Xantrex Technology RS232-HPD, RS232-XT manual Command on

Page 47

 

Operation

 

Command Reference

 

 

 

Command

Description

 

IOUT?

Measures and returns the supply’s actual current output using the built-in

 

current readback circuitry.

 

Response: IOUT <current>

 

 

 

IRDAT <Ilo>,<Ihi>

Calculates and records the slope and offset for readback voltage using

 

IRLO and IRHI data. Set CMODE ON before using this command. See also

 

the calibration procedures in Section 4.

 

<Ilo> and <Ihi> are in <current> format.

 

IRHI

The power supply outputs a current value to an external device connected

 

as part of the calibration procedure and records a current readback value

 

internally. These values are at the high end of the programmed current

 

range. Refer to the output value as IRHI and record it to use as input with

 

the IRDAT command. Set CMODE ON before using this command. See

 

also the calibration procedures in Section 4.

 

IRLO

The power supply outputs a current value to an external device connected

 

as part of the calibration procedure and records a current readback value

 

internally. These values are at the low end of the programmed current

 

range. Refer to the output value as IRLO and record it to use as input with

 

the IRDAT command. Set CMODE ON before using this command. See

 

also the calibration procedures in Section 4.

 

ISET <current>

Sets the power supply’s output current in amps (default) or in milliamps.

 

This programmed current is the actual output in CC mode or the current

 

limit in CV mode.

 

Range: 0 to model maximum output current (IMAX)

 

Initial value: 0 amps

 

 

 

ISET?

Returns the supply’s present output current setting. Does not apply to

 

current settings which are being held. See HOLD command.

 

Response: ISET <current>

 

 

 

LOC <1/ON>,<0/OFF>

Enables or disables local mode operation for the power supply. This

 

command is used with the rear panel Remote switch. See “LOC

 

Command” on page 25.

 

LOC?

Returns the present enabled/disabled setting of local mode operation.

 

Response: LOC 0 (OFF or disabled) or

 

LOC 1 (ON or enabled)

 

 

 

MASK <mnemonics>

Disables the supply's previously unmasked operating conditions from

 

setting bits in the fault and status registers. See “Accumulated Status,

 

Status, and Fault Registers” on page 49. Mnemonics are separated from

 

each other by commas and may be sent in any order.

 

Mnemonics: CV, CC, OV, SD, FOLD, ERR

 

Note: UNMASK NONE = MASK ALL (Initial value)

 

MASK NONE = UNMASK ALL

 

Release 1.1

45

Page 46 Page 48
Image 47
Page 46 Page 48
Contents RS232-HPD Page Internal RS-232 Interface for XT 60 Watt HPD 300 Watt Series Phone 604 422 Toll Free North America 800 667 Fax 604 421 How do you get service?What does this warranty not cover? Disclaimer Product Model Number Serial Number Purchased From Purchase Date Information About Your Power SupplyRelease Release 1.1 Supply SafetyManual Revisions Installation and ConfigurationMain Sections About This Manual Contents Contents Description Features and SpecificationsReadback Functions Features and FunctionsFeatures Features and SpecificationsModels 15-4 20-3 30-2 60-1 120-0.5 250-0.25 SpecificationsModels 15-20 30-10 60-5 Initial Inspection IntroductionPower Supply Front Panel with RS-232 Interface Installed See next page for designation descriptions Open See .13, on LED IndicatorsBasic Setup Procedure Flow Control Selection on See Connector J7 User SignalsSee Power Supply Settings on See Baud Rate Selection onBaud Rate CommunicationsXON Switch Setting Condition Flow Switch Setting ConditionJumper Connections RS-232 Connector Pin Jumper J7 Connections RS-232 Connector Pin Power Supply DCE Host Computer DTE Pin connectorJumper J95 Position Operating State Switch Position Power on resultsCondition Default Settings 60 W 7-6 Model Example RS-232 Connection RS-232 Connector J4 Pinouts default configurationParameter Setting Power Supply Settings13 OVP Control Mode Selection User Options and SettingsHigh OFF LOW User Signals J7 Connector User SignalsJ7 User Signal Connector Circuit Block Diagram J7 User Cable with Ferrite Block Installation and Configuration RS-232 Operation Command SyntaxFormat VoutOperation Floating Number Definition Example Description FormExample Command Description Command SummaryAUXA? Cmode Auxa 1 on Command ReferenceRegister. See Error Codes on Returns the supply’s present foldback setting Command on Status, and Fault Registers on Registers on Accumulated Status, Status, and Fault Registers onReturns the supply’s soft voltage limit setting Accumulated Status, Status, and Fault Registers REM Condition Mnemonic Bit Position Bit WeightError # Error Identification Explanation Error CodesLEDs TroubleshootingCalibration Voltage Voltage Mode CalibrationSetup Voltage Program Calibration ProcedureVoltage Readback Calibration Procedure Current Program Calibration Procedure Current Mode CalibrationCurrent Calibration Setup Current Readback Calibration Procedure Over Voltage Protection OVP Calibration Page Xantrex Technology Inc

RS232-XT, RS232-HPD specifications

Xantrex Technology has made significant strides in the field of power electronics, particularly with its RS232-HPD and RS232-XT communication interfaces. These devices are designed to enhance the efficiency and reliability of power management systems, providing users with advanced features and robust technologies.

The RS232-HPD (High Power Device) is optimized for high-performance applications, enabling seamless communication between power devices and control systems. One of its key features is its compatibility with a wide range of power inverters and converters, making it suitable for diverse applications including renewable energy systems, industrial automation, and marine power solutions. The RS232-HPD supports higher baud rates, allowing for faster data transmission and improved responsiveness in monitoring and control operations.

On the other hand, the RS232-XT (Extended Temperature) variant takes durability to the next level. It is designed to operate in extreme temperature conditions, which is crucial for applications located in harsh environments. The RS232-XT retains all the fundamental benefits of the RS232-HPD while providing additional resilience against temperature fluctuations. This feature is particularly advantageous for outdoor installations, where temperature extremes can impact performance and reliability.

Both the RS232-HPD and RS232-XT are equipped with extensive diagnostic tools that enable users to monitor system performance in real-time. These tools include error detection algorithms and status monitoring, which help in identifying potential issues before they escalate. The user-friendly interface simplifies the setup process, making it accessible for both experienced users and those new to power system management.

A standout characteristic of these interfaces is their robust communication protocols, designed to ensure secure data transmission. With built-in protection against common electrical anomalies, such as voltage spikes and electromagnetic interference, the Xantrex RS232 series guarantees uninterrupted operation and data integrity.

Integration with existing systems is straightforward, thanks to their standard RS232 connectivity. This compatibility makes them ideal for retrofitting older systems without the need for significant infrastructure changes.

In conclusion, Xantrex Technology's RS232-HPD and RS232-XT interfaces are exemplary solutions for advanced power management, offering high performance, durability, and ease of use. Their innovative features and robust technologies solidify Xantrex's position as a leader in the power electronics market. Whether for residential, commercial, or industrial applications, these devices stand ready to deliver efficient and reliable power management solutions.
Top Page Image Contents