Star Micronics TSP400Z Series user manual English

Page 16

ENGLISH

1)Make sure the printer is turned off.

2)Remove the ROM cover located beneath the paper-roll holding area.

3)Hold down the FEED and ON LINE switches while switching on the power, and continue to hold them down until you hear a triple beep. (This will take about five seconds.) When you hear the triple beep, release the buttons to enter the sensor-adjustment mode.

a)Reflective Sensor

•Insert a non-black piece of paper into the mechanism’s sensor area.

•Rotate the main PCB’s sensor adjustment knob (VR4) to the point where the HEAD UP indicator comes on.

b)Paper-Out Sensor

•Insert a non-black piece of paper into the mechanism’s sensor area.

•Rotate the main PCB’s sensor adjustment knob (VR3) to the point where the NO PAPER indicator comes on.

c)Transmissive Sensor

•Insert the backing portion of a label sheet into the mechanism’s transmissive sensor area. (Insert the backing only, not the label itself.)

•Adjust the main PCB’s coarse (VR1) and fine (VR2) adjustment knobs to the point where the ERROR indicator comes on.

NOTE: When inserting paper, be sure to lower the head so that it is close to its normal fixed position.

– 13 –

Page 15 Page 17
Image 16
Page 15 Page 17
Contents TSP400Z Series EC Council Directive 89/336/EEC of 3 May Table of Contents Unpacking Unpacking and inspectionHandling Notes TSP442Z TSP412ZFerrite core installation *Europe only Parallel interfacePeripheral unit cable Connecting the interface cable Serial interfaceSetting up Loading the Paper RollTemporarily place the paper roll on Adjusting the Head Position Control panel Basic OperationPower switch and on LINE/FEED switch combinations Head UP indicatorPower + on Line + Feed switches Print Density Adjustment Sensor Adjustment ModeEnglish Errors Error Cause BuzzerOther errors only in page mode Buzzer Sounding VariationsTable DES Matieres Déballage Deballage et inspectionRemarques sur la manipulation Identification des pieces et nomenclature Installation du tore de ferrite *Europe uniquement Interface parallèleCâble de périphérique Raccordement du câble d’interface Interface sérieInstallation Chargement du rouleau de papierRouleau de papier Barre de déclenchement Réglage de la position de la tête Faire retourner la tête d’impression enTableau de commande Fonctionnement de baseCommutateur/Témoin on Line EN Ligne Commutateur Feed AvanceTémoin Power Alimentation Témoin Head UP Tete Vers LE HautTémoin manque papier Témoin d’erreurInterrupteur d’alimentation + commutateurs on Line + Feed Mode d’ajustement de capteur Réglage de la densité d’impressionFrench Autres erreurs seulement en mode ErreursErreurs réparables Erreurs non réparablesVariations de tonalité de l’avertisseur sonore Inhaltsverzeichnis Auspacken und Kontrolle AuspackenHinweise AbbFunktion und Bezeichnung der einzelnen Bauteile Installation der Ferritkerne *Nur Europa Parallele SchnittstellePeripheriegerätkabel Anschluss des Schnittstellenkabels Serielle SchnittstelleInbetriebnahme Einlegen der PapierrolleDarauf, daß die Rolle zum Einlegen Einstellung der Druckkopfposition Bedienfeld Grundlegender BetriebAbb Schalter/Anzeige on Line Schalter FeedAnzeige Power Anzeige Head UPKein-Papier-Anzeige FehleranzeigeNetzschalter + Schalter on Line + Schalter Feed Einstellung der Druckdichte SensoreinstellmodusDeutsch Behebbare Fehler FehlerNicht behebbare Fehler Summertonvariationen Sonstige Fehler nur im SeitenmodusIndice Apertura della confezione Apertura e controllo della confezioneAvvertenze Identificazione e nomenclatura delle parti Installazione degli anelli di ferrite *Solo europa Interfaccia parallelaCavo dell’unità periferica Collegamento del cavo d’interfaccia Interfaccia serialeInstallazione Caricamento del rotolo di cartaBarra di strappo Regolazione della posizione della testina Pannello di controllo Operazioni di basePulsante/spia on Line Pulsante FeedSpia Power Spia di erroreSpia Head UP Spia di esaurimento carta3Interruttori accensione + on Line + Feed Regolazione della densità di stampa Modalità di regolazione del sensoreItaliano Errori Errori rimediabiliErrori irrimediabili Altri errori Solo in modalità PaginaVariazione del suono del cicalino Appendix a Specifications General SpecificationsPaper Specifications Print area Appendix Appendix B Dip switch setting Switch Setting BaudConnectors and Signal Names Serial Interface Pin No Signal nameAppendix C Serial interface FunctionInterface Connections Table of Connection Signals for Each Mode Appendix D Parallel interfaceCompatible with Amphenol Cable specifications for peripheral unit Appendix E Peripheral unit drive circuitDrive circuit Recommended drive circuit is shown below Appendix F Memory Switch Settings Head Office Overseas Subsidiary Companies

TSP400Z Series specifications

The Star Micronics TSP400Z Series is an advanced line of thermal receipt printers designed for high-performance and reliability in various retail and hospitality environments. Known for its durability and ease of use, the TSP400Z is equipped with a variety of features that make it an ideal choice for businesses seeking to enhance their transaction processes.

One of the standout features of the TSP400Z is its high-speed printing capability. The printer can achieve print speeds of up to 250 mm per second, ensuring that transactions are processed quickly, which is vital in busy environments. This efficiency helps reduce customer wait times and increases overall satisfaction. Additionally, the printer supports a wide range of paper widths, accommodating various applications and enabling businesses to customize their printing solutions.

The TSP400Z series utilizes advanced thermal printing technology, which eliminates the need for ink or toner, resulting in lower maintenance costs and reduced downtime. The printer is designed with a special auto-cutter feature that ensures clean cuts and precise receipts, further enhancing the user experience. Its drop-in and print paper loading system minimizes setup time, allowing staff to quickly and efficiently reload paper rolls without hassle.

Moreover, the TSP400Z is compatible with a broad range of operating systems, including Windows, Android, and iOS, making it versatile for different business needs. Its Bluetooth and USB connectivity options simplify integration with existing systems, enabling seamless operation across various devices.

Another key characteristic of the TSP400Z is its compact, space-saving design, which is particularly beneficial for businesses with limited counter space. The printer features multiple mounting options, including vertical or horizontal positioning, giving users flexibility in setup.

In addition to its technical specifications, the TSP400Z series focuses on durability. It is designed to withstand the rigors of high-volume printing, with a long lifespan and a robust build that ensures consistent performance even in challenging environments.

In summary, the Star Micronics TSP400Z Series combines speed, efficiency, and reliability with user-friendly features. Its advanced thermal technology, broad compatibility, and compact design make it an excellent choice for businesses looking to improve their printing solutions while enhancing customer service. With the TSP400Z, businesses can streamline their operations and focus on delivering quality service to their customers.
Top Page Image Contents