS Publication Guide to Bar Coding with UPS Two-Dimensional Bar Codes Command Structure Command Function Printer InputBK0304400000021 Values 00Hthru 1FHcan be specified as print data Configuration Commands Command Structure ESCCFa Auto-CalibrateBackfeed Enable Command Structure ESCCEaCalibrate Sensor Custom Protocol Command Codes Download Command Structure ESCLD,a,b,c,d,e,f,g,h,iCommand Function Printer Input Printer Output ESCLD,,,%,#,&,*,~,0,0Resulting Command Code Command Structure ESCCBabb Label Tear-OffPrint Darkness Range Adjustment Print Test Label ESC AzctSet Print Mode Command Structure ESCCPaCommand Structure ESCCRaaaaa,b,c,d Set RS232 ParametersCommand Structure ESCCIa Set Sensor TypeESC AZCI2 Enable Options ESC CL1Mode