Transition Networks SISTF10XX-140-LR(T) specifications Technical Specification, Troubleshooting

SISTF10xx-140-LR(T) / -160-LR(T) / -170-LR(T)

Technical Specification -- Continued

This device has been evaluated as EEx nC IIC T4 equipment under DEMKO Certificate No. 03 ATEX 0324537U. Each module is suitable for use in Zone 2 Explosive Atmospheres. The device must be installed in a minimum IP 54 enclosure as defined in IEC 60529 and EN 60529.

This device is a building-in type. The installation into a certain end equipment shall comply with fire enclosure request of IEC 60950/EN60950 or similar sentence.

EMS Type Tests

Test	Description		Test Levels	Severity
IEC61000-4-2	ESD	Air discharge	+/- 8 KV	3
		Contact discharge	+/- 6 KV	3
		ESD contact discharge	+/- 6 KV	3
IEC61000-4-3	Radiated RFI	Housing	10V/m, 80 MHz - 1 GHz	3
			AM 1 KHz, 80% mod
			10 V/m, 0.9 - 1.8 GHz
			FM 200 Hz 50% square
IEC61000-4-4	Burst	Power supply lines	+/- 2 KV	3
	(Fast Transient)
		Communication lines	+/- 1 KV	3
		Relay	+/- 1 KV	3
IEC61000-4-5	Surge	Power supply lines	+/- 2 KV, 12 Ω, CM	3
			+/- 1 KV, 2 Ω, DM
		Relay	+/- 2 KV, 12 Ω, CM	3
			+/- 1 KV, 2 Ω, DM
IEC61000-4-6	Induced	Power supply lines	10 Vrms, 150-80 MHz	3
	(Conducted RFI)		AM 1 KHz, 80% mod
		Communication lines	10 Vrms, 150-80 MHz	3
			AM 1 KHz, 80% mod
		Relay	10 Vrms, 150-80 MHz	3
			AM 1 KHz, 80% mod

Environmental Type Tests

Test	Description	Test Levels
IEC 60068-2-6	Vibration	10 - 500 - 10 Hz, 0.5 oct./min, 4g, X, Y, Z (3 axes)
IEC 60068-2-27	Shock	50 g, 11 ms, +/-X, +/-Y, +/- Z (6 direction)
IEC 60068-2-32	Free fall	75 cm, 1 corner, 3 edges, 6 faces (total 10 drops)

Troubleshooting

If the device fails, isolate and correct the fault by determining the answers to the following questions and then taking the indicated action:

1.Is the PWR1 LED illuminated?

NO

•Ensure the power source is the proper voltage (12 - 48 VDC).

•Ensure the (+) and (-) wires from the power source are inserted properly in the terminal block contacts labeled “PWR1”.

•Contact Tech Support: 800-260-1312, Int’l: 00-1-952-941-7600.

YES

•Proceed to step 2.

2.Is the PWR2 LED illuminated?

NO

•Ensure the power source is the proper voltage (12 - 48 VDC).

•Ensure the (+) and (-) wires from the power source are inserted properly in the terminal block contacts labeled “PWR2”.

•Contact Tech Support: 800-260-1312, Int’l: 00-1-952-941-7600.

YES

•Proceed to step 3.

3.Is the FAULT LED illuminated?

YES

•If one or more port alarm switches (1 - 5) is ON, the device lost the corresponding fiber or copper link, or the primary power or backup power.

•Ensure the problem copper or fiber link is properly connected.

•Contact Tech Support: 800-260-1312, Int’l: 00-1-952-941-7600.

NO

•Proceed to step 4.

4.Is a 100M LED (near a fiber link) illuminated?

NO

•Check the corresponding fiber cables for proper connection.

•Verify that the TX and RX cables on the device are connected to the RX and TX ports, respectively, on the other device.

•Contact Tech Support: 800-260-1312, Int’l: 00-1-952-941-7600.

YES

•Proceed to step 5.

16 24-hour Technical Support: 1-800-260-1312-- International: 00-1-952-941-7600 techsupport@transition.com -- Click the “Transition Now” link for a live Web chat. 17