SATO CX208/212 manual Values 00Hthru 1FHcan be specified as print data

Page 90

CX208/212 Programming Guide

2.If the product of the values entered for “dd” and “ee” are not equal to or less than the value of “fff” (i.e.,“ffff” is greater that “dd” x “ee”), an error will occur and the symbol will not be printed. It is recommended that these values each be set to “000” and the printer be allowed to automatically calculate the optimum values.

3.The values for “dd” and “ee” need to be made larger if the security level is increased.

4.The maximum data length is 2700 characters, but may be less depending upon:

-the minimum module dimension (“aa”)

-the security level specified by “c”.

-the number of data characters

5.The Reference Point of the PDF417 symbol is the upper-left corner.

6.The <ESC>F Sequential Numbering command cannot be used with this command.

7.The <ESC>E Line Feed command cannot be used with this command.

8.The Macro and Truncated PDF417 symbols are not supported.

9.The values 00Hthru 1FHcan be specified as print data.

10.This command can be stored in a format.

11.The <ESC>R Rotate command can be used.

12.The print height of the symbol will vary depending upon the data specified; numeric only, alpha only or alphanumeric.

Page 86

PN 9001092 Rev. A

SATO CX208/212 Printers

Image 90

Contents CX208/212 Page Table of Contents Sato CX208/212 Printers PN 9001092 Rev. a Introduction Sato Programming LanguageUsing Basic Selecting Protocol Control CodesPrinting with the Parallel Port Printing with the RS232 PortPrint Area CX208/212 Programming GuidePage Rotated Fields Command Default Settings Printer ConfigurationLabel Sensing ESCAESCCP1ESCCI2ESCCAESCZ Command Code page Reference Bar Codes MSIA01597 Input to PrinterPrinter Output CX208/212 Programming Guide Special Notes Command Structure ESCBWaabbb Bar Codes, ExpansionPrinter Output Special Notes Command Structure ESCBTabbccddee Bar Codes, Variable RatioThis command must be immediately followed by the Escbw Command Structure ESCA3H-aaaaVbbbb Base Reference PointPrinter configuration until a new Base Reference Point ESCK1H903F Command Structure Store Command ESCTabccCharacters, Custom-Designed Printer InputWhen printing the custom character using the Esck Recall Character Expansion This command will expand the following fonts Command Structure Escpr Character, Fixed SpacingCommand Structure ESCPaa Character PitchThis command is affected by the Escl Character Expansion Command Structure Escps Character, Proportional SpacingCommand Structure Clear Print Jobs & MemorySpecial Note Command Structure None Continuous Forms PrintingCommand Structure ESCWDHaaaaVbbbbXccccYdddd Copy Image AreaExample ESCWDH0100V0050X0600Y0400 Horizontal 0001 Aaaa Cutter Command Command Structure ESC~aaaa or ESCNULaaaaFonts U, S, M, OA, OB, XU, XS & XM EscoaCharacters may be enlarged through the use of the Character Fonts WB, WL, XB & XL ESCWB1123456Characters may be enlarged through the use of the Escl Form Feed Command Structure ESC Form Overlay, RecallForm Overlay, Store Command Structure ESCGabbbcccdata Graphics, CustomCustom graphic cannot be enlarged by the Escl Character Command Structure ESCGPaaaaa,data Graphics, PCXCommand Structure Escj Journal PrintCommand Structure Line ESCFWaabcccc Lines and BoxesESCFWaabbVccccHdddd CX208/212 Programming Guide Field ranges are Line Feed Command Structure ESCA1aaaabbbb Media SizeOff-Line/Pause Command Structure ESCBPn...n PostnetCommand Structure ESC#Ea Print DarknessPrint Length, Expanded MaximumPrint length, or until the printer is repowered Print Position ESCQ2ESCZAH0025100 0150ESCL0303ESCMSATOPrint position of a field is affected by both the Rotate Command Structure ESCQaaaaaa Print QuantityCommand Structure ESCCSa Print SpeedRepeat Label EsccCommand Structure ESC0 ESCzero Replace Data Partial EditFewer characters than the old data, then the characters not Command Structure ESCaaaa,bbbb Reverse ImageESC100,50 CX208 CX212 Command Structure ESC%a Rotate, Fixed Base Reference PointSame data stream ESCAQ1ESCZNR Rotate, Moving Base Reference PointThis command is provided for compatibility with other Sato Command Structure ESCFaaaabcccc,dd,ee Sequential NumberingESCF001-001,04,03 Value specified for Print Quantity should be equal to Start/Stop Label Expanded Memory Option Commands Command Structure ESC*a,bb Expanded Memory Function Clear Expanded MemoryCommand Structure ESCBJT,aa,bb,cc,dd,ee,ffff,gg..g Expanded Memory Function Fonts, TrueType RecallExample ESCBJT,11,02,02,01,00,0004,SATO Expanded Memory Function Fonts, TrueType Store Command Structure Command Function Printer Input ESCGRaaa Expanded Memory Function Graphics, Custom RecallCommand Structure ESCGIabbbcccddddata Expanded Memory Function Graphics, Custom StoreESCGIHaaabbb002DATA Escz Command Structure ESCPYaaa Expanded Memory Function Graphics, PCX RecallExpanded Memory Function Graphics, PCX Store ESCPI001,32000,dataESCZCC2ESCA Expanded Memory Function InitializeESCZACC1 Expanded Memory Function Area SelectBJS Expanded Memory Function StatusTwo-Dimensional Symbols Two-Dimensional Bar Codes Maxicode Example ESCBV1,2,3,123456789,222,333,MESSAGEESCPlease refer to UPS Publication Guide to Bar Coding with UPS Two-Dimensional Bar Codes Command Structure Command Function Printer InputBK0304400000021 Values 00Hthru 1FHcan be specified as print data Configuration Commands Command Structure ESCCFa Auto-CalibrateBackfeed Enable Command Structure ESCCEaCalibrate Sensor Command Function Printer Input Printer Output Custom Protocol Command Codes DownloadCommand Structure ESCLD,a,b,c,d,e,f,g,h,i ESCLD,,,%,#,&,*,~,0,0Resulting Command Code Command Structure ESCCBabb Label Tear-OffPrint Darkness Range Adjustment Print Test Label ESC AzctSet Print Mode Command Structure ESCCPaCommand Structure ESCCRaaaaa,b,c,d Set RS232 ParametersCommand Structure ESCCIa Set Sensor TypeESC AZCI2 Enable Options ESC CL1Mode