Star Micronics XR-1500, XR-1000 user manual Paper feeding

Page 78

Paper feeding

If cut sheet paper (without the ASF) is not feeding smoothly, check the following:

Check

Is the paper release lever pushed back (to the f posi- tion)?

Is the paper guide in place and vertical?

Are the left and right guides too close together?

Possible remedy

Set the release lever to the b position.

The paper guide should be in place vertically for cut sheets to feed smoothly.

If the left and right guides are too close together, the paper will not feed smoothly. Move them a little further apart to allow the paper to feed freely.

Is the ASF selected with the Memory Switch settings?

Are you trying to feed paper using the front panel buttons while the ON LINE indicator is ilhuninated?

Is the paper too thick?

If it is, then deselect it.

You can only feed paper in this way when the printer is off-line. Set the printer off-line and then feed paper.

There are limits to the thickness of paper that can be fed in this way. Try with thinner paper.

If fanfold (continuous) paper is not being fed correctly using the tractor feed, check the following:

Check

Is the paper lever pushed to the y position?

Is the paper guide in the ver- tical position?

Are the holes on each side of the paper aligned withregard to each other in the sprock- ets?

Are the sprockets too close or too far apart?

Are the sprockets locked in

position and the covers closed?

Is the paper feeding freely into the printer?

Possible remedy

Make sure the release lever is pushed to the m position.

When using the tractor feed, the paper guide should be horizontal.

If the two sides of the paper are out of alignment, realign them so that the sprocket holes match up.

Misalignment of the sprockets, making the paper too loose or too tight, will prevent a smooth paper feed.

Correct this if necessary.

The paper should not be too far from the printer (less than 1 meter/ 3 feet), and there should be no cables or other obstacles obstructing its path. The paper should also be feeding straight into the. printer, and an angled feed may cause jams and blockages.

72

Page 77 Page 79
Image 78
Page 77 Page 79
Contents XR-1000 Above sto~emm~ applies only to printers marketed in the USA Congratulations Organization of this ManualDIP Switches Table of Contents Replacing the Print Head Front Panel Diagnostic Test Modes TroubleshootingMaintenance Adjusting the Printing GAP IBM Character SET #2UNPACKING, Setting UP and Connection ChapterUser’s manual Setting up Print head shield Connection DIP switch cover Loading Paper Cut-sheet paperFanfold paper continuous stationery Page Once the paper has been loaded Controls and Indicators IndicatorsControls Pitch Setting Pitch Pane/ LockQuiet Mode Font Panel LockPaper Handling Form feedPaper parking Short tear-off function Buffer CLEAR/RESET Test and Maintenance SettingsMicro Feed Setting UP the Memory Switches Iiii Command Menu Menu OptionsPrint Menu Paper MenuForms Menu Courier DRW Factory settingsKNI Offj WFIEmulations Numerical RepresentationCommand Codes and Escape Sequences CBS Example command BothCESC CodesFont style and character set control codes ESCBiIliIIy Select font BothSelect character table Both ValueSelect International Character Set Esc Select primary character set BothSelect secondary character set Both 06h1Select/cancel Undefined control code area Standard Print continuously from the Ail Characters ChartPrint a single character from the Ail Character Chart IBM ES0\ 1Bh5ChSet pica pitch printing Font pitch control codesSet pica pitch printing Standard Esc 1Set elite pitch printing BothSelect/cancel Proportional printing Both Set condensed print mode1Cancel condensed print mode Standard Escsi1Select/cancel expanded printing Special print mode control’codes1Set or cancel pica proportional pitch Select one-line expanded printingCancel one-line expanded print Select Master print modeCancel emphasized print mode Select print modeSelect emphasized Print mode CESCF 1Bh46h 2770Select/cancel Overline Both Cancel double-strike printing Both CEscSelect/cancel Underline Both 1Select double-strike printing BothSelect superscript/subscript Both Cancel superscript/subscript BothLine space control codes Line feed Both1Set line spacing to l/6 inch Standard Set line spacing to l/8 inch BothSet line spacing to 7/72 inch 1Set line spacing to n/216 inch BothExecute ES&A definition Set line spacing to W72 inch1Define line spacing l/72 inch increments One-time line feed in l/216 inch incrementsSet vertical print position in lines Both CEsc Form feed control codesReverse one-time line feed in l/216 inch increments Both Form feedBoth tSet page length in lines Reverse feed to top of formSet page length in inches ESC Cnulb CID1Move to next vertical tab position Both Margins and vertical tab setting control codesSet top-of-form 1Set vertical tab positions Both CEscSelect vertical form unit VFU channel Set VFU vertical tabsSet relative vertical tab positions 1Set bottom margin Both Cancel top and bottom margins BothSet top margin Both Set left and right margins BothSet right margin Horizontal print position control codesSet left margin Both Carriage return Both1Set/clear Horizontal tabs Both Set/cancel Automatic line feedMove to next horizontal tab ES6Set horizontal print position Both Restore tabs to default settingsSet relative horizontal tab positions Both ESC CtP 1Bh 66h 30h 1021Set iustification Mode Both Produce character space StandardSelect Next horizontal print position by dot Copy standard ROM font into RAM Character control codesMove print head Esc CNUI2tandard1Define draft download characters Both 1Define draft download characters 27 61 cd 012~ 20 em Cal a2 cdl ... cdlll1st Graphics Select download/standard character setCESC%n 1Bh25hn Select &dot normal density Both Redefine bit-image mode Double-density BothMiscellaneous codes 1Set MSB to BothSet MSB to 1Select zero style Both 1Cancel MSB control BothCancel last character Standard Backspace BothSet printer on line Both Cancel last line BothSet printer off-line Deselect printer 10 carriage model onlyDeselect printer 15 carriage model only Disable paper-out detection BothEnable paper-out detection Both 1Sound buzzer BothEnable/disable Bidirectional printing Both Enable unidirectional printing for one line only BothExecute macro instruction Enable/disable large character printing Both Enable/disable double-height modeSelect character height, width, line spaclng Both Set/cancel Immediate mode ASF Automatic Sheet Feeder control BothCESC 1Bh 19h Ascii command sequences Select fontBold prlnt Both Select/cancelItalic print Print BothSelect color printing with color option only Both Control ASFMemo Chapter OFF Troubleshooting and Maintenance TroubleshootingPower supply PrintingIf the print is faint, or uneven, check the following Check Paper feeding Check Check Adjusting the Printing GAP MaintenanceRibbon Replacement Now the cover turn the You now to Reusing printer Replacing the Print Head Print head bolts Short test mode Front Panel Diagnostic and Test ModesPage Text test mode Hexadecimal dump mode Lprint CHR$IBidirectional test/adjustment mode Repeat the process for all print modes Memo Installing Application Software with Your Printer ChapterCPI ProportionalSetting UP the Printer from the DOS Prompt Graphics Hard CopyProgramming Using Basic Sample programLprint LOGO$ROW=LOGO$ROW+CHR$GD How the program works Lprint E$ Swsi SW SW Patches necessary to use the Basic interpreter Color displayPrint direction Print pins Line spacingSpeed Unidirectional15model Bit image dot-matrixPacr width CopiesWeight 15 model Power supplyOptions 100 Character Sets ’l-igStandard Character SET #I XJh-lx-l 241 401 661 721 Eel I1041 120101I Standard Character SET #2 SET ##2 1108Rml Lliil 1361 m R168i IIBM Character SET #I Additional Character SET 1NTERNATlONAL Character Sets Denmark/NorwayMemo IDI Graphics direction Graphics dumpRAM usage Ribbon installation, 4 RS232 interface Quiet mode, 11,13,19Unidirectional printing Unpacking Vertical pitch Zero style

XR-1000, XR-1500 specifications

Star Micronics has established itself as a leading provider of premium printing solutions, an assertion further bolstered by its innovative models, the XR-1000 and XR-1500. These thermal receipt printers are designed to meet the diverse needs of retail, hospitality, and various business environments, combining robust features, state-of-the-art technologies, and user-friendly characteristics.

The Star Micronics XR-1000 is engineered for high-performance printing, boasting a print speed of up to 200 mm per second. It ensures swift transaction processing, which is essential in high-volume retail settings. The XR-1500, an advanced counterpart, raises the bar with a higher print resolution, delivering crisp and clear receipts that enhance customer experience. Both models utilize direct thermal printing technology, eliminating the need for ink or toner and significantly reducing operational costs.

One of the standout features common to both models is their compact design, making them suitable for environments with limited space. Their lightweight structure also allows for easy relocation, which is beneficial for businesses with dynamic layouts. Furthermore, the printers are equipped with easy paper loading mechanisms that maximize efficiency and minimize downtime.

Connectivity options are another highlight of the XR-1000 and XR-1500. Both models support a variety of interfaces, including USB, Bluetooth, and Ethernet, allowing seamless integration with existing systems. This flexibility ensures that businesses can adapt to evolving technological requirements without significant overhauls.

Moreover, the XR-1000 and XR-1500 printers are compatible with various point-of-sale (POS) systems and software applications, providing reliable performance across different platforms. Their resilience is notable as well, featuring durable casing and components designed to withstand the rigors of daily use.

The models also incorporate advanced power-saving features, crucial for businesses looking to reduce energy costs without sacrificing performance. Their intuitive LED indicators provide real-time feedback, allowing users to quickly assess the status of the printer.

In summary, the Star Micronics XR-1000 and XR-1500 deliver a high-quality printing experience, characterized by speed, reliability, and flexibility. With their advanced technologies and thoughtful design, these printers stand out as optimal choices for businesses seeking efficiency and quality in their printing solutions. Whether in a bustling retail environment or a busy restaurant, it is clear that these printers offer the solutions that modern businesses need.
Top Page Image Contents