TRENDnet TW100-BRV324 manual Configuring Other Routers on your LAN, Local Router, Buttons

Page 55
Configuring Other Routers on your LAN

Internet Features

Buttons

Save

Save the RIP setting. This has no effect on the Static Routing Table.

 

 

Add Route

Add a new entry to the Static Routing table, using the data shown in

 

the "Properties" area on screen. The entry selected in the list is

 

ignored, and has no effect.

 

 

Update Route

Update the current Static Routing Table entry, using the data shown

 

in the "Properties" area on screen.

 

 

Delete Route

Delete the current Static Routing Table entry.

 

 

Clear

Clear all data from the "Properties" area, ready for input of a new

 

entry for the Static Routing table.

 

 

Routing Table

Generate a read-only list of all entries in the Static Routing table.

 

 

Configuring Other Routers on your LAN

It is essential that all IP packets for devices not on the local LAN be passed to the Broadband VPN Gateway, so that they can be forwarded to the external LAN, WAN, or Internet. To achieve this, the local LAN must be configured to use the Broadband VPN Gateway as the Default Route or Default Gateway.

Local Router

The local router is the Router installed on the same LAN segment as the Broadband VPN Gateway. This router requires that the Default Route is the Broadband VPN Gateway itself. Typically, routers have a special entry for the Default Route. It should be confi- gured as follows.

Destination IP Address

Normally 0.0.0.0, but check your router documentation.

 

 

Network Mask

Normally 0.0.0.0, but check your router documentation.

 

 

Gateway IP Address

The IP Address of the Broadband VPN Gateway.

 

 

Interface

LAN

 

 

Metric

2

 

 

Other Routers on the Local LAN

Other routers on the local LAN must use the Broadband VPN Gateway 's Local Router as the Default Route. The entries will be the same as the Broadband VPN Gateway 's local router, with the exception of the Gateway IP Address.

•For a router with a direct connection to the Broadband VPN Gateway 's local Router, the Gateway IP Address is the address of the Broadband VPN Gateway 's local router.

•For routers which must forward packets to another router before reaching the Broadband VPN Gateway 's local router, the Gate- way IP Address is the address of the intermediate router.

51

Page 54 Page 56
Image 55
Page 54 Page 56
Contents Page Page Table of Contents Document Version1.0 P/N 956YH10001 Copyright 2007. All Rights ReservedChapter Broadband VPN Gateway FeaturesInternet Access Features IntroductionConfiguration & Management LAN FeaturesMicrosoft VPN Gateway Support Package ContentsSecurity Features IPSec VPN Gateway FeaturesFront-mounted LEDs Physical DetailsRear Panel Procedure InstallationRequirements The WAN1 or WAN2 LED should be ON The Power LED should be ONInstallation 5. Check the LEDsTo Do this SetupOverview This Chapter provides Setup details of the Broadband VPN GatewayPreparation Configuration ProgramIf you cant connect Figure 5 Password DialogNavigation & Data Input Home ScreenData - WAN Port Screen WAN Port ConfigurationWAN Port Settings Static IP SettingsButtons PPPoE Dial-upAlso called Network Adapter Address or Physical Address. This is a Port Options ScreenData - Port Options Screen Port OptionsAutomatic Dial-up Bind ServiceMTU Size PPPoE ConnectionData - LAN Port Screen LAN Port ScreenTo Configure your PCs to use DHCP DHCPUsing the Broadband VPN Gateway s DHCP Server Using another DHCP ServerEquilibrium Type has 2 options Load/Backup ScreenData - Load/Backup Screen AdministrationSetup TCP/IP Settings - Overview PC ConfigurationWindows Clients Using DHCP Checking TCP/IP Settings - Windows 9x/MEUsing Specify an IP Address Figure 14 DNS Tab Win 95/98 Figure 13 Gateway Tab Win 95/98Figure 15 Windows NT4.0 - TCP/IP Checking TCP/IP Settings - Windows NT4.0Figure 16 Windows NT4.0 - IP Address Specify an IP Address Obtain an IP address from a DHCP ServerFigure 17 - Windows NT4.0 - Add Gateway Figure 18 Windows NT4.0 - DNS Figure 20 TCP/IP Properties Win Checking TCP/IP Settings - WindowsFigure 19 Network Configuration Win 1. Select Control Panel - Network and Dial-up ConnectionUsing a fixed IP Address Use the following IP Address Figure 21 Network Configuration Windows XP Checking TCP/IP Settings - Windows XP1. Select Control Panel - Network Connection Figure 22 TCP/IP Properties Windows XP Checking TCP/IP Settings - Windows Vista PC Configuration 2. Select Set up or change your Internet Connection Internet AccessAccessing AOL 1. Select Start Menu - Settings - Control Panel - Internet OptionsFixed IP Address Macintosh ClientsLinux Clients Other Unix SystemsOperation Operation and StatusStatus Screen Operation and Status Figure 23 General Status ScreenSystem WAN1/2Firewall KernelData - Port Status Screen Port StatusPort Status Data - Event Log Screen Event LogEvent Log Data - URL Log URL LogInternet Data - System Log Screen System LogSystem Log The following advanced features are provided Address List PC Database Internet FeaturesURL Filter Dynamic DNS Static Routing QoS Data - Address List Screen Address ListAddress List PC Database Screen PC Databasedress, IP Address and Certify Data - PC Database ScreenData - URL Filter Screen URL FilterFilter Strings To add an entry to the list, enter it here, and click the Add button Dynamic DNS Screen Dynamic DNSWeb Site Button Data - Dynamic DNS ScreenOpen Routing and Remote Access Static RoutingOverview Static Routing ScreenStatic Routing Data - Static Routing ScreenLocal Router Configuring Other Routers on your LANOther Routers on the Local LAN For the Broadband VPN Gateway s Routing Table Static Routing - ExampleFor Router As Default Route For Router Bs Default Routelocal router 192.168.1.80 Broadband VPN Gateway sData - QoS Screen Based on QoS rules set below Rules Security ConfigurationRules Screen Outbound/Inbound Connection Data - Rules ScreenData - Define Firewall Rule Screen Define Firewall Rule Inbound/OutboundPort Transfer To Log SettingDest IP Advanced RuleSchedules Screen SchedulesData - Log Screen Firewall -- LogTime Zone Second Server Add New Service ServicesData - Services Screen Available Servicesif not required Data - Security Screen SecurityMAX 3D Engine Options Maximum Con Figure 41 Multi-DMZ E-Mail Log E-MailData - E-Mail Screen E-Mail AlertSelect the desired option for sending the log by E-mail IPSec VPN IPSecPolicies Traffic Selector VPN ConfigurationVPN Endpoint addressVPN Pass-through Common VPN SituationsClient PC to VPN Gateway Figure 45 Connecting 2 VPN Gateways Connecting 2 LANs via VPNOperations VPN ConfigurationPolicies Screen VPN ListCopy Enable/DisableCheck Log Adding a New Policy Figure 47 VPN Wizard - Start Screen Authentication and Encryption General SettingsEnable Policy Allow NetBIOSManual Key Encryption Authentication AlgorithmESP Authentication ESP EncryptionIKE Internet Key Exchange tion is enabledESP SPI This is required if either ESP Encryption or ESP AuthenticaIKE SA Aggressive AuthenticationEncryption Exchange ModeLAN A Gate Example 1 Connecting 2 Broadband VPN GatewaysVPN Examples SettingIPSec SA Parameters Broadband VPN Gateway Configuration Example 2 Windows 2000/XP Client to LANValue Figure 50 Windows 2000/XP - Local Security Settings Windows Client ConfigurationDeselect Activate the default response rule. Click Next Figure 52 IP Filter List Figure 51 Windows 2000/XP - Policy Properties8. Enter the Source IP address and the Destination IP address Figure 53 Filter Properties AddressingFigure 54 New Rule Properties IP Filter List Figure 56 Require Security Properties Figure 55 New Rule Properties Filter Action12. Select Negotiate security this selects IKE, then click Add Figure 58 Require Security Properties VPN SettingWindows Setting Figure 57 Modify Security MethodFigure 60 Authentication Method Figure 59 Tunnel SettingFigure 62 Windows 2000/XP Client to Broadband VPN Gateway Figure 61 Windows 2000/XP Client to Broadband VPN Gateway22. Click OK to save your changes, then Close Figure 63 Filter Properties AddressingFigure 64 Filter List Figure 66 Security Methods Figure 65 Filter ActionFigure 67 Modify Security Method Figure 68 Tunnel SettingFigure 70 DUT to Win2K Properties Figure 69 Authentication Method33. Click the Methods button to see the screen below Figure 72 Key Exchange SettingsFigure 71 Properties - General Tab 32. Click the Advanced button to see the screen belowFigure 76 Broadband VPN Gateway to Windows 2000 Server Example 3 Windows 2000 Server to VPN GatewayFigure 74 IKE Security Algorithms Figure 75 Windows 2000/XP Client to Broadband VPN GatewayFor a single client, this is the same as the Gateway address Remote IP addressesSubnet address 11.5.0.0 Address range used on the remote LAN Figure 77 Windows 2000 Server - Addressing Windows 2000 Server ConfigurationTrusted Certificates CertificatesTrusted Certificates Requesting a Trusted CertificatePrivate Certificate Requests Private CertificateData - Private Certificate Screen Private CertificateButton Requesting a Private CertificateUpload Button New RequestSelect the desired option. RSA is recommended To add a New CRL Data - VPN Status Screen VPN StatusVPN Status Microsoft VPN Server SetupPPTP Service UserData - VPN Adapter Screen Button Data - User ScreenExisting Users PropertiesStatus Log Status Log ScreenService Log Data - Status Log Screen2. Select Make New Connection Windows Client SetupWindows 98/ME 1. Click Start - Settings - Dial-up NetworkingTo establish a connection 2. Select Start - Settings - Dial-up NetworkingWindows ME VPN Dialing Properties Figure 92 Windows 2000 Network Connection WindowsFigure 93 Windows 2000 Public Network Figure 95 Windows 2000 Connection Availability Figure 94 Windows 2000 VPN HostFigure 96 Windows 2000 Finish Wizard Figure 97 Windows XP Network Connection Type Windows XPFigure 98 Windows XP Network Connection Figure 100 Windows XP Public Network Figure 99 Windows XP Connection NameFigure 101 Windows XP VPN Server Figure 102 Windows XP Connection Availability Other Features & Settings DNS Lookup DiagnosticsData - Diagnostics Screen PingSearch Button Password Password ScreenData - Account Management Screen Settings Web ManagementData - Web Management Screen HTTPS//123.123.123.1238080 To connect from a remote PC via the InternetFirmware Upgrade Firmware UpgradeData - Firmware Upgrade Screen To perform the Firmware UpgradeData - Backup/Restore Screen Backup/RestoreThis will delete ALL of the existing settings Default Configu- rationAppendix A TroubleshootingGeneral Problems Internet AccessIt is a security risk, since the firewall is disabled FCC Radiation Exposure Statement Appendix B SpecificationsBroadband VPN Gateway FCC StatementCE Standards CE Marking WarningAppendix B - Specifications Broadband VPN Gateway User Guide
Related manuals
Manual 8 pages 5.73 Kb

TW100-BRV324 specifications

The TRENDnet TW100-BRV324 is a versatile broadband router designed to provide small to medium-sized businesses with reliable networking capabilities. One of its key features is its built-in firewall security, which ensures robust protection against unauthorized access and threats from the internet. This appliance uses Stateful Packet Inspection (SPI), providing a comprehensive barrier against a variety of cyber threats.

Equipped with a DHCP server, the TW100-BRV324 simplifies IP address assignment, allowing administrators to manage network resources efficiently. The device supports both DHCP and static IP configurations, making it flexible for various network setups. Additionally, it offers VPN pass-through capabilities, allowing secure remote access for users needing to connect to the corporate network from outside.

The TW100-BRV324 is noted for its impressive NAT (Network Address Translation) capabilities, which enable multiple devices on a local network to access the internet through a single public IP address. This feature is particularly beneficial in saving costs related to IP addresses while enhancing network management. Furthermore, it boasts an integrated 4-port switch, facilitating wired connections for several devices in a local area network (LAN).

In terms of connectivity, the router supports 10/100 Mbps Ethernet, providing sufficient bandwidth for most small business applications. The device is also easy to set up, thanks to its user-friendly web-based interface, which guides users through the configuration process. This simplicity makes it suitable for individuals with varying levels of networking expertise.

The TW100-BRV324 supports multiple connection types, including DSL and cable internet, ensuring compatibility with various ISPs. Additionally, it embeds Quality of Service (QoS) features, allowing network administrators to prioritize traffic. This is crucial for ensuring that bandwidth-intensive applications, such as video conferencing and VoIP, receive the necessary resources for optimal performance.

In summary, the TRENDnet TW100-BRV324 is a robust and feature-rich router well-suited for small to medium-sized businesses. With its combination of security features, flexible configurations, and user-friendly management tools, it offers a powerful solution for those seeking reliable network performance without the need for extensive technical knowledge.
Top Page Image Contents